Makita CXT 12В, 46 см, 200 Вт, 3600 рез/мин, 10 положений ножа XPT UN460WDZ [13/92] Maintenance

Makita CXT 12В, 46 см, 200 Вт, 3600 рез/мин, 10 положений ножа XPT UN460WDZ [13/92] Maintenance
13 ENGLISH
The chip receiver gathers discarded leaves and makes
clean-up afterward much easier. It can be installed on
either side of the tool.
1. Align the holes on the chip receiver with the nuts
on the shear blades.
►Fig.16: 1. Nut
2. Hook the claws of the chip receiver to the groove
on the shear blades.
►Fig.17: 1. Claw 2. Groove
3. Press the levers on the chip receiver, and then
hook the claws on the other side to the groove on the
shear blades.
►Fig.18: 1. Lever
To remove the chip receiver, press the levers to release
the claws.
►Fig.19: 1. Lever
NOTICE: Never try to remove the chip receiver
by an excessive force with its claws locked in the
grooves of the shear blades.
OPERATION
Operating the tool
WARNING: Do not use the tool near any
electrical power lines. Contacting with power lines
orusingthetoolnearpowerlinesmaycauseserious
injuryorelectricshockresultingindeath.
WARNING: Keep hands away from shear
blades.
WARNING: Be extremely careful to maintain
control of the tool at all times. Do not allow the
tool to be deected toward you or anyone in the
work vicinity. Failure to keep control of the tool
couldresultinseriousinjurytothebystanderandthe
operator.
CAUTION: Avoid operating the tool in very
hot weather as much as practicable. When operat-
ing the tool, be careful of your physical condition.
CAUTION: Be careful not to accidentally
contact a metal fence or other hard objects while
trimming.Theshearbladesmaybreakandcause
aninjury.
CAUTION: Be careful not to allow the shear
blades to contact the ground.Thetoolmayrecoil
andcauseaninjury.
CAUTION: Overreaching with a hedge trim-
mer, particularly from a ladder, is extremely
dangerous.Donotworkwhilestandingonanything
wobblyorinrm.
NOTICE: Do not attempt to cut branches thicker
than 10 mm in diameter with the tool. Cut branches
to 10 cm lower than the cutting height using branch
cutters before using the tool.
►Fig.20: (1) Cutting height (2) 10 cm
NOTICE: Do not cut down dead trees or similar
hard objects.Doingsomaydamagethetool.
NOTICE: Do not trim the grass or weeds while
using the shear blades.Theshearbladesmay
become tangled in the grass or weeds.
Holdthetoolwithbothhandsbyholdingthefrontgrip
and the rear grip.
►Fig.21: 1. Front grip 2. Rear grip
Pulltheswitchtriggerwhilepressingthelock-o󰀨button,
and then move the tool forward.
►Fig.22
For basic operation, tilt the shear blades toward the
trimmingdirectionandmoveitcalmlyandslowlyatthe
speed rate of 3 to 4 seconds per meter.
►Fig.23
Tocutahedgesideevenly,cutfromthebottomtotop.
►Fig.24
When trimming to make a round shape (trimming boxwood or rho-
dodendron,etc.),trimfromtheroottothetopforabeautifulnish.
►Fig.25
If the chip receiver is attached to the shear blades, it gathers
discarded leaves and makes clean-up afterward much easier.
►Fig.26
MAINTENANCE
CAUTION:
Always be sure that the tool is
switched o󰀨 and the battery cartridge is removed before
attempting to perform inspection or maintenance.
CAUTION:
When inspecting or maintaining the
tool, always put the tool down.Assemblingoradjusting
thetoolinanuprightpositionmayresultinseriousinjury.
To maintain product SAFETY and RELIABILITY,
repairs,anyothermaintenanceoradjustmentshould
beperformedbyMakitaAuthorizedorFactoryService
Centers,alwaysusingMakitareplacementparts.
Cleaning the tool
Cleanthetoolbywipingo󰀨dustwithadryclothorone
dippedinsoapywaterandwrungout.
NOTICE: Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
Shear blade maintenance
Before the operation or once per hour during operation,
applylow-viscosityoil(machineoil,orspray-typelubri-
cating oil) to the shear blades.
►Fig.27
After operation, remove dust from both sides of the
shearbladeswithawiredbrush,wipeito󰀨withacloth
andthenapplylow-viscosityoil(machineoil,orspray-
typelubricatingoil)totheshearblades.
►Fig.28

Содержание

Похожие устройства

Скачать