Home
Главная
P.I.T.
Насосные станции
POG900-P1
Инструкция к товару Страница: 5

P.I.T. POG900-P1 Инструкция к товару онлайн [5/19] 826135

Self-priming Pump

Place the station on a ﬂ at horizontal surface

and secure through the holes in the supports.

Install (if not installed) high pressure hose.

Assemble the inlet and outlet ducts.

Connect the suction pipe to the inlet, immerse

the pipe in water at a depth of at least 2 m (the

distance to the bottom must be at least 0.5 m).

Suction line connection

Attention!

The suction line (see ﬁ g) must be

installed in such a way that it does not exert

any mechanical stress or stress on the pump.

Attention!

To prevent water from ﬂ owing out

of the turned oﬀ pump, it is imperative to in-

stall a non-return valve on the suction pipe (not

included in the delivery set).

All threaded connections must be sealed with

sealing tape. Air is sucked in through leaks,

as a result of which water absorption decreas-

es or stops.

The suction line must have an inner diameter

of at least 1 ”(25mm). It must be resistant to

creases and vacuum.

The suction line should be as short as possi-

ble, as the supply power decreases with the

increase in the length of the line.

The suction line must constantly rise towards

the pump in order to prevent air pockets from

forming.

A suﬃ cient water supply must be ensured and

the end of the suction line must always be

submerged.

Discharge line connection

Attention!

The discharge line must be in-

stalled in such a way that it does not exert any

mechanical stress or stress on the pump.

All threaded connections must be sealed with

sealing tape to prevent water leakage.

All parts of the pressure pipeline must with-

stand the pressure, their installation is carried

out by qualiﬁ ed specialists.

Danger!

In the presence of fragile parts and

improper installation, the pressure pipe may

burst during operation. Fluid escaping under

pressure can injure you!

To reduce vibrations and noise, the pump

must be connected to the pipeline network

using ﬂ exible connecting hoses.

When installing a pressure water supply,

take into account that:

pump performance directly depends on the

head (water rise). It is not recommended to

use the pump at maximum head - in this case,

the water supply will be minimal.

the hydraulic resistance of 10 meters of the

horizontal section of the line is equal to ap-

proximately 1 meter of lift.

Electrical connection and ground-

ing

– Electrical work, installation of a socket.

Fuses and the connection to the mains

power supply must be done by a qualiﬁ ed

electrician.

– The pump may only be connected to a

properly installed, earthed and tested

shockproof socket.

Filling with water:

– Before starting operation, it is necessary to

ﬁ ll the pumping part with water

– Unscrew the ﬁ ller screw (9)

– Fill the system with water until it fills the

pumping part and suction pipe

– Tighten the screw.

Running

Before using for the ﬁ rst time after assembly,

open all valves, water taps, nozzles and noz-

zles to ensure that air is released from the

system.

Move the switch to the “I” position. The pump

will start pumping water into the system.

Close the shut-oﬀ valves in the discharge line

when there is no air in the water ﬂ owing out of

the pump.

The pump will create the required pressure

and, after the shutdown pressure is reached,

will turn oﬀ automatically.

The pump turns on and oﬀ automatically - as

the water supply is consumed and when the

tank is ﬁ lled.

Note!

The cut-in and cut-out pressures are

preset at the factory and cannot be changed

in the field. Self-adjusting the pressure can

lead to product failure. If cases of self-adjust-

ment are identified, the product is removed

from the warranty. If necessary, additional ad-

justment should be carried out by a specialist.

by the service center.

A thermal switch is installed at your pumping

station to prevent overheating of the pump

electric motor and its failure.

Note!

Periodic shutdown and reclosing of the

station (with constant water consumption) in

the absence of visible malfunctions (extrane-

ous noise, drop in supply pressure, etc.) are

signs that the thermal switch has tripped. This

indicates unfavorable operating conditions:

high temperature of the ambient air or inlet

water; being in direct sunlight; prolonged sig-

niﬁ cant water consumption, causing the pump

to run continuously.

At the end of use, turn oﬀ the station by mov-

P.I.T. POG900-P1 Инструкция к товару онлайн [5/19] 826135

Похожие устройства