Vitek VT-8555 8555-VT-01 [4/20] English
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Vitek VT-8555 8555-VT-01 [4/20] English

Vitek VT-8555 8555-VT-01 [4/20] English
4
ENGLISH
BEFORE THE FIRST USE
After the unit transportation or storage at low
temperature, keep it for at least three hours
at room temperature before switching on.
– Unpack the unit completely and remove any
advertising stickers that can prevent the unit
operation.
– Check the unit for damages; do not use it in
case of damages.
– Before switching on, make sure that the oper-
ating voltage of the power adapter corre-
sponds to voltage of your mains.
– The unit is intended for operation with AC sys-
tem and 50 or 60 Hz frequency. The unit does
not need any additional settings for operating
with the required nominal frequency.
SWITCHING ON
– Place the unit horizontally (pic. 1), turn the lid
(5) clockwise until the marks match (pic. 2)
and remove the lid.
– Remove the HEPA filter (4) from the unit body
(2) (pic. 3).
– Remove the HEPA filter (4) from the packag-
ing materials.
– Install the HEPA filter (4) into the unit body (2).
– Install the lid (5) and turn it counterclockwise
until the marks match (pic. 4).
– Place the unit on a flat steady and dry surface.
– Insert the power plug into the mains socket.
– Switch the unit on by pressing the on/off but-
ton (9) “
“. The buttons (9 and 7) indicators
will light up, the illumination and the first fan
rotation speed (6) will be switched on.
– To select the ventilation mode press the but-
ton (7) “ “, the ventilation mode will change
in «1»-«2»-«3»-«S» sequence. The operation
modes are shown with indicators (6) on the
control panel (3).
“1” - low fan rotation speed
“2” - medium fan rotation speed
“3” - high fan rotation speed
“S” - night mode
– When you set the night mode “S”, the buttons
(7, 9) indicators and the illumination will go out
in 5 seconds, only the night mode indicator (6)
“S” will be glowing. To switch the night mode
off press any button on the control panel (3).
– During the air purifier operation you can
switch the illumination off. To switch the illu-
mination off press the button (8) “
“, the
illumination, the operation mode indication
(6) and the illumination of the buttons (7, 8)
will go out but the button (8) “ “ indicator
will light up. To switch the illumination and the
indicators on press any button on the control
panel (3).
– Ionization function: - when you switch the air
purifier on, the negative ion generator will be
switched on.
– The HEPA filter used in the unit is intended
for 2000 hours. During the first switching on
and when you switch the unit on afterwards,
the remaining operation time timer will be
switched on. After 2000 hours the button (8)
“
“ indicator will light up and start flash-
ing constantly. In this case you have to clean
the HEPA filter (see the chapter “Cleaning the
HEPA filter”).
– To switch the unit off press the on/off but-
ton (9) “
“. The unit will be switched off and
the indicators will go out, after that unplug
the unit.
– The air purifier can operate for a long time, but
you have to follow the safety regulations as
during any other electric appliance operation:
unplug the unit when you don’t need to use it.
CLEANING THE UNIT
Body
– Regularly clean the grids on the bottom part
of the body (2) and the upper grid (1). You can
clean them with a vacuum cleaner.
– Wipe the unit body (2) with a slightly damp
cloth, and then wipe it dry.
– Do not immerse the unit into water or any
other liquids.
– Do not use abrasives and solvents to clean the
unit body (2).
Cleaning the НЕРА filter
– If the button (8) “ “ indicator lights up and
starts flashing, clean the HEPA filter (4).
– Place the unit horizontally (pic. 1), turn the lid
(5) clockwise until the marks match (pic. 2)
and remove the lid.
– Remove the HEPA filter (4) from the unit body
(2) (pic. 3).
– Using a vacuum cleaner with a correspond-
ing attachment clean the outer surface of the
HEPA filter (4).
– Install the HEPA filter (4) into the unit body (2).

Содержание

Похожие устройства

Скачать