![ADJ Ruby Royal [7/12] This function will allow you to test the pan tilt functions](/img/pdf.png)
ADJ Ruby Royal [7/12] This function will allow you to test the pan tilt functions
![ADJ Ruby Royal [7/12] This function will allow you to test the pan tilt functions](/views2/2009640/page7/bg7.png)
©American DJ® - www.americandj.com - Ruby Royal Instruction Manual Page 14©American DJ® - www.americandj.com - Ruby Royal Instruction Manual Page 13
buttons to select one or the other.
3. When you have made your selection, press the ENTER, and then
press and hold the MENU button for at least 3 seconds to activate. To
exit without making any adjustments press the MENU button.
SENS - Sound sensitivity control.
1. Press the MENU button until “SENS” is displayed, press ENTER.
2. The display will show a number between 0-100. Press the UP or
DOWN buttons to adjust the sound sensitivity. 0 being the least sen-
sitive and 100 the most sensitive.
3. Press the ENTER button to conrm. To exit without making any
adjustments press the MENU button.
BLND - This will control blackout
1. Press the MENU button until “BLND” is displayed, press ENTER.
2. Either “YES” or “NO” will now be displayed. Press the UP or DOWN
buttons to select one or the other.
3. Press the ENTER button to conrm.
LED - With this function the LED display will turn off after 2
minutes.
1. Press the MENU button until “LED” is displayed, press ENTER.
2. Either “ON” or “OFF” will now be displayed. Press the UP or DOWN
buttons to select “ON” to keep the LED display on at all times, or “OFF”
to allow the LED display to turn o after 2 minutes. Press any button to
turn on the LED display again.
3. Press ENTER, and then press and hold the MENU button for at least
three seconds to conrm. To exit without making any adjustments
press the MENU button.
DISP - This function will “ip” the LED display 180º.
Ruby Royal System Menu Ruby Royal System Menu
1. Press the MENU button until “DISP” is displayed, press ENTER.
2. Press ENTER to “ip” the display. Press ENTER to “ip” it again.
Press ENTER when you have decided on your desired display setup.
To exit without making any adjustments press the MENU button.
TEST - This function will allow you to test the pan & tilt
functions.
1. Press the MENU button until “TEST” is displayed, press ENTER.
2. Either “PAN”, “TILT” or “P T” will be displayed. Use the UP or DOWN
buttons to scroll to the function you would like to test and press
ENTER. The function will now run a self test. Press the MENU button
to exit.
FHRS - With this function you can display the running time
of the unit.
1. Press the MENU button until “FHRS” is displayed, press ENTER.
2. The running time of the xture will now be displayed. Press the
MENU button to exit.
VER - This will display the software version
1. Press the MENU button until “VER” is displayed. Press the ENTER
button and the software vesion will be displayed.
2. Press the MENU button to exit.
RSET - Use this function to reset the unit.
1. Tap the MENU button until “RSET” is displayed, press ENTER.
2. The xture will now reset.
Содержание
- Caution 1
- User instructions 1
- Warning 1
- Operation instructions and laser safety 3
- Stop and read all laser safety data 3
- Dmx 512 4
- Power supply 4
- Be sure to follow figures two and three when making your own cables do not use the ground lug on the xlr connector do not con nect the cable s shield conductor to the ground lug or allow the shield conductor to come in contact with the xlr s outer casing grounding the shield could cause a short circuit and erratic behavior 5
- Conductor 5 pin xlr male in 3 pin xlr female out 5
- Data compliment signal 5
- Data true signal 5
- Dmx cable must be daisy chained and cannot be split 5
- Ground shield 5
- Not used 5
- Notice 5
- Pin 4 do not use 5
- Pin 5 do not use 5
- Pin xlr dmx connectors 5
- Pin xlr to 5 pin xlr conversion 5
- Ruby royal set up 5
- Some manufactures use 5 pin dmx 512 data cables for data transmission in place of 3 pin 5 pin dmx fixtures may be implemented in a 3 pin dmx line when inserting stan dard 5 pin data cables in to a 3 pin line a cable adaptor must be used these adaptors are readily available at most electric stores the chart below details a proper cable conversion 5
- Special note line termination 5
- When longer runs of cable are used you may need to use a terminator on the last unit to avoid erratic behavior a terminator is a 110 120 ohm 1 4 watt resistor which is con nected between pins 2 and 3 of a male xlr connector data and data this unit is inserted in the female xlr connector of the last unit in your daisy chain to terminate the line using a cable terminator adj part number z dmx t will decrease the possibilities of erratic behavior 5
- Dmx address setting via control board 6
- In this mode you can run in sound active mode 6
- Set a unit as a slave in a master slave configura tion 6
- Shnd sh 0 sh 1 6
- Show modes 0 18 show mode can run with or without sound active mode activated 6
- Sound sensitivity control 7
- This function will allow you to test the pan tilt functions 7
- This function will flip the led display 180º 7
- This will control blackout 7
- This will display the software version 7
- Use this function to reset the unit 7
- With this function the led display will turn off after 2 minutes 7
- With this function you can display the running time of the unit 7
- Master slave configuration 8
- Operating modes the ruby royal has three different operat ing modes 8
- Shnd is displayed and press enter 8
- Show mode stand alone or master slave 8
- Sound active mode stand alone or master slave 8
- Universal dmx control 8
- Always be sure to dry all parts completely before plugging the unit back in 10
- American d 10
- Be sure the fuse holder is completely and properly seated 4 be sure the unit is not in blackout mode unit does not respond to sound 10
- Be sure you have turned on the unit 2 be sure the external fuse has not blown the fuse is located on the rear panel of the unit 10
- Clean the external optics with glass cleaner and a soft cloth every 20 days 10
- Cleaning frequency depends on the environment in which the fixture operates i e smoke fog residue dust dew in heavy use we recom mend cleaning on a monthly basis periodic cleaning will ensure lon gevity and crisp beam output 10
- Due to fog residue smoke and dust cleaning the internal and external lenses should be carried out periodically to optimize light output 1 use normal glass cleaner and a soft cloth to wipe down the out side casing 10
- Fixture cleaning 10
- Locate and remove the unit s power cord once the cord has been removed located the fuse holder located inside the power socket insert a flat head screw driver into the power socket and gently pry out the fuse holder remove the bad fuse and replace with a new one the fuse holder has a built in socket for a spare fuse be sure not to confuse the spare fuse with active fuse 10
- Low frequencies bass should cause the unit to react to sound tapping on the microphone quiet or high pitched sounds may 10
- No laser output from the unit 10
- Not activate the unit not activate the unit 10
- Ruby royal cleaning 10
- Ruby royal fuse replacement 10
- Ruby royal trouble shooting 10
- Ruby royal warranty 10
- Trouble shooting listed below are a few common problems that you may encounter with solutions 10
- Www americandj com ruby royal instruction manual page 19 10
- Www americandj com ruby royal instruction manual page 20 10
- American dj europe 12
- American dj supply 12
- American dj world headquarters 12
- Auto sensing voltage 12
- Ew kerkrade 12
- Junostraat 2 12
- Model ruby royal 12
- Netherlands 12
- Please note 12
- S eastern ave los angeles ca 90040 usa 12
- Service adjgroup eu www americandj eu 12
- Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice 12
- Tel 31 45 546 85 00 fax 31 45 546 85 99 12
- Tel 323 582 2650 fax 323 582 2610 12
- This fixture contains a automatic volt age switch which will auto sense the voltage when it is plugged into the power source 12
- Web www americandj com e mail info americandj com 12
Похожие устройства
- JENSEN LOUDSPEAKERS P12Q (8 Ohm) Руководство по эксплуатации
- JENSEN LOUDSPEAKERS P12Q (16 Ohm) Руководство по эксплуатации
- AKG Y45 BT Инструкция по эксплуатации
- Ion Audio MOTION DELUXE Инструкция по эксплуатации
- Invotone SYSTEMDRIVE206 Руководство по эксплуатации
- Invotone MX6FX Руководство по эксплуатации
- Invotone MX12FX Руководство по эксплуатации
- Invotone MOD2800LV Руководство по эксплуатации
- Invotone MOD126LV Руководство по эксплуатации
- Invotone MOD2800HS Руководство по эксплуатации
- Invotone IPS16A Руководство по эксплуатации
- Invotone MOD126HH Руководство по эксплуатации
- Involight SLIMPAR784 Руководство по эксплуатации
- Involight SBL2000 Руководство по эксплуатации
- Involight SBL1000HP Руководство по эксплуатации
- ES-ACOUSTIC 115S P4 Руководство по эксплуатации
- Alto L-16MKII Руководство по эксплуатации
- Behringer EUROPOWER PMP 4000 Руководство по эксплуатации
- Behringer ULTRATONE KT 108 Руководство по эксплуатации
- Behringer EURODESK SX 2442FX Руководство по эксплуатации