Rondell RDE-1112 Инструкция по эксплуатации онлайн [27/52] 810684

Rondell RDE-1112 Инструкция по эксплуатации онлайн [27/52] 810684
27
Close the protective lid of the ground coffee funnel (9)
аnd the lid of the bean container (8). Use the control
panel buttons (7) (Fig. 10) to select the desired drink.
Wait for the end of the drink preparation process.
Note: The volume of the flat measuring spoon from
the delivery set accommodates the optimal amount of
ground coffee for a single drink preparation. To prepare
a high-quality drink from ready-ground coffee, the opti-
mal weight of dry coffee powder is no more than 9 grams.
Be careful not to add more than one spoonful of ground
coffee, as this may damage the machine. Otherwise, the
coffee powder will spill out of the brewing unit, causing
it to clog and damage. It is unacceptable to pour instant
coffee powder or other freeze-dried coffee-containing
mixtures intended for rapid brewing with hot water into
the ground coffee compartment.
Milk frother
To obtain milk foam, pour milk into a milk container or
insert the milk supply tube (31) directly into the milk.
Place a cup under the coffee supply unit (2). Install
the milk (31) supply tube on the milk system inlet (3) of
the coffee supply unit (2) (Fig. 14) and adjust its height
(Fig. 5). Press the button (21) «Milk».
The display will show information about the making
process (Fig. 15).
As soon as the temperature of the heating unit reaches
the optimum, frothed milk will start to come out of the
coffee supply unit (2).
To stop the frothing process, press the «On/Off/Exit»
button (16) of the control panel (7).
Note: If during the preparation of frothed milk, only milk
comes out of the coffee supply unit (2) or little froth is
formed, then the frother should be adjusted (see the
section «Adjusting the milk supply»).
PREPARATION OF CAPPUCCINO/LATTE
Place a cup under the coffee supply unit (2). Install the
milk (31) supply tube on the milk system inlet (3) of the
coffee supply unit (2) and adjust its height (Fig. 5).
Dip the tube into the milk container (Fig. 14).
To prepare the type of Cappuccino/Latte drink you
need press one of the buttons: «Cappuccino» (19) or
«Latte» (20).
The process of preparing the drink will be reflected
on the display (Fig. 17) and will be completed auto-
matically when the coffee machine prepares the vol-
ume of the drink that was programmed.
You can press the «On/Off/Exit» button (16) to inter-
rupt the drink preparation process.
Hot water supply
Place a cup or other suitable container under the cof-
fee supply unit (2) (Fig. 5). To prevent droplets from
splashing, always adjust the height of the coffee sup-
ply unit (2) to the height of the cup.
Press the «Water» button (24) (Fig. 18), then the
water heating process will begin.
As soon as the temperature of the heating unit
reaches the optimum, hot water will start coming out
of the coffee supply unit (2).
To stop the process, press the «On/Off/Exit» button
(16) of the control panel (7).
Note: The maximum amount of continuous hot water
supply is 250 ml, after which the process of its supply
stops, and the coffee machine goes into the standby
mode (Fig. 8).
FUNCTIONALITY
Preheating of cups
To preserve the taste and aromatic properties of the
prepared drinks, it is recommended to heat the cups
before filling them. To do this, there is a special metal
cup (17) warming tray in the upper part of the coffee
machine (Fig. 19).
Grinding degree control
ATTENTION! The grinding degree should only be
adjusted while the coffee grinder is in operation. Failure
to do so may result in unit damage.
The grinding degree directly depends on the degree
of its roasting. Use coarse grinding for heavily roasted
coffee and finer grinding for lighter roasted coffee.
The grinding degree control knob (14) is located inside
the coffee bean container (10) (fig. 20).
If, when making coffee, coffee pours from the sup-
ply unit (2) very slowly (the grinding is too fine and
the taste of coffee is too strong), turn the grinding