Festool PLANEX LHS225-SW с пылеудаляющим аппаратом CTL36 Set 575448 Инструкция к товару онлайн [18/113] 842224

Festool PLANEX IP LHS225-IP/CTM36-Set 575454 Инструкция к товару онлайн [18/113] 842227

7.8 Dust extraction

CAUTION

Breathing in dust can damage the respiratory

passage!

 Always connect the machine to a dust extrac-

tor.

 When performing work that generates dust,

always wear a dust mask.

A Festool dust extractor with an extractor hose

diameter of 27 mm or 36 mm (recommended due

to the improved suction power) can be connected

to the extractor connector [8-2].

 The special extraction hose and special suction

sleeve [8-1] (available as an accessory) ensure

permanent attachment and protect against

kinking.

 For large surfaces, use the mobile dust extrac-

tor CTL/M 36 E AC PLANEX because it guar-

antees the necessary continuous suction power.

 Press the green button [8-4] to open the me-

chanical lock [8-3].

 Attach the extraction hose on the dust extractor

to the outlet spigot [8-2].

 Swivel the mechanical lock [8-3] upwards until

it engages.

8 Operation

WARNING

Risk of injury

 Do not hold the machine by the head.

 Hold the machine with both hands.

 Make sure that all clamping levers are closed

before operating the machine.

 Connect the machine to the mains power sup-

ply.

 Before switching on, hold the sanding head a

slight distance away from the working surface.

 Switch on the machine.

 The on/off switch has a zero voltage actuator,

which prevents the machine from starting auto-

matically after the power supply is interrupted

(e.g. after a power failure). After an interrup-

tion in voltage, press the on/off switch [5-2] to

switch the machine on again.

 Perform the necessary sanding work.

 Do not overload the machine by pressing with

excessive force! The best sanding results are

achieved with moderate press-on pressure. The

sanding performance and quality are mainly de-

pendent on the selection of the correct abrasive.

 Switch the machine off once the sanding task

is complete.

Visual warning signals on the sanding head

The following visual signals appear on the LED

[10-2] on the motor housing and the machine

decreases in speed if necessary.

LED ﬂ ashing slowly

The machine is overheating due to heavy dirt de-

posits around the air vent slits and the dust ﬁ lter

[10-1].

 Clean the air vent slits.

 Remove the dust ﬁ lter [10-1].

 Remove the dirt deposits.

 Insert the dust ﬁ lter [10-1] until it audibly en-

gages.

 The LED stops ﬂ ashing once the machine is

cleaned and cools down. You can then continue

with your work.

If the LED is still ﬂ ashing after the ﬁ lter sieve and

air vent slits have been cleaned:

 Apply less pressure on the surface.

• Reduce the suction output with the handwheel

[5-3].

LED ﬂ ashing quickly

If a malfunction occurs and the speed signal is

transferred incorrectly from the handle to the mo-

tor, the motor increases to maximum speed when

switched on and the LED [10-2] ﬂ ashes quickly

until the machine is switched off.

 The machine has an internal malfunction. Have

the machine inspected by an authorised service

workshop.

9 Service and maintenance

WARNING

Risk of accident, electric shock

 Always pull the plug out of the socket before

performing any type of work on the machine.

 All maintenance and repair work which re-

quires the motor housing to be opened must

only be carried out by an authorised service

workshop.

 Check the plug and the cable regularly and

should either become damaged, have them

replaced by an authorised after-sales service

workshop.

Festool PLANEX LHS225-SW с пылеудаляющим аппаратом CTL36 Set 575448 Инструкция к товару онлайн [18/113] 842224

Похожие устройства