![Kramer TP-410 Руководства по эксплуатации онлайн [10/34] 139813](/img/pdf.png)
Kramer TP-410 Руководства по эксплуатации онлайн [10/34] 139813
![Kramer TP-410 Руководства по эксплуатации онлайн [10/34] 139813](/views2/1152888/page10/bga.png)
#
Feature
Function
21
RS-485 (G,B,A) Connect to the RS-485 controller.
Pins B (-) and A (+) are for RS-485; connect pin G to the cable shield (if required)
22
ETHERNET Connector Connects to the PC or other Serial Controller through computer networking
23
FLASH N/A (for factory use only)
24
FACTORY RESET
Turn the machine OFF using the power switch and then turn it ON while pressing the
FACTORY RESET button. The unit will power up and load its memory with the following
factory default definitions: default Ethernet settings (IP address: 192.168.1.39; TCP port
#: 5000 and UDP port #: 50000); RS-232 data is distributed to all 10 outputs and is
received by output 1 and the default EDID is acquired
25
SETUP DIP-switches For setup of the unit (see Section 7
26
)
Power Connector with Fuse AC connector enabling power supply to the unit
27
Power Switch Switch for turning the unit ON or OFF
7 TP-410 – Overview
Содержание
- Kramer electronics ltd 1
- Tp 410 uxga audio rs 232 line transmitter da 1
- User manual 1
- Contents 3
- Figures 3
- Introduction 4
- Achieving the best performance 5
- Getting started 5
- Overview 6
- Defining edid 7
- Defining the tp 410 uxga audio rs 232 line transmitter da 7
- Shielded twisted pair stp unshielded twisted pair utp 7
- Installing in a rack 11
- Connecting the tp 410 12
- Connecting to the tp 410 via an rs 232 connection 14
- Connecting to the tp 410 via an rs 485 connection 14
- Connecting the ethernet port directly to a pc crossover cable 15
- Connecting to the tp 410 via the ethernet 15
- The rear panel of the 15
- Connecting the ethernet port via a network hub straight through cable 16
- Ethernet port configuration 16
- Connecting several tp 410 units 17
- Configuration and distribution of control data 18
- Connecting a pc via rs 232 rs 485 18
- The local mode 18
- Connecting a pc via the ethernet 19
- Connecting multiple tp 410 units via the rs 485 bus 20
- The remote mode 20
- Setting the machine number 22
- The setup dip switches 22
- Eth configuration 23
- Setting the rs 232 rs 485 baud rate dip switches 23
- Be set to off 24
- Devices on the rs 485 bus must be terminated set to on all other devices must 24
- Setting the rs 485 bus termination 24
- The dip switch sets the rs 485 bus termination only the first and last physical 24
- Connectors 25
- Note that the cable ground shielding must be connected soldered to the connector shield 25
- This section defines the cat 5 pinout using a straight pin to pin cable with rj 45 25
- Wiring the cat 5 line in line out rj 45 connectors 25
- Wiring the cat 5 line in line out rj45 connectors 25
- Acquiring the edid 26
- Flash memory upgrade 27
- Technical specifications 28
- Communication parameters 29
- Default edid 30
- The factory default edid is listed below 30
- Below the data rate is set by the dip switches see section 7 31
- Data bits and 1 stop bit 31
- Destination instruction 31
- Kramer communication protocol 2000 31
- Machine number 31
- Output 31
- The rs 232 rs 485 protocol 2000 uses four bytes of information as shown 31
- Tp 410 kramer communication protocol 2000 31
- With no parity 8 31
- All the values in the table above are hexadecimal unless otherwise stated 32
Похожие устройства
- Kramer TP-185 Руководства по эксплуатации
- Rondell Geste RDA-111 Инструкция по эксплуатации
- Kramer TP-141 Руководства по эксплуатации
- Rondell Flamme RDS-339 Инструкция по эксплуатации
- Kramer TP-142 Руководства по эксплуатации
- Rondell RD-423 Инструкция по эксплуатации
- Rondell RDA-516 Инструкция по эксплуатации
- Kramer TP-145 Руководства по эксплуатации
- Rondell Champagne RDA-519 Инструкция по эксплуатации
- Kramer TP-146 Руководства по эксплуатации
- Kramer TP-300FW Руководства по эксплуатации
- Kramer TP-400FW Руководства по эксплуатации
- Kramer PT-561 Схема подключения
- Kramer PT-561 Руководства по эксплуатации
- Kramer PT-562 Схема подключения
- Kramer PT-562 Руководства по эксплуатации
- Kramer WP-561 Руководства по эксплуатации
- Kramer WP-562 Руководства по эксплуатации
- Rondell Heis RDS-100 Инструкция по эксплуатации
- Kramer PT-571HDCP Руководства по эксплуатации