![Antari SW-250X [5/11] Air volume setting](/img/pdf.png)
Antari SW-250X [5/11] Air volume setting
![Antari SW-250X [5/11] Air volume setting](/views2/1992233/page5/bg5.png)
5
4. Заполните резервуар жидкостью ANTARI SL-5(A). Любой другой вид жидкости может повредить устройство. После
заполнения резервуара установите крышку на место.
5. Подключите шнур питания в заземленную розетку и включите питание генератора расположенным на задней па-
нели выключателем.
После включения питания на экране попеременно будут отображаться сообщения “Antari SW-250” и “Wireless Setup...”.
Для регистрации нажмите кнопку “A” на передатчике при отображении на экране сообщения “Wireless Setup”. Подо-
ждите около 15 секунд для завершения регистрации передатчика. По завершении процедуры регистрации экран
начнет мигать и генератор издаст звуковой сигнал. Через 15 секунд на экране будет отображено сообщение “Wireless
Setup.OK”. Вы можете зарегистрировать до 5 передатчиков на генераторе SW-250. Входящий в комплект передатчик
был зарегистрирован на генераторе до его поставки, поэтому может использоваться без предварительной настройки.
Таким образом, регистрация необходима только при использовании нового передатчика W-1.
Регистрация всех передатчиков должна выполняться в течение 15 секунд, затем питание генератора
SW-250 должно быть снова включено для последующей регистрации.
По завершении регистрации передатчика(ов) на экране будет отображено сообщение “Ready To Snow”. Теперь гене-
ратор готов к использованию.
Нажмите кнопку
5
4. Fill with ANTARI SL-5(A) snow fluid. Any other types of fluid can damage the unit. When filled, place cap
back on liquid tank.
5. Plug the power cable into a grounded electrical outlet and switch the power switch at the rear of the
machine for powering on.
After powering on, the LCD screen will show sequentially “Antari SW-250” and then “Wireless Setup…”. Press
button “A” on the transmitter(s) to register when see “Wireless Setup…” is on. There are totally 15 seconds for
finishing the registration of the transmitter(s). Once registration is completed, the LCD screen will blink and
beep. The LCD screen will finally show “Wireless Setup.OK” once the 15 seconds ends. Up to 5 transmitters
are allowed to be registered with one SW-250. The included transmitter has been registered with the machine
before shipment and can be directly operated without any start-up setting. Therefore, the registration is only
needed before use of new W-1.
All transmitter(s) registration must be completed within 15 seconds or SW-250 has to be power on
again for next registration.
After transmitter(s) registration time ends, LCD screen will then show “Ready To Snow”. Now the machine is
ready for operating.
Press button for setting different functions per sequence as below.
To set the interval time under timer mode by pressing and
buttons (20 to 2000 seconds).
To set the duration time under timer mode by pressing U and
для выполнения настроек различных функций, как описано далее.
Для настройки интервала времени нажатием кнопок
6
buttons (10 to 200 seconds).
To set the output volume under timer mode by pressing
and
buttons (1 to 100 %).
To set the output volume under continuous mode by pressing and
buttons (1 to 100 %).
. To set the DMX channel under DMX control mode by pressing and
buttons (1 to 512 channels).
To activate/terminate the wireless control system by pressing and
buttons (ON/OFF). When wireless control system is activated, letter “W” will
be showed under main screen display “Ready To Snow”. Once the wireless control system is
terminated then the letter “W” will disappear accordingly.
To activate / terminate quick start function by pressing and
buttons (ON/OFF). Once Quick Start function is on, the output job under timer
or continuous output (LCD/W-1/DMX) mode terminated by power off will be directly resumed
after power on again. When the unit is power off not under output mode then the LCD screen
will resume to “Ready To Snow” main screen display directly.
Press button to execute the interval/duration timing set and press to stop.
Press button to output continuously until button is pressed.
There’s a small button “” located at rear of the machine used for adjusting the fan output volume.
In general, when the fan output is increased the snow flakes produced are smaller. In contrast, when the fan
и
6
buttons (10 to 200 seconds).
To set the output volume under timer mode by pressing and
buttons (1 to 100 %).
To set the output volume under continuous mode by pressing and
buttons (1 to 100 %).
. To set the DMX channel under DMX control mode by pressing and
buttons (1 to 512 channels).
To activate/terminate the wireless control system by pressing and
buttons (ON/OFF). When wireless control system is activated, letter “W” will
be showed under main screen display “Ready To Snow”. Once the wireless control system is
terminated then the letter “W” will disappear accordingly.
To activate / terminate quick start function by pressing and
buttons (ON/OFF). Once Quick Start function is on, the output job under timer
or continuous output (LCD/W-1/DMX) mode terminated by power off will be directly resumed
after power on again. When the unit is power off not under output mode then the LCD screen
will resume to “Ready To Snow” main screen display directly.
Press button to execute the interval/duration timing set and press to stop.
Press button to output continuously until button is pressed.
There’s a small button “” located at rear of the machine used for adjusting the fan output volume.
In general, when the fan output is increased the snow flakes produced are smaller. In contrast, when the fan
(от 20
до 2000 с) в режиме таймера.
Для настройки длительности работы в режиме таймера нажатием кнопок
6
buttons (10 to 200 seconds).
To set the output volume under timer mode by pressing
and
buttons (1 to 100 %).
To set the output volume under continuous mode by pressing and
buttons (1 to 100 %).
. To set the DMX channel under DMX control mode by pressing and
buttons (1 to 512 channels).
To activate/terminate the wireless control system by pressing and
buttons (ON/OFF). When wireless control system is activated, letter “W” will
be showed under main screen display “Ready To Snow”. Once the wireless control system is
terminated then the letter “W” will disappear accordingly.
To activate / terminate quick start function by pressing and
buttons (ON/OFF). Once Quick Start function is on, the output job under timer
or continuous output (LCD/W-1/DMX) mode terminated by power off will be directly resumed
after power on again. When the unit is power off not under output mode then the LCD screen
will resume to “Ready To Snow” main screen display directly.
Press button to execute the interval/duration timing set and press to stop.
Press button to output continuously until button is pressed.
There’s a small button “” located at rear of the machine used for adjusting the fan output volume.
In general, when the fan output is increased the snow flakes produced are smaller. In contrast, when the fan
и
6
buttons (10 to 200 seconds).
To set the output volume under timer mode by pressing and
buttons (1 to 100 %).
To set the output volume under continuous mode by pressing and
buttons (1 to 100 %).
. To set the DMX channel under DMX control mode by pressing and
buttons (1 to 512 channels).
To activate/terminate the wireless control system by pressing and
buttons (ON/OFF). When wireless control system is activated, letter “W” will
be showed under main screen display “Ready To Snow”. Once the wireless control system is
terminated then the letter “W” will disappear accordingly.
To activate / terminate quick start function by pressing and
buttons (ON/OFF). Once Quick Start function is on, the output job under timer
or continuous output (LCD/W-1/DMX) mode terminated by power off will be directly resumed
after power on again. When the unit is power off not under output mode then the LCD screen
will resume to “Ready To Snow” main screen display directly.
Press button to execute the interval/duration timing set and press to stop.
Press button to output continuously until button is pressed.
There’s a small button “” located at rear of the machine used for adjusting the fan output volume.
In general, when the fan output is increased the snow flakes produced are smaller. In contrast, when the fan
(от 10 до 2000 с).
Содержание
- Генератор снега antari sw 250 руководство пользователя 1
- Введение 3
- Генератор снега antari sw 250 3
- Риск возгорания 3
- Риск поражения электрическим током 3
- Проверка комплектации 4
- Установка и включение питания 4
- Air volume setting 5
- Lcd control operation 5
- Transmitter registration 5
- Настройка функций 5
- Операции на экране 5
- Регистрация передатчика 5
- Air volume setting 6
- Настройка выходного объема вентилятора 6
- Air volume setting 7
- Операции пульта ду 7
- Обслуживание 9
- Операции dmx управления 9
- Предостережение 9
- Approval 10
- Жидкость для производства снега 10
- Технические характеристики 10
- C08sw2501 11
Похожие устройства
- Shure SM58-LCE Руководство по эксплуатации
- Shure BETA 58A Руководство по эксплуатации
- Sennheiser CX 3.00 Руководство по эксплуатации
- Madboy TUBE-402 Руководство по эксплуатации
- Madboy TUBE-202 Руководство по эксплуатации
- Casio Celviano AP-450 Руководство по эксплуатации
- Denn DEK885 Руководство по эксплуатации
- Noname MARSHALL Major II Инструкция по эксплуатации
- Supra SKB-495 Руководство по эксплуатации
- Supra SKB-617 Руководство по эксплуатации
- Ibanez RU10 Руководство по эксплуатации
- Ibanez MU30 Руководство по эксплуатации
- Ibanez PU10 Руководство по эксплуатации
- Ibanez MU40 Руководство по эксплуатации
- Ibanez LU30 Руководство по эксплуатации
- Ibanez GU30 Руководство по эксплуатации
- Ibanez CU40 Руководство по эксплуатации
- Ibanez LU10 Руководство по эксплуатации
- Ibanez CU1 Руководство по эксплуатации
- Ibanez CU30 Руководство по эксплуатации