FERM FX Power JSM1039 [8/48] Operation
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

FERM FX Power JSM1039 [8/48] Operation

FERM JSM1039 [8/48] Operation
8
EN
Replacing the saw blade
Fig. A, B
When mounting the saw blade, wear
protective gloves. Danger of injury when
touching the saw blade.
Only use saw blades that correspond
with the characteristic data given in the
operating instructions.
Fold the Guard (12) upwards before replacing
the saw blade. Always saw with the guard folded
downwards.
Mounting the saw blade
Make sure the blade holder is free of material
debris (such as splinters of wood or metal).
1. Turn the clamping lever (13) as far to the left as
possible and hold it in this position.
2. Insert the saw blade in the chuck (16). Check
that the saw blade is securely fixed and that
the teeth are pointing in the cutting direction.
3. Let go of the clamping lever. Check whether the
back of the saw blade is positioned in the centre
of the guide roller (10). Make sure to use the right
sawblade for the corresponding material. Included
with the machine is a coarse sawblade for wood
and a fine sawblade for metal and plastics.
Removing the saw blade
1. Turn the clamping lever (13) as far to the left as
possible and hold it in this position.
2. Remove the saw blade from the chuck (16).
3. Let go of the clamping lever.
Attaching the parallel guide
Fig. C
1. Loosen the bolts (14).
2. Mount the parallel guide (19) onto the
baseplate (9).
3. Set the desired cutting width using the scale
on the parallel guide (19) and the cutting mark
on the baseplate (9). The cutting mark (21)
indicates the position of the saw blade.
4. Tighten the bolts (14).
4. OPERATION
Switching the machine on/off
Fig. A
The on/off switch (2) is used for activating the
machine and adjusting speed.
•
To start the machine, press and hold the lockoff
button (1) and press the on/off switch (2).
• The further the on/off switch (2) is being
pushed, the faster the blade will move. The
required speeds depends on the material and
can be determined by practical testing.
• To stop the machine, release the on/off switch
(2).
Adjusting the bevel angle
Fig. A, D
1. Loosen the bolts (18), using the hex key (15).
2. Adjust the baseplate (9) to the desired position
(0°- 45°). The sawing angle (bevel) can be read
on the scale (7).
3. Tighten the bolts (18), using the hex key (15).
It is possible to store the hex key onto the
machine, as shown on Fig. A.
Adjusting the pendulum action
Fig. A
The pendulum action switch (6) is used to set the
way in which the teeth of the saw blade grip the
material. The pendulum action switch can be set
to 4 positions:
0 - No pendulum action
1 - Small pendulum action
2 - Medium pendulum action
3 - Large pendulum action
The required pendulum action can be determined
by practical testing, although the following
instructions can be observed:
• Soft material (wood, plastics etc.): set the
pendulum to level II or III. For a finer and
cleaner saw cut, use pendulum level 0 or I.
• Thin material, use pendulum level 0.
• Hard material (hardwood, steel etc.): set the
pendulum to level 0.
• Curves: set pendulum to level 0.
Dust extraction
Fig. E
• Insert the dust extraction adapter (8) into the
dust extraction connection (22).
• Connect the hose of a vacuum cleaner to the
dust extraction adapter (8).

Содержание

Похожие устройства

Скачать