Rondell RDE-1002 черный [5/24] English

Rondell RDE-1002 черный [5/24] English
5
ENGLISH
Avoid leakage and getting liquid on the electric con-
nectors.
This unit is not intended for usage by children.
Place the unit out of reach of children during the operation
and cooling down.
Do not allow children to touch the unit body and the power
cord during the unit operation.
The unit is not intended to be used by people with physi-
cal, sensory or mental disabilities (including children) or
by persons lacking experience or knowledge if they are
not under supervision of a person who is responsible for
their safety or if they are not instructed by this person on
the usage of the unit.
Do not leave children unattended to avoid them using the
unit as a toy.
For children safety reasons do not leave polyethylene
bags, used as a packaging, unattended.
Attention! Do not allow children to play with polyethylene
bags or packaging film. Danger of suffocation!
Check the integrity of the power cord, the power plug and
the kettle body periodically.
Do not use the kettle if the power cord or the power plug
is damaged. If the power cord is damaged, it should be
replaced by the manufacturer, maintenance service or
similar qualified personnel to avoid danger.
Be careful when filling the kettle with water or pouring the
water out and during cleaning, avoid getting water on the
contact block of the kettle and the base.
Depending on the kettle design a small amount of water
may appear on the base due to the condensation of
steam during the kettle operation. It is normal and not
covered by warranty.
Do not repair the unit by yourself. Do not disassemble
the unit by yourself, if any malfunction is detected or
after it was dropped, unplug the unit and apply to any
authorized service center from the contact address
list given in the warranty certificate and on the website
www.rondell.ru.
Transport the unit in the original package only.
Keep the unit out of reach of children and disabled per-
sons.
THIS UNIT IS INTENDED FOR HOUSEHOLD USE ONLY.
ITS COMMERCIAL USAGE AND USAGE IN PRODUCTION
AREAS AND WORK SPACES IS PROHIBITED.
BEFORE THE FIRST USE
After unit transportation or storage at low temperature
keep it for at least three hours at room temperature.
There may be water spots in the kettle, this is normal,
as the unit has undergone factory quality control.
Unpack the kettle and remove any advertising stickers
that can prevent the unit operation.
Check the unit for damages; do not use it in case of
damages.
Make sure that the unit operating voltage corresponds to
the voltage of your mains.
Place the base (9) on a flat, dry, solid and stable surface.
Place the kettle on the base.
To fill the kettle with water, take it off the base (9) and
open the lid (4) by pressing the lid opening button (12).
Fill the kettle with clean water up to the maximal mark
«MAX»; determine the water level using the scale (6),
which is situated under the handle (5).
Close the lid (4) and put the kettle on the base (9). Make
sure that the kettle lid is closed tightly.
Select the desired temperature «60°C-70°C-80°C-90°C-
100°C» by turning smoothly the temperature control knob
(7) clockwise.
ATTENTION! Always unplug the kettle base when filling the
kettle with water or when adding water.
Connect the power plug to the mains socket, the on/off
button (8) illumination will light up blue, and the indicator
(11) will light up under the preset water temperature value.
The kettle will switch to the standby mode.
To switch the kettle on, touch the on/off button (8) « »
for a short time, you will hear a short sound signal, and the
button illumination will light up blue.
After the water boils, you will hear three short sound sig-
nals, the heating will be switched off, the on/off button
(8) illumination will go out and the kettle will switch to the
standby mode.
Pour water out and repeat the water boiling procedure
2-3 times.
Be careful! When you open the kettle lid, some water con-
densed on its inner surface can splash.
ATTENTION! To avoid burns by hot steam, do not bend over
the kettle spout (2) while it is operating.
USING THE KETTLE AND ADDITIONAL FUNCTIONS
Place the base (9) on a flat, dry, solid and stable surface.
Place the kettle on the base.
To fill the kettle with water, take it off the base (9) and
open the lid (4) by pressing the lid opening button (12).
Fill the kettle with clean water up to the maximal mark
«MAX»; determine the water level using the scale (6),
which is situated under the handle (5).

Содержание

Похожие устройства

Скачать