Bort KEX-3000 91276308 [5/26] Detergents
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Bort KEX-3000 91276308 [5/26] Detergents

Bort KEX-3000 91276308 [5/26] Detergents
5
toclearoanydirtorgrimethatmayhavecollectedon
the surface. This will allow your detergent to attack the
deep down dirt that has worked its way into the clean-
ing surface. Before triggering the gun, adjust the nozzle
to a wide fan pattern and slowly adjust to the desired
spray pattern. This will help you avoid applying too much
concentrated spray to the surface which could cause
damage.
3. DETERGENT APPLICATION
USE THE INSTRUCTIONS APPROPRIATE FOR
MODEL PURCHASED
(g5)
NOTE: Use only detergents formulated for pressure
washes.
NOTE: Test detergent in an inconspicuous area before
use.
Units with Detergent Applicator Included
Follow manufacturer’s label directions for mixing correct
concentrations of detergent to water ratio through the
pressure washer is approximately 5.4% (1 to 19).
1.Unscrewtotopofdetergentapplicatorandllapplica-
tor with detergent.
2. Replace top on applicator.
3. Remove lance from gun.
4. Attach detergent applicator to gun using connector.
(gure6)
5. Apply detergent so it thoroughly covers cleaning sur-
face. Apply from bottom to top to prevent detergent from
sliding down and streaking.
6. Allow detergent to remain on the surface for a few min-
utes. This is a good time to use a brush to lightly scrub
heavily soiled areas.
Never allow detergent to dry on the cleaning surface.
7. Remove detergent applicator from gun and replace
with the lance, or remove applicator from end of lance.
8. Rinse detergent from surface.
NOTE: Flush detergent applicator with clear water fol-
lowing each use.
The surest way to avoid damaging surfaces is to follow
these steps:
1. Before triggering the gun, adjust the nozzle to a wide
fan pattern.
2. Place the nozzle approximately 4-5 feet from and 45
degrees to the cleaning surface, and trigger the gun.
3. Vary the fan pattern spray angle and the distance to
thecleaningsurfaceuntiloptimumcleaningeciencyis
achieved without damaging the surface.
TURBO NOZZLE (NOT INCLUDED WITH ALL
MODELS)
A turbo nozzle, sometimes referred to as a rotary nozzle,
isaveryeectivetoolthatcansignicantlyreduceclean-
ing time. The turbo nozzle combines the power of a nar-
rowhighimpactstreamandtheeciencyofa25degree
fan pattern. This swirls the narrow high impact stream
into a cone shape that cleans a larger area.
CAUTION: Since a turbo nozzle uses a narrow high im-
pact stream, only use it in applications where the clean-
ing surface cannot be damaged by narrow high impact
spray. Additionally, the turbo nozzle is NOT adjustable
and cannot be used to apply detergent.
DETERGENTS
The use of detergents can dramatically reduce cleaning
time and assist in the removal of dicult stains. Some
detergents have been customized for pressure washer
useonspeciccleaningtasks.Thesedetergentsareap-
proximately as thick as water. The use of thicker deter-
gents, such as dish soap, will clog the chemical injection
system and prevent the application of the detergent.
The cleaning power of detergents comes from applying
them to a surface and giving the chemicals time to break
down the dirt and grime. Detergents work best when ap-
plied at low pressure.
The combination of chemical action and high pressure
rinsingisvery eective.Onvertical surfaces,applythe
detergent starting at the bottom and work your way up-
ward. This will prevent the detergent from sliding down
and causing streaks. High pressure rinsing should also
progress from the bottom to top. On particularly tough
stains, it may be necessary to use a brush in combination
with detergents and high pressure rinsing.
OPERATION
The following cleaning procedure will help you to organ-
ize your cleaning task, and ensure that you achieve the
mostbenecialresultsintheshortestamountoftime.
Remember to use the spraying/cleaning techniques pre-
viously listed.
1. SURFACE PREPARATION
Before starting a pressure wash cleaning job, it is impor-
tant to prepare the surface that is to be cleaned. This is
done by cleaning the area of furniture, and making sure
that all windows and doors are closed tight. In addition,
you should make sure that all plants and trees adjacent
to the cleaning area are protected by a drop cloth. This
will ensure that your plants won’t be sprayed by the de-
tergents.
2. INITIAL HIGH PRESSURE RINSE
The next step is to spray the cleaning surface with water
Figure 5 - Detergend application
CONNECTOR
Figure 6 - Attach applicator to gun

Содержание

Похожие устройства

Скачать