![Janome JemGold 2 [18/25] Раздел v декоративные строчки](/img/pdf.png)
Janome JemGold 2 [18/25] Раздел v декоративные строчки
![Janome JemGold 2 [18/25] Раздел v декоративные строчки](/views2/1144912/page18/bg12.png)
18
Шов-ракушка
Установки машины
1 Выбор строчки:
18
q w e
q w e
q
w
e
r
t
z
x
z
x
Shell Tuck
Machine setting:
q Stitch selector:
w Presser foot: Zigzag foot A
e Thread tension dial: 6-8
Use a lightweight fabric (tricot, for example). Fold the
fabric on the bias and stitch on the fold. Allow the needle
to just clear the folded edge to create a shelled edge. You
may need to increase the needle thread tension slightly.
If you sew rows of shell stitches, space the rows at least
5/8˝ (1.5 cm) apart. You can also sew shell stitches on
knits or soft silky woven fabrics, in any direction.
z Fold and stitch on the bias.
x When the needle swings to the right, allow the
needle to just clear the folded edge of the fabric
when it zigzags. After stitching, open the fabric
and iron to press the tacks flat to one side.
* If thread tension is too loose, tuck will not be
formed. Therefore, increase the tension and set it
between 6 to 8.
Blind Stitch Hemming
Machine setting:
q Stitch selector:
w Presser foot: Zigzag foot A
e Thread tension dial: 1-4
How to fold the fabric
On heavyweight fabrics that ravel, the raw edge should be
overcast first. Then fold the hem as illustrated.
q
Wrong side of fabric
w 0.4-0.7 cm (1/4˝-7/16˝)
e Overcasting stitch
How to sew
z Position the fabric on the machine so that the
needle just pierces the folded part of the fabric
when the needle comes over to the extreme left
side. Lower the presser foot.
Sew, while guiding the fabric so that the needle
catches the folded edge.
x If the needle drops on the left side too far, the
stitches appear on the right side of the fabric.
r Wrong side of fabric
t Right side of fabric
SECTION V DECORATIVE STITCHING
3
2
1
2 Прижимная лапка: Лапка А для зигзага
3 Натяжение нити: 6 – 8
Возьмите легкую ткань (например, трикотаж).
Сложите ткань и строчите по кромке. Игла
должна только обозначать сложенный край,
создавая ракушки. Возможно, потребуется
увеличить натяжение нити.
Если шить ряды ракушек, располагайте их на
расстоянии 1.5 см друг от друга. Можно также
шить ракушки на вязаном трикотаже или мягких
шелковых тканях в любом направлении.
1 Сложите ткань и прошейте по кромке.
2 Когда игла идет вправо, стежок зигзаг
должен едва захватывать складку. Затем
раскройте ткань и пригладьте складки на
одну сторону.
*
Если натяжение ослаблено, складки не
получатся. Поэтому увеличьте натяжение и
установите его в пределах от 6 до 8.
Потайная строчка
Установки машины
1 Выбор строчки:
18
q w e
q w e
q
w
e
r
t
z
x
z
x
Shell Tuck
Machine setting:
q Stitch selector:
w Presser foot: Zigzag foot A
e Thread tension dial: 6-8
Use a lightweight fabric (tricot, for example). Fold the
fabric on the bias and stitch on the fold. Allow the needle
to just clear the folded edge to create a shelled edge. You
may need to increase the needle thread tension slightly.
If you sew rows of shell stitches, space the rows at least
5/8˝ (1.5 cm) apart. You can also sew shell stitches on
knits or soft silky woven fabrics, in any direction.
z Fold and stitch on the bias.
x When the needle swings to the right, allow the
needle to just clear the folded edge of the fabric
when it zigzags. After stitching, open the fabric
and iron to press the tacks flat to one side.
* If thread tension is too loose, tuck will not be
formed. Therefore, increase the tension and set it
between 6 to 8.
Blind Stitch Hemming
Machine setting:
q Stitch selector:
w Presser foot: Zigzag foot A
e Thread tension dial: 1-4
How to fold the fabric
On heavyweight fabrics that ravel, the raw edge should be
overcast first. Then fold the hem as illustrated.
q
Wrong side of fabric
w 0.4-0.7 cm (1/4˝-7/16˝)
e Overcasting stitch
How to sew
z Position the fabric on the machine so that the
needle just pierces the folded part of the fabric
when the needle comes over to the extreme left
side. Lower the presser foot.
Sew, while guiding the fabric so that the needle
catches the folded edge.
x If the needle drops on the left side too far, the
stitches appear on the right side of the fabric.
r Wrong side of fabric
t Right side of fabric
SECTION V DECORATIVE STITCHING
3
2
1
2 Прижимная лапка: Лапка А для зигзага
3 Натяжение нити: 1 – 4
Как сложить ткань
У тяжелых тканей сначала необходимо
оверлочить срез. Затем сделайте складку как
показано на рисунке.
1 Изнаночная сторона
2 0,4 – 0,7 см
3 Оверлочный стежок
Как выполнить строчку
1 Расположите ткань на машине так, чтобы
игла в крайнем левом положении только
едва захватывала заложенную часть.
Опустите прижимную лапку.
Выполните строчку, направляя сложенный
край вдоль лапки.
2 Если игла заходит слишком далеко влево,
стежки будут видны на лицевой стороне
ткани.
4 Изнанка
5 Лицо
18
q w e
q w e
q
w
e
r
t
z
x
z
x
Shell Tuck
Machine setting:
q Stitch selector:
w Presser foot: Zigzag foot A
e Thread tension dial: 6-8
Use a lightweight fabric (tricot, for example). Fold the
fabric on the bias and stitch on the fold. Allow the needle
to just clear the folded edge to create a shelled edge. You
may need to increase the needle thread tension slightly.
If you sew rows of shell stitches, space the rows at least
5/8˝ (1.5 cm) apart. You can also sew shell stitches on
knits or soft silky woven fabrics, in any direction.
z Fold and stitch on the bias.
x When the needle swings to the right, allow the
needle to just clear the folded edge of the fabric
when it zigzags. After stitching, open the fabric
and iron to press the tacks flat to one side.
* If thread tension is too loose, tuck will not be
formed. Therefore, increase the tension and set it
between 6 to 8.
Blind Stitch Hemming
Machine setting:
q Stitch selector:
w Presser foot: Zigzag foot A
e Thread tension dial: 1-4
How to fold the fabric
On heavyweight fabrics that ravel, the raw edge should be
overcast first. Then fold the hem as illustrated.
q
Wrong side of fabric
w 0.4-0.7 cm (1/4˝-7/16˝)
e Overcasting stitch
How to sew
z Position the fabric on the machine so that the
needle just pierces the folded part of the fabric
when the needle comes over to the extreme left
side. Lower the presser foot.
Sew, while guiding the fabric so that the needle
catches the folded edge.
x If the needle drops on the left side too far, the
stitches appear on the right side of the fabric.
r Wrong side of fabric
t Right side of fabric
SECTION V DECORATIVE STITCHING
3
2
1
19
q w e
r
t
y
u
z
x c v
b
n
m
Buttonhole
Machine setting:
q Stitch selector:
w Presser foot: Buttonhole foot
e Thread tension dial: 1-5
* Before you sew the actual buttonholes on the
actual garment, make several trial buttonholes on
a fabric sample.
* Use interfacing on stretch fabrics.
z Select BH 1( ). Pull the slider so the top mark on
the slider aligns with the start mark. Draw both
threads to the left under the foot.
Insert the garment under the foot.
r
Start mark
x Lower the needle at the starting point. Then
lower the buttonhole foot.
Sew the required length of the left side of the button-
hole and stop the machine.
c Raise the needle to its highest position by turning
the handwheel, then select the BH 2,4( ).
Sew five bartack stitches and stop the machine.
v Raise the needle to its highest position and select
BH 3( ), sew the right side of buttonhole the
same length as the left side and stop the machine.
b Raise the needle and select the BH 2,4( ), and
sew five bartack stitches.
n Raise the needle and presser foot. Remove the fabric
from the machine. Cut both needle and bobbin threads
leaving approximately 10 cm (4˝) of thread ends
loose.
Draw the needle thread to the wrong side of the
fabric by pulling the bobbin thread. Then, knot the
threads.
m Place a pin just before the bartack to prevent cutting
bartack. Cut the opening with the seam ripper.
t
Seam ripper
• Corded buttonhole
1. With the buttonhole foot raised, hook the filler
cord on the spur
y at the back of the buttonhole
foot. Bring the ends toward you under the
buttonhole foot, clearing the front end.
Hook the filler cord into the forks
u on the front of
the buttonhole foot to hold them tight. Lower the
needle into the garment where the buttonhole
will start and lower the foot.
y
Spur
u Forks
2. Depress the foot control and sew the buttonhole over
the filler cord in the same way as described above.
3. Pull the left end of the filler cord to tighten it.
Thread the end of the cord through a darning
needle, draw it to the wrong side of the fabric and
cut.
РАЗДЕЛ V. ДЕКОРАТИВНЫЕ СТРОЧКИ
Содержание
- Важные инструкции по безопасности 1
- Внимание 1
- Дизайн и спецификация машины могут быть изменены 1
- Опасно 1
- Сохраняйте эти инструкции 1
- Names of parts 2
- Section i name of parts 2
- V дополнительные строчки 2
- Наименование частей 2
- Основные швейные техники 2
- Подготовка к шитью 2
- Раздел 2
- Раздел v декоративные строчки 2
- Содержание 2
- Уход за машиной 2
- Section i name of parts 3
- Наименование частей 3
- Раздел 3
- Connecting machine to power supply 4
- Controlling sewing speed 4
- Section ii getting ready to sew 4
- Standard accessories and storage place 4
- Стандартные аксессуары 4
- Connecting machine to power supply 5
- Controlling sewing speed 5
- Section ii getting ready to sew 5
- Контроль скорости шитья 5
- Подготовка к шитью 5
- Подключение питания к машине 5
- Раздел 5
- Changing needles 6
- How to drop the feed dog 6
- Note do not turn the pattern selector dial while the needle is in the fabric otherwise the needle may bend or break 6
- Pattern selection 6
- Place the selected presser foot so the pin on the foot lies just under the groove of the foot holder lower the presser bar to lock the foot in place 6
- Presser foot lifter 6
- Raise the needle turn the pattern selector dial to select the desired pattern 6
- Raise the presser foot press the lever on the back of the foot holder the presser foot will drop off 6
- Reverse stitch lever 6
- Selecting needle and thread 6
- The drop feed dog lever is located underneath the free arm bed on the back side of the machine 6
- The machine will sew in reverse while the reverse stitch lever is depressed 6
- The presser foot lifter raises and lowers the presser foot you can raise it about 0 cm 1 4 higher than the normal up position for easy removal of the presser foot or to help you place heavy fabric under the foot 6
- To attach and remove the presser foot 6
- To drop the feed dog slide the drop feed dog lever to the right q to raise the feed dog slide the drop feed dog lever to the left w and turn the handwheel toward you the feed dog must be up for normal sewing 6
- Выбор игл и ниток 6
- Смена игл 6
- How to drop the feed dog 7
- Pattern selection 7
- Presser foot lifter 7
- Reverse stitch lever 7
- To attach and remove the presser foot 7
- Выбор строчек 7
- Отключение транспортера ткани 7
- Прижимная лапка 7
- Реверс 7
- Рычаг подъема прижимной лапки 7
- For small spool 8
- Gently slide the hook cover plate release button q to the right and remove the cover plate w lift out the bobbin e 8
- Place the spool of thread on the spool pin with the thread coming off the spool as illustrated press the large spool holder q firmly against the spool of thread 8
- Preparation of the bobbin thread 8
- Removing the bobbin 8
- Set the spool 8
- Подготовка шпульной нити 8
- Attach the hook cover plate 10
- Check the threading by referring to the chart 10
- Continue to draw the thread lightly until the thread slips into notch b 10
- Guide the thread into the notch a 10
- In the bobbin holder 10
- Inserting the bobbin 10
- On the front side of the bobbin holder draw the thread to the left sliding it between the tension spring blades 10
- Place the bobbin 10
- Pull out about 15 cm 6 of thread 10
- Shown on the hook cover plat 10
- Threading the machine 10
- With the thread running off as illustrated 10
- Draw the thread down and slide the thread behind the needle bar thread guide t from the left 11
- Raise the presser foot with the presser foot lifter q lead the thread from the spool and pass it through the thread guide w then draw it down along the right slot 11
- Raise the take up lever to its highest position by turning the handwheel towards you firmly draw the thread from right to left over the take up lever r and down into the take up lever eye 11
- See page 12 11
- Then down around the thread guide plate e 11
- Threading the machine 11
- To set the needle thread 11
- Use the needle threader to thread the needle 11
- Заправка нити в машину 11
- Bring the bobbin thread up by pulling the needle thread as illustrated 13
- Drawing up the bobbin thread 13
- Pull 10 to 15 cm 4 to 6 of both threads back and under the presser foot 13
- Raise the presser foot and hold the needle thread lightly with your left hand 13
- Turn the handwheel slowly towards you one complete turn 13
- Section iii basic sewing 14
- Triple straight stitch 14
- Основные швейные техники 14
- Прямая строчка 14
- Раздел 14
- Triple straight stitch 15
- Прямой тройной стежок 15
- Balancing needle thread tension 16
- Choose the correct tension 16
- For straight stitch the ideal straight stitch will have threads locked between the two layers of the fabric as illustrated magnified to show detail if you look at the top and bottom of the seam you will notice that there are no gaps each stitch is smooth and even turn the dial to alter the needle thread tension the higher the number the tighter the tension 16
- Overcasting 16
- Results depend on stiffness and thickness of the fabric number of fabric layers type of stitch 16
- Section iv utility stitches 16
- Tension is too loose 16
- Tension is too tight 16
- The bobbin thread shows through on the right side of the fabric and it feels bumpy 16
- The needle thread shows through on the wrong side of the fabric and it feels bumpy 16
- Tricot stitch 16
- Turn the thread tension dial downwards to a larger number to tighten the needle thread tension 16
- Turn the thread tension dial upwards to a smaller number to loosen the needle thread tension 16
- Zigzag stitching 16
- Баланс натяжения верхней нити 16
- Section iv utility stitches 17
- V дополнительные строчки 17
- Зигзаг 17
- Обработка края 17
- Раздел 17
- Трикотажный стежок 17
- Blind stitch hemming 18
- Section v decorative stitching 18
- Shell tuck 18
- Раздел v декоративные строчки 18
- Buttonhole 19
- X c v b 19
- Изготовление петли 19
- Caution 20
- Q w e embroidery 20
- Section vi care of your machine 20
- Вышивка 20
- Caution 21
- Section vi care of your machine 21
- Меры предосторожности 21
- Раздел 21
- Уход за машиной 21
- Caution wait for the light bulb to cool down before touching it 22
- Insert the bobbin holder so that the knob fits next to the stopper in the race insert the bobbin 22
- Loosen the screw and remove the face plate 22
- Note when replacing the bulb unplug the machine 22
- Replace the needle plate inserting the two needle plate guide pins into the holes in the needle plate tighten the screw firmly with the screwdriver 22
- Replacing the bobbin holder 22
- Replacing the light bulb 22
- The sewing light is located behind the face plate 22
- To remove push and turn counterclockwise to replace push and turn clockwise 22
- To remove turn the bulb counterclockwise to replace turn the bulb clockwise 22
- Вероятная причина 23
- Неисправности машины 23
- Неисправность 23
- Примечание 23
Похожие устройства
- Janome 4852D Инструкция по эксплуатации
- Janome US2022 Инструкция по эксплуатации
- Janome US2014 Инструкция по эксплуатации
- InFocus IN8606HD Инструкция по эксплуатации
- InFocus IN8606HD Руководство QuickStart
- InFocus IN8606HD Брошюра с техническими характеристиками
- Jawbone JL06A-3RS1-EM Инструкция по эксплуатации
- Jawbone UP2 Light Grey (JL03-0101CFI-EM) Инструкция по эксплуатации
- Jawbone ERA Bronze (JC01-15-EM1) Инструкция по эксплуатации
- Jawbone ERA Black with Charge Case (JC03-03-EM1) Инструкция по эксплуатации
- Jawbone ERA Silver (JC01-01-EM1) Инструкция по эксплуатации
- Jawbone UP3 Red (JL04-0202ACE-EM) Инструкция по эксплуатации
- Jawbone UP2 Violet Circle (JL03-0453AEF-EM) Инструкция по эксплуатации
- Jawbone UP2 Turquoise Circle Rope (JL03-6666CEI-EM) Инструкция по эксплуатации
- Jawbone JL06A-3SS1-EM Инструкция по эксплуатации
- Jawbone UP3 INDIGO TWIST (JL04-6161ABD-EM) Инструкция по эксплуатации
- Pioneer FH-X720BT Руководство пользователя
- Jawbone BigJambox Graphite Hex (J2011-03-EMEA) Инструкция по эксплуатации
- Jawbone Jambox Blue Wave JBE06a-EMEA Инструкция по эксплуатации
- Ergomax MMA-220 Деталировка
Скачать
Случайные обсуждения