Al-Ko Robolinho 500 I 119834 Инструкция к AL-KO Robolinho 500 I 119834 онлайн [51/504] 868063
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Al-Ko Robolinho 500 I 119834 Инструкция к AL-KO Robolinho 500 I 119834 онлайн [51/504] 868063

Al-Ko ROBOLINHO 500 W 119925 Инструкция к AL-KO Robolinho 500 I 119834 онлайн [51/504] 868064
442811_a 51
Operation
Place the appliance at the starting position
(09)
1. Place the appliance at the starting position in-
side the mowing area:
■
At least 1m left and 1m in front of the
base station
■
Aligned with the front side to the bound-
ary cable
Starting the calibration movement
1. Check that there are no obstacles in the ex-
pected movement area of the appliance. The
appliance must be able to move over the
boundary cable with both front wheels. If nec-
essary, remove obstacles or lay the cable
temporarily inwards (min.35cm required).
2. Start the appliance with . The following is
shown on the display:
■
! Caution ! Starting Motors
■
Calibration , Phase [1]
During the calibration movement
To determine the signal strength inside the
boundary cable, the appliance first moves twice
straight beyond the boundary cable and then into
the base station and comes to a stop there.
■
The Calibration completed message is
shown on the display.
■
The rechargeable battery is being charged.
NOTE The appliance must come to a stop
when it moves into the base station. If the appli-
ance does not touch the contacts when it moves
into the base station, it moves further along the
boundary cable. If the appliance moves through
the base station, the calibration procedure has
failed. In this case, the base station must be bet-
ter aligned and the calibration procedure repeat-
ed.
After the calibration movement
The preset current mowing duration is displayed.
For all further settings, refer to see chapter 7
"Settings", page51.
Robolinho 700/1200/2000
NOTE To ensure proper operation and re-
duce error messages, the loop length must be
measured.
See also
2 Setting the start points [}52]
6 OPERATION
6.1 Starting the appliance manually
1. Switch on the appliance with .
For unscheduled edge mowing: see chapter
7.7 "Edge mowing with a manual start",
page54.
2. Start the appliance manually with .
6.2 Cancelling mowing
■
Robolinho 500/1150: Press on the appli-
ance.
■
Robolinho 700/1200/2000: Press on the
base station (08/4) or on the appliance.
The appliance moves automatically into the base
station. It deletes the mowing plan of the current
day and starts again the next day for the set time.
■
Press on the appliance.
The mowing is interrupted for half an hour.
■
Press on the appliance.
The appliance is switched off.
NOTE In dangerous situations, the appli-
ance can be stopped with the STOP but-
ton(08/2).
6.3 Mowing the secondary area (01/NF)
1. Lift the appliance and place in the secondary
area by hand.
2. Switch on the appliance with .
3. Call up the main menu with .
4. or * Settings
5. or * Sub zone mowing
6. Select the mowing time with or .
7. Start the appliance manually with .
Depending on the setting: The appliance mows
for the set time period and then switches off or
mows until the rechargeable battery is flat.
After mowing the secondary area, place the ap-
pliance in the base station again by hand.
7 SETTINGS
7.1 Calling up the setting – General
1. Call up the main menu with .
Note:The asterisk * in front of the menu item
indicates that it has just been selected.

Похожие устройства

Скачать