Home
Главная
Al-Ko
Роботы-газонокосилки
Robolinho 500 I 119834
Инструкция к AL-KO Robolinho 500 I 119834 Страница: 50

Al-Ko Robolinho 500 I 119834 Инструкция к AL-KO Robolinho 500 I 119834 онлайн [50/504] 868063

50 Robolinho

Start-up

LEDs Operating states

Yellow

■

Lights up if the power source is

intact.

5 START-UP

This chapter describes the activities and settings

that are necessary to put the appliance into oper-

ation for the first time. For all further settings, re-

fer to see chapter 7 "Settings", page51.

5.1 Charging the rechargeable battery (08)

During normal operation, the battery of the appli-

ance is regularly charged automatically.

NOTE Fully charge the rechargeable bat-

tery before using it for the first time. The re-

chargeable battery can be charged in any charge

status. Interrupting charging does not damage

the rechargeable battery. The rechargeable bat-

tery can only be charged after the appliance has

been switched on.

1. Place the appliance (08/1) in the base station

(08/3) so the contact surfaces of the appli-

ance touch the charging contacts of the base

station.

2. Switch on the appliance with .

3. The display on the appliance shows Bat-

tery is being recharged. If not: see

chapter 13 "Help in case of malfunction",

page58.

5.2 Making the basic settings

1. Open the cover flap.

2. Switch on the appliance with . Firmware,

code and type are displayed.

3. In the menu for language selection, select the

language with or and accept with

4. In the Login > Enter PIN menu, enter the

preset PIN 0000. To do so, select the digit 0

with or in sequence and always ac-

cept with . After entering the PIN, access

is enabled.

5. In the Change PIN menu:

■

Under Enter new PIN, enter a self-se-

lected new four-digit PIN. To do so, se-

lect one digit in sequence with or

and respectively confirm with .

■

Under Reenter new PIN, enter the

new PIN again. If both entries are identi-

cal, PIN changed is displayed.

6. In the Enter date menu, set the current

date (format:DD.MM.20YY). To do so, select

one digit in sequence with or and re-

spectively confirm with .

7. In the Enter time > HH:MM menu, set the

current time (format:HH:MM). To do so, se-

lect one digit in sequence with or and

respectively confirm with .

The basic settings have been completed. The

Not calibrated Press Start key status

is displayed.

5.3 Setting the cutting height

The cutting height can be manually adjusted con-

tinuously between 25–55mm.

NOTE A cutting height of 55mm is recom-

mended for the calibration movement (see chap-

ter 5.4 "Carrying out an automatic calibration

movement", page50) and for teaching-in the

starting points (see chapter 7.5.2 "Setting the

start points", page52).

1. Open the cover (10/1).

2. Set the cutting height (the current cutting

height is displayed in the window(10/3) in

millimetres):

■

Increase the cutting height (i.e. lawn

height): Turn the rotary knob(10/2) clock-

wise(10/+).

■

Decrease the cutting height (i.e. lawn

height): Turn the rotary knob(10/2) anti-

clockwise(10/–).

3. Close the cover.

5.4 Carrying out an automatic calibration

movement

NOTE Before commissioning, carry out the

calibration movement (see chapter 5.4 "Carrying

out an automatic calibration movement",

page50) or teaching-in of the starting points

(see chapter 7.5.2 "Setting the start points",

page52).

Al-Ko Robolinho 500 I 119834 Инструкция к AL-KO Robolinho 500 I 119834 онлайн [50/504] 868063

Похожие устройства