Makita DK0166: дрель-шуруповерт DF0300 + лобзик 4329 [8/24] Drilling in metal

8 ENGLISH

ASSEMBLY

CAUTION: Always be sure that the tool is

switched off and unplugged before adjusting or

checking function on the tool.

Installing or removing driver bit/

drill bit

CAUTION:Afterinsertingthedriverbit/drillbit,

makesurethatitisrmlysecured.Ifitcomesout,do

not use it.

►Fig.5: 1. Tighten 2. Sleeve 3. Ring

Hold the ring and turn the sleeve counterclockwise to

openthechuckjaws.Placethedriverbit/drillbitinthe

chuckasfarasitwillgo.Holdtheringrmlyandturn

the sleeve clockwise to tighten the chuck.

Toremovethedriverbit/drillbit,holdtheringandturn

the sleeve counterclockwise.

Installing hook

Optional accessory

CAUTION: When installing the hook, always

secure it with the screw rmly. If not, the hook

may come off from the tool and result in the personal

injury.

►Fig.6: 1. Groove 2. Hook 3. Screw

The hook is convenient for temporarily hanging the tool.

Thiscanbeinstalledoneithersideofthetool.Toinstall

the hook, insert it into a groove in the tool housing on

either side and then secure it with a screw. To remove,

loosen the screw and then take it out.

Installing driver bit holder

Optional accessory

►Fig.7: 1.Driverbitholder2.Driverbit

Fitthedriverbitholderintotheprotrusionatthetoolfoot

on either right or left side and secure it with a screw.

Whennotusingthedriverbit,keepitinthedriverbit

holders.Driverbits45mm-longcanbekeptthere.

OPERATION

CAUTION: When the speed comes down

extremely, reduce the load or stop the tool to

avoid the tool damage.

►Fig.8: 1. Vent

Holdthetoolrmlywithonehandonthegrip.

Inthecaseofthetwistingaction,holdthegriprmly

withbothhands.

NOTICE: Do not cover vents, or it may cause over-

heating and damage to the tool.

Screwdriving operation

CAUTION: Adjust the adjusting ring to the

proper torque level for your work.

CAUTION: Make sure that the driver bit is

inserted straight in the screw head, or the screw

and/or driver bit may be damaged.

Placethepointofthedriverbitinthescrewheadand

apply pressure to the tool. Start the tool slowly and then

increase the speed gradually. Release the switch trigger

as soon as the clutch cuts in.

NOTE: When driving wood screw, pre-drill a pilot hole

2/3 the diameter of the screw. It makes driving easier

and prevents splitting of the workpiece.

Drilling operation

First,turntheadjustingringsothatthearrowpointsto

the marking. Then proceed as follows.

Drilling in wood

Whendrillinginwood,thebestresultsareobtained

withwooddrillsequippedwithaguidescrew.Theguide

screwmakesdrillingeasierbypullingthedrillbitinto

the workpiece.

Drilling in metal

Topreventthedrillbitfromslippingwhenstartinga

hole, make an indentation with a center-punch and

hammeratthepointtobedrilled.Placethepointofthe

drillbitintheindentationandstartdrilling.

Useacuttinglubricantwhendrillingmetals.Theexcep-

tionsareironandbrasswhichshouldbedrilleddry.

CAUTION: Pressing excessively on the tool

will not speed up the drilling. In fact, this excessive

pressure will only serve to damage the tip of your drill

bit,decreasethetoolperformanceandshortenthe

service life of the tool.

CAUTION: Hold the tool rmly and exert care

when the drill bit begins to break through the

workpiece. There is a tremendous force exerted on

thetool/drillbitatthetimeofholebreakthrough.

CAUTION: A stuck drill bit can be removed

simply by setting the reversing switch to reverse

rotation in order to back out. However, the tool

may back out abruptly if you do not hold it rmly.

CAUTION: Always secure workpieces in a

vise or similar hold-down device.

Makita DK0166: дрель-шуруповерт DF0300 + лобзик 4329 [8/24] Drilling in metal

Содержание

Похожие устройства