Vitek VT-2353 черный [4/28] 19 20 21 22 will go out but the functions of the humidifier will continue to work
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Vitek VT-2353 черный [4/28] 19 20 21 22 will go out but the functions of the humidifier will continue to work

Vitek VT-2353 черный [4/28] 19 20 21 22 will go out but the functions of the humidifier will continue to work
4
ENGLISH
•
If the power cord is damaged, it should be
replaced by the manufacturer, a maintenance
service or similar qualified personnel to avoid
danger.
•
Do not attempt to repair the unit. Do not disas-
semble the unit by yourself, if any malfunction is
detected or after it was dropped, unplug the unit
and apply to any authorized service center from
the contact address list given in the warranty
certificate and on the website www.vitek.ru.
•
Transport the unit in the original package only.
•
Keep the unit out of reach of children and dis-
abled persons.
THE UNIT IS INTENDED FOR HOUSEHOLD USE
ONLY. ITS COMMERCIAL USAGE AND USAGE
IN PRODUCTION AREAS AND WORK SPACES IS
PROHIBITED.
BEFORE THE FIRST USE
After unit transportation or storage at low tem-
perature keep it for at least three hours at room
temperature before switching on.
There may be water spots in the air humidifier, this
is normal, as the unit has undergone factory qual-
ity control.
– Unpack the unit, remove any stickers and pack-
age materials that can prevent unit operation.
Check the unit for damages. In case of damages
do not switch the unit on.
– Remove the water tank (4) and remove a trans-
porting plastic part.
– Before plugging the unit in make sure that your
home mains voltage corresponds to the unit
operating voltage.
– The unit is intended for operation with AC system
and 50 or 60 Hz frequency. The unit does not
need any additional settings for operating with
the required nominal frequency.
Notes:
– Use the air humidifier at the room temperature
from +10° С to +40°С, and relative humidity less
than 80%.
– Water temperature should not exceed +40°С.
AIR HUMIDIFIER OPERATION
•
Turn the upper «mist» release nozzle counter-
clockwise.
•
Remove the water tank (4) from the motor
unit (11).
•
Fill the water tank (4) with the required amount of
water without exceeding the MAX mark.
Note: - it is recommended to use water that was
additionally cleaned with domestic filter.
•
Place filled water tank (4) on the motor unit (11).
• Cover the water tank (4) with the lid (3).
• Insert the power plug into the mains socket.
Notes:
– the operation mode selection and setting
buttons are sensory, you just need to touch
the button to switch the necessary operation
mode on, every touch of the active button is
accompanied by a sound signal.
• Switch on the humidifier by pressing the on /
off button (13), a beep will sound and the
LED display (9) will show: relative room air
humidity indicator (19), ionization indicator
(20), wireless network connection indicator
(21), digital symbols of the levels of «mist»
release intensity (22).
Note:
– The humidifier can be controlled in two ways:
from control panel (10) and through TuyaSmart
APP program. A detailed description of the way
to control the humidifier through TuyaSmart
is provided in the instructions for using the
TuyaSmart APP program.
•
To select the intensity of the «mist» output,
consequently press the button (15) on the
control panel (10). The intensity mode will be
shown by digital indicators of the «mist» output
intensity level (22). There are three intensity
modes available:
«Low» - digit «1» is displayed;
«Medium» - digit «2» is displayed;
«High» - digit «3» is displayed.
• To select the mode for setting the relative
humidity in the room consequently press
the button (14) . You can set the desired
level of relative humidity in the room in the
range from 40% to 85% with the step of 5%,
the level of humidity is indicated on the LED
display (9) by digital symbols and indicator
(19) .
• To set the operating time of the timer, succes-
sively press the button (17) and select the
operating time you need in the range from 1 to
12 hours (with the step of 1 hour).
• «Ionization» function is displayed by the ion-
ization indicator (20) when switched on
on the LED-display (9). The function can be
switched off only through TuyaSmart APP.
• «Night mode» function -
Z
Z
after pressing the
button (16)
Z
Z
on the display (9) all indicators
(19, 20, 21, 22) will go out, but the functions of
the humidifier will continue to work.
• If the water tank (4) and the process chamber
(5) are empty, the light indicators will be flash-
ing for 20 seconds and you will hear 3 short
sound signals, after that the indicators (19,

Содержание

Похожие устройства

Скачать