Sea-Doo RXT iS 2009 Инструкция по эксплуатации онлайн [227/555] 12044
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Sea-Doo RXT iS 2009 Инструкция по эксплуатации онлайн [227/555] 12044

Sea-Doo GTX Limited iS 2009 Инструкция по эксплуатации онлайн [227/555] 12053
Section 03 ELECTRONIC MANAGEMENT SYSTEMS
Subsection 04 (MONITORING SYSTEM AND FAULT CODES)
FAULT
CODE
MODULE DESCRIPTION POSSIBLE CAUSE SERVICE ACTION
P0358
ECM
Ignition Powe
rStage
fault-shortcircuitto
V+/Cylinder 2
Damaged coil, damaged
circuit wires, damaged
connector or damaged
ECM output pins
Check for 0.85 t
o1.15ohms
between engine connector pin 1 and
ECM connector pin A-M2.
Check for 12 vo
lts on pin 2 of
coil connector.
Check fuse 8 (refer to
WIRING
DIAGRAM
).
Refer to the Service Manual for
more details.
P0359
ECM
Ignition Power Stage
fault-shortcircuitto
V+/Cylinde
r3
Damaged coil, damaged
circuit wires, damaged
connector or damaged
ECM output pins
Check for 0.85 to 1.15 ohms
between engine connector pin 3 and
ECM connect
or pin A-M1.
Check for 12 volts on pin 2 of
coil connector.
Check fuse 9
(refer to
WIRING
DIAGRAM
).
Refer to the Service Manual for
more detai
ls.
P0512
ECM
Starter power stage
detects high current
Damaged solenoid,
damaged circuit wires,
damaged c
onnector or
damaged ECM
Verify 5 A fuse.
Check for 1
2 volts on pin 2 of
the starter relay.
Refer to the Service Manual for
more deta
ils.
P0513
ECM
Invalid D.E.S.S. Key
detected
Key not programmed in
ECU
Program a good key.
P0520
ECM
Oil pressure switch
functional problem
Engine leak, oil pump
failure, damaged sensor,
damaged circuit wires,
damaged connector or
damaged ECM pins
Check resistance at 0 RPM and
above 350
0RPM.
Switch is normally closed, ECM
connector pin A-E3.
When blo
w-by pressure exceeds
40 kPa (6 PSI), the resistance is
infinitely high.
Refer to
the Service Manual for
more details.
P0523
ECM
Oil pressure sensor
fault
Engine
leak, oil pump
failure, damaged sensor,
damaged circuit wires,
damag
ed connector or
damaged ECM pins.
Fault detected when
the en
gine is running or
stopped
Check resistance at 0 RPM and
above 3500 RPM.
When blow-by pressure exceeds
40 kPa (6 PSI), the resistance is
infinitely high.
Refer to the Service Manual for
more details.
P0524
ECM
Low oil pressure
condition
Low oil level, engine leak,
oil pump fault.
Check
oil level.
Check impedance of sensor.
Refer to the Service Manual for more
deta
ils.
P0544
ECM
Exhaust gas
temperature sensor
functional problem
Damaged sensor,
damaged circuit wires,
damaged connector or
damaged ECM output
pins
Check for approximately 2280
to 27
36 ohms at temperature of
19 to 21°C (66 to 70°F) between
system circuits A-H4 and A-J4.
Refe
r to the Service Manual for more
details.
204 smr2009-029

Похожие устройства

Скачать
Случайные обсуждения

Ответы 1

какой ресурс у турбины
9 лет назад