Home
Главная
GEOS
Электрические
MH 2810 EASY CRUSH 213872
Manual_AL-KO - GEOS 213872 Страница: 23

GEOS MH 2810 EASY CRUSH 213872 Manual_AL-KO - GEOS 213872 онлайн [23/216] 871936

GEOS MH 2810 EASY CRUSH 213872 Manual_AL-KO - GEOS 213872 онлайн [23/216] 871936

442981_b 23

Start-up

4. Slide the medium 8x20x1.5 washer (02/6) on-

to the thread and secure the transport wheel

using an M8 nut (02/7).

5. Finally, press the wheel cap (02/8) onto the

transport wheel (02/5).

6. Fit the opposite transport wheel in the same

sequence.

5.2 Fitting shredder upper section with

cutting unit and motor unit (03)

1. Lift the shredder upper section onto the base

and secure it using M5x30 bolts (03/1) and

washers 5x10x1.

5.3 Fitting the hopper (03)

1. Place the hopper onto the shredder upper

section and secure it using ST 4.2x18 bolts

(03/2).

6 START-UP

■

Comply with working time regulations in force

in your country.

■

Do not route the extension lead over the hop-

per or under the discharge opening.

■

The shredder can only be started when the

collector box is locked.

■

Check the hopper and shredder upper sec-

tion (MH2810) or hopper (LH2810) for ob-

structions before starting the machine.

■

LH2810: The counterplate (07/2) is factory-

calibrated and must not be adjusted during

initial start-up.

■

Do not use the shredder if you are:

■

Tired

■

Unwell

■

Under the influence of alcohol, medicines

and drugs

DANGER! Danger of injury from dam-

aged components! Damaged components can

lead to serious and even fatal injuries!

■

Before putting into operation, carry out a vi-

sual inspection and check the components

for function.

WARNING! Risk of injury due to negli-

gence! Negligence in handling the machine can

result in serious injuries!

■

Only use the shredder on firm, level ground

and in a stable position. Do not tilt or incline

the machine during operation.

7 OPERATION

WARNING! Danger of serious injury!

There is a risk of serious injuries for children, per-

sons with impaired physical, sensory or mental

abilities, persons with insufficient knowledge and

experience and persons who are not familiar with

the operating instructions.

■

Never permit the above persons to use the

machine.

■

Always observe the local regulations con-

cerning the age limit for users.

7.1 Connecting the mains plug (04/05)

1. Push down the cable lock (04/1) and insert

the extension lead (05/1) into the socket of

the shredder.

2. Check that the extension lead is connected

securely.

3. Then connect the extension lead to the mains

voltage.

7.2 Switching on the motor (06)

MH2810

1. Press the ON switch (06/1).

LH2810

Normal operation:

1. Turn the direction of rotation switch (06/4) of

the cutting drum to the left (06/6).

2. Then press the ON switch (06/1).

3. The material to be shredded is pulled in.

Reverse:

See see chapter 7.4 "Clearing a cutting disk/cut-

ting drum blockage", page23.

7.3 Switching off the motor (06)

1. Press the OFF switch (06/2) to switch the

motor off.

CAUTION! Damage to the machine due to

improper operation! Incorrect handling can re-

sult in machine damage!

■

Only feed material to be shredded after the

machine has been switched on.

■

Do not feed material to be shredded after the

machine has been switched off.

7.4 Clearing a cutting disk/cutting drum

blockage

Clearing a cutting disk blockage (MH 2810)

(09/10 )

1. Switch off the shredder.

Похожие устройства