LINE 6 DT50 212 [5/8] Onnections
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

LINE 6 DT50 212 [5/8] Onnections

LINE 6 DT50 212 [5/8] Onnections
Controlsareconguredforversatilitywithadistinct“chime-y”
quality. Recommended settings: Class A, Pentode (clean) or
Triode (rounder, vintage feel)
IV – Setting IV brings the NFL back in and adds a low frequency
resonance that pairs quite well with high gain voicing applied to
the Channel Controls. Recommended settings: Class AB, Pentode
8. Class A / Class AB Switch – Class A operation is more dynamic
with greater touch sensitivity. Use Class AB operation for greater
headroom and power. In addition to setting the operating class, this
switch also determines the wattage and bias type:
WhensettoClass A the amp is running at25Watts and cathode
biased.WhensettoClass ABtheampisrunningat50Wattsandxed
biased.
Try both settings with each voicing to see what sounds best to you.
9. Pentode / Triode Switch – Thisswitchchangestheconguration
of the power tubes. Set switch to Pentode to sound clear and
commanding. Triode sounds quieter and rounder with a more vintage
feel.
rear Panel Controls & ConneCtions
10. Power Cord Receptacle – Plug the included power cable here.
11. Speaker Outs – Connect speakers here using speaker cables only.
You should only use one output (A, B, or C) at a time and never power
theamplierupwithoutspeakersconnected.Ifyouwanttosilencethe
speakers,usetheStandbyswitch.Thedetailsareasfollows:
Output A isfora4-ohmspeakerload.Youcaneitherhookupone
4-ohmspeaker/cabortwo8-ohmspeakers/cabs
Output Bisforan8-ohmspeakerload.Youcaneitherhookupone
8-ohmspeaker/cabortwo16-ohmspeakers/cabs.
Output Cisforasingle16-ohmspeakerload.
12. Cabinet Simulated Direct Out – Provides a transformer-tapped
direct output with cabinet simulation for studio recording or live
performancewithoutmic’ingyouramplier.Thegroundliftswitchcan
beusedtoeliminatehumorbuzz.
13. Serial Effect Loop – Usetheeffectlooptosendyouraudiosignal
to external effects processors and stomp boxes such as modulations,
delays&reverbs.UsetheLEVEL knob to adjust the incoming signal
strength. Note:Signalpathisinseries.WhenusingtheSEND, audio
will not pass through to the poweramp without a connection back to
the RETURN.
14. Footswitch – ConnectaTip-Sleeve(TS)latchingfootswitchherefor
easy access to switch between Channels A and B.
15. MIDI – IntegrateyourDT50ampintoyourexistingMIDIrig.
16. L6 LINK – isapowerful,proprietaryconnectiondevelopedbyLine6
toenableeasy,reliable,one-cableconnectivitybetweenvariousLine6
products.InthecaseoftheDT50SeriesguitarampliersandPODHD
(300/400/500) series multi-effects processors, this connection allows
both products to sync and communicate uniquely with each other.
L6 LINK passes both audio and control data in a single cable, and
the resulting operation allows users to plug a single cable from their
PODHDfamilyprocessorintoaDT50seriesampandreceivemany
incrediblebenets:
MAINS FUSE – CAUTION:
FOR CONTINUED PROTECTION AGAINST
RISK OF FIRE REPLACE ONLY WITH SAME
TYPE FUSE.
UTILISER UN FUSIBLE DE RECHANGE DE
MEME TYPE ET CALIBRE
120V
~
50 - 60Hz
300W Max
POWER REQUIREMENTS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
TUBE AMP DESIGN BY
100V - 120V =
T5.0AL / 250V SLO-BLO FUSE
220V - 240V =
T2.5AL / 250V SLO-BLO FUSE
FOOTSWITCH
DT50 112
U.S. PATENT NO. 5,789,689
41-00-0291
SERIAL NUMBER
MADE IN CHINADESIGNED IN U.S.A.
®
The power tubes get extremely hot during normal
operation. DO NOT TOUCH!
CAUTION: HOT TUBES!
WARNING/AVIS:
SHOCK HAZARD – DO NOT OPEN. RISQUE DE CHOC ÉLECTRIQUE – NE PAS OUVRIR.
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS EQUIPMENT
TO RAIN OR MOISTURE. TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE
COVER. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR
A CLASS B DIGITAL DEVICE PURSUANT TO PART 15 OF THE FCC RULES. OPERATION
IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE
HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE
RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRABLE OPERATION.
CABINET-SIMULATED DIRECT OUT
SENDRETURN
EFFECT LOOPLEVEL
MIDI
INPUT OUT
(POWER AMP IN) (PREAMP OUT)
SPEAKER OUTPUTS
USE CLASS 2 WIRING ONLY
4 OHM OUT 8 OHM OUT 16 OHM OUT
Connect speakers to ONE
output only – A, B or C.
NEVER OPERATE WITHOUT
SPEAKERS CONNECTED.
(Use STANDBY to silence speakers.)
GND
Use 8 OHM pair OR 4 OHM single Use 16 OHM pair OR 8 OHM single
BC
A
LIFT
TUBE PROTECTION FUSE
CAUTION: FOR CONTINUED
PROTECTION AGAINST RISK OF
FIRE REPLACE ONLY WITH SAME
TYPE FUSE.
UTILISER UN FUSIBLE DE
RECHANGE DE MEME TYPE ET
CALIBRE
T
1
.
0
A
L
/
2
5
0
V
S
L
O
-
B
L
O
F
U
S
E
L6 LINK
THRU
CONNECT TO L6 LINK ONLY

Содержание

Похожие устройства

Скачать