Home
Главная
Maxwell
Утюг
MW-3055 B
Инструкция по эксплуатации Страница: 12

Maxwell MW-3055 B [12/36] English

ENGLISH

– Once the soleplate (14) reaches the preset

temperature, the pilot lamp (9) will go out,

you can start ironing.

– Set the necessary steam intensity (from «

•

to «

») with the continuous steam supply

knob (3).

– In the continuous steam supply mode, steam

will be released from the openings of the

soleplate (14) only if the iron is in horizontal

position. To stop the steam supply, put the

iron vertically or set the knob (3) to the posi-

tion «

•

» (steam supply is off).

– After you finish ironing, set the temperature

control knob (11) to the «MIN» position, and

the continuous steam supply knob (3) to the

position «

•

» (steam supply is off).

– Pull the power plug out of the mains socket

and let the iron cool down completely.

ATTENTION!

If steam is not supplied constantly during the

operation, check whether the steam supply con-

trol (3) is set properly and whether there is water

in the water tank (10).

WATER SPRAY

– You can dampen the fabric by pressing the

spray button (5) several times.

– Make sure that there is enough water in the

water tank (10).

BURST OF STEAM

The burst of steam function is useful when iron-

ing of folds and can only be used at high ironing

temperatures (when the temperature control

knob (11) is set to «MAX» position).

When the burst of steam button (4) is pressed,

steam is being released from the soleplate (14)

openings intensively.

Notes: To avoid water leakage from the steam

openings, press the burst of steam button (4)

with 4-5 sec. intervals.

To avoid dripping, do not hold the burst of steam

button (4) longer than 5 seconds.

VERTICAL STEAM

The vertical steam function can be used only

at high ironing temperatures (when the tem-

perature control knob (11) is set to the «MAX»

position).

Hold the iron vertically at the distance of

10-30 cm from the clothes and press the burst

of steam button (4) with a 4-5 seconds interval,

steam will be released from the soleplate (14)

intensively.

Important information

Vertical steam is not recommended for synthetic

fabrics.

– To avoid fabric melting, do not touch it with

the iron’s soleplate while steaming.

– Never steam clothes on a person as the

steam temperature is very high, use a clothes

hanger or a stand.

– After you finish ironing, switch the unit off,

wait until it cools down completely, then open

the water inlet lid (2), turn over the iron and

drain the remaining water.

STEAM CHAMBER CLEANING

To prolong service life of the iron, clean the

steam chamber regularly, especially in the

regions with hard tap water.

– Set the continuous steam supply knob (3) to

the position «

•

» (steam supply is off).

– Fill the water tank (10) till the «MAX» mark

(13).

– Place the iron on its base (8).

– Insert the power plug into the mains socket.

– Set the control knob (11) to the maximum

soleplate temperature «MAX», the pilot lamp

(9) will light up.

– Once the iron soleplate (14) reaches the set

temperature, the pilot lamp (9) will go out.

Wait until the iron soleplate is reheated, then

you can start cleaning the steam chamber.

– Unplug the unit.

– Hold the iron above the sink horizontally,

press and hold the “Self Clean” button (12).

– Boiling water and steam with scale will be

released from the iron soleplate (14) open-

ings.

– Slightly sway the iron back and forth, until all

the water leaves the water tank (10).

– Place the iron on the base (8) and let it cool

down completely.

– When the soleplate (14) cools down com-

pletely, wipe it with a dry cloth.

– Before you take the iron away for storage,

make sure that there is no water in the water

tank (10) and that the soleplate (14) is dry.

CLEANING AND CARE

– Before cleaning the iron, make sure that it

is unplugged and has cooled down com-

pletely.

MW-3055.indd 12 11.02.2014 14:29:22

Maxwell MW-3055 B [12/36] English

Содержание

Похожие устройства