Home
Главная
Bort
Электрические
BHR-1600-SC 98297034
Инструкция Страница: 6

Bort BHR-1600-SC 98297034 [6/24] The suction function

ter to clear off any dirt or grime that may have collected

on the surface. This will allow your detergent to attack

the deep down dirt that has worked its way into the

cleaning surface. Before triggering the gun, adjust the

nozzle to a wide fan pattern and slowly adjust to the

desired spray pattern. This will help you avoid apply-

ing too much concentrated spray to the surface which

could cause damage.

3. Detergent Application

USE THE INSTRUCTIONS APPROPRIATE

FOR MODEL PURCHASED

NOTE: Use only detergents formulated for pressure

washes.

NOTE: Test detergent in an inconspicuous area before

use.

Figure 7 - Detergend application

UNITS WITH DETERGENT APPLICATOR

INCLUDED

Follow manufacturer’s label directions for mixing cor-

rect concentrations of detergent to water ratio through

the pressure washer is approximately 5.4% (1 to 19).

1. Unscrew to top of detergent applicator and ﬁ ll ap-

plicator with detergent.

2. Replace top on applicator.

3. Remove lance from gun.

4. Attach detergent applicator to gun. ( See Figure 8)

Figure 8 - Attach applicator to gun

5. Apply detergent so it thoroughly covers cleaning

surface. Apply from bottom to top to prevent detergent

from sliding down and streaking.

6. Allow detergent to remain on the surface for a few

minutes. This is a good time to use a brush to lightly

scrub heavily soiled areas.

Never allow detergent to dry on the cleaning surface.

7. Remove detergent applicator from gun and replace

with the lance, or remove applicator from end of lance.

8. Rinse detergent from surface.

NOTE: Flush detergent applicator with clear water fol-

lowing each use.

4. Final Rinse

Start ﬁ nal rinse at bottom an work upward. Make sure

you thoroughly rinse the surface and that all detergent

has been removed.

5. Shut down

1. Be sure all detergent is ﬂ ushed from system.

2. Turn off motor.

3. Turn off water supply.

4. After motor and water supply are turned off, trigger

gun to depressurize system.

CAUTION: NEVER turn water supply off before turn-

ing motor off. Serious damage could occur to the pump

and or motor.

WARNING! NEVER disconnect high pressure dis-

charge hose from machine while system is pressur-

ized. To depressurize, turn motor off, turn water supply

off and squeeze gun trigger 2-3 times.

5. After each use, wipe all surfaces of the pressure

washer with a clean, damp cloth.

6. Storage

Do not store pressure washer outdoors.

Do not store pressure washer where it might freeze.

TIPS FOR EXTENDING THE LIFE

OF YOUR PRESSURE WASHER

1. Never operate unit without water.

2. Pressure washer is not meant to pump hot water.

Never connect to hot water supply – this will signiﬁ -

cantly reduce life of the pump.

3. Using detergent other than others brand may cause

damage to pump components (o-rings, etc.).This

also applies to chemicals such as bleach, dish soap,

etc.

4. Never operate unit for more than one (1) minute

without spraying water. Resulting heat buildup will

damage pump.

5. Before adjusting nozzle’s pressure (high-to-low or

low-to-high) release trigger. Failure to do so will re-

duce life of o-rings in lance.

THE SUCTION FUNCTION

You can connect the high pressure cleaner to the water

sources such as taps or pump water from other sourc-

es without pressure.

To work with the water supply without pressure the suc-

tion hose should be removed from the supply and the

gun nozzle should be moved to position “Low” (Figure

14). After that the high pressure cleaner should work

idle for a few seconds to drain the excess water and

release air. Put the suction hose into the water source.

After draining some water the gun nozzle should be

moved to position “High” (Figure 14). Now the high

pressure cleaner is ready to work under high pressure.

TROUBLESHOOTING

1. When switched on, the machine will not start

working.

● Plug is not well connected or electric socket is faulty.

- Check plug, socket and fuse.

● The mains voltage is lower than the minimum re-

quirement for start up.

Check that the mains voltage is adequate.

● The pump is stuck.

- Refer to after storage instructions. Switch off the

unit and let the motor cool.

Bort BHR-1600-SC 98297034 [6/24] The suction function

Содержание

Похожие устройства