Home
Главная
GEOS
Электрические
MH 2810 EASY CRUSH 213872
Manual_AL-KO - GEOS 213872 Страница: 24

GEOS MH 2810 EASY CRUSH 213872 Manual_AL-KO - GEOS 213872 онлайн [24/216] 871936

Maintenance and care

2. Disconnect the machine from the mains pow-

er supply.

3. Loosen locking screw (09/1) and remove

shredder upper section (09/2).

4. Remove the material causing the blockage.

5. Check cutting disk and shredder blade (10/3)

for damage.

6. Position the shredder upper section (09/2)

and tighten the locking screw (09/1) again.

7. Reconnect the machine to the mains power

supply.

8. Switch on the shredder again.

CAUTION! Danger of crushing when

opening and closing the housing! Hand and

finger injuries may occur!

■

Beware of your hands and fingers when

opening and closing the housing.

Clearing a cutting drum blockage (LH 2810)

(06/08)

1. Switch off the shredder.

2. Turn direction of rotation switch (06/4) to the

right (06/5) and press the ON switch (06/1)

(reverse). The material to be shredded

should now be released upwards.

3. Switch off the machine and wait for the cut-

ting drum to come to a standstill.

4. Turn the direction of rotation switch (06/4) to

the left (06/6) again.

5. Switch on the shredder again.

If the material to be shredded is not released up-

wards:

1. Loosen the adjusting screw of the counter-

plate (08/1), until the cutting drum runs freely

again and the blockage is cleared.

2. Readjust the counterplate, see description

"Readjusting the counterplate".

If the blockage cannot be cleared, contact our

customer service.

WARNING! Risk of injury due to lack of

concentration while working! Ejected parts can

cause very severe injuries!

■

Watch out for flying parts and keep your face

away from the feed chute.

7.5 Emptying the collector box (11/12)

1. Switch off the shredder.

2. Pull the lock (11/1) down and the collector

box (11/2) out of the base.

3. Place the empty collector box (12/2) onto the

guide rail (12/1) and push it completely into

the base.

4. Push lock (12/3) up until it engages.

8 MAINTENANCE AND CARE

DANGER! Fatal electric shock hazard!

Touching live parts poses an immediate risk of

fatal injury due to electric shock.

■

Disconnect the appliance from the mains pri-

or to all maintenance, care and cleaning

work.

WARNING! Danger of lacerations. Danger

of cutting injuries when reaching into sharp-

edged, moving appliance parts and into cutting

tools.

■

Before maintenance, care and cleaning work,

always switch off the appliance. Disconnect

the appliance from the mains power supply.

■

Always wear protective gloves during mainte-

nance, care and cleaning work.

WARNING! Risk of injury during repair

work. Improper repairs can lead to serious inju-

ries and damage to the appliance.

■

Have repair work performed by the manufac-

turer's service centres and authorised spe-

cialist companies only!

■

After each use, check the shredder for wear

and renew any damaged components.

■

Keep venting slots free of remnants and ac-

cumulations.

■

Only use spare parts specified by the manu-

facturer.

8.1 Shredder blades (MH 2810)

To obtain an optimum shredding result and pre-

vent damage to the machine, the blades must be

replaced at regular intervals.

■

Always replace the blades in pairs.

■

Always tighten the bolts securely.

■

Do not work with blunt blades.

8.2 Replacing/turning the shredder blades

(MH 2810) (11/12)

Replacement blades for Easy Crush MH 2810

Art. No. 113079

1. Switch off the shredder and disconnect it

from the mains power supply.

2. Loosen locking screw (11/1) and remove

shredder upper section (11/2).

GEOS MH 2810 EASY CRUSH 213872 Manual_AL-KO - GEOS 213872 онлайн [24/216] 871936

Похожие устройства