Kramer TP-145 Руководства по эксплуатации онлайн
KRAMER ELECT RONIC S LTD.
USER MANUAL
MODELS:
TP-145
XGA/Audio/Data Line
Transmitter
TP-146
UXGA/Audio/Data Line
Receiver
P/N: 2900-000607 Rev 3
Содержание
- User manual 1
- Contents 3
- Figures 3
- Introduction 4
- Achieving the best performance 5
- Getting started 5
- Recycling kramer products 6
- Safety instructions 6
- Defining the tp 145 uxga audio data line transmitter 7
- Overview 7
- Button is pressed the tp 145 reads and stores the edid extended display 8
- Figure 1 defines the tp 145 uxga audio data line transmitter 8
- Identification data from the display device this prevents the problem whereby a 8
- Rs 232 interface allowing status requests and control of the destination unit 8
- Signals commands and data can flow in both directions simultaneously via the 8
- Source for example a pc fails to output video because it was not connected to 8
- Stream before transmission thus preserving the quality of the audio source 8
- The display device when attempting to read its edid 8
- When the tp 145 is connected to a display device and the edid capture 8
- 24 bit 48khz s pdif digital audio 9
- Analog audio signal a converted digital audio s pdif signal and bi directional 9
- Control virtually any device over a transmission range of up to 200m 660ft with a 9
- Defining the tp 146 uxga audio data line receiver 9
- Figure 2 defines the tp 146 uxga audio data line receiver 9
- In input the tp 146 outputs a computer graphics signal an unbalanced stereo 9
- Kramer tp 141 145 transmitter over tp cabling in addition the tp 146 features 9
- Level and equalization control for the uxga signal 9
- Rs 232 control commands and data the rs 232 interface makes it possible to 9
- Signal audio control data from the kramer tp 145 via tp cabling at its rj 45 line 9
- The capability to change the polarity of the vertical and horizontal sync signals 9
- The tp 146 is a high performance receiver that accepts the computer graphics 9
- Figure 3 defines the internal horizontal and vertical polarity switches of the 10
- Internal polarity and sync mode switches 10
- Next to the on led after setting the switches close the tp 146 10
- Note open the tp 146 unit to gain access to the hs and vs polarity and video 10
- Selection switches which are located on the lower part of the printed circuit board 10
- Tp 146 10
- Shielded twisted pair unshielded twisted pair 11
- Connecting the tp 145 tp 146 12
- Transmitting via rs 232 14
- Connectors 15
- Note that the cable ground shielding must be connected soldered to the connector shield 15
- This section defines the tp pinout using a straight pin to pin cable with rj 45 15
- Wiring the tp line in line out rj 45 connectors 15
- Acquiring the edid 16
- Technical specifications 17
Похожие устройства
- Rondell Champagne RDA-519 Инструкция по эксплуатации
- Kramer TP-146 Руководства по эксплуатации
- Kramer TP-300FW Руководства по эксплуатации
- Kramer TP-400FW Руководства по эксплуатации
- Kramer PT-561 Схема подключения
- Kramer PT-561 Руководства по эксплуатации
- Kramer PT-562 Схема подключения
- Kramer PT-562 Руководства по эксплуатации
- Kramer WP-561 Руководства по эксплуатации
- Kramer WP-562 Руководства по эксплуатации
- Rondell Heis RDS-100 Инструкция по эксплуатации
- Kramer PT-571HDCP Руководства по эксплуатации
- Kramer PT-572HDCP+ Руководства по эксплуатации
- Kramer PT-571 Руководства по эксплуатации
- Kramer PT-572+ Руководства по эксплуатации
- Kramer WP-306 Руководства по эксплуатации
- Kramer TP-575 Руководства по эксплуатации
- Kramer TP-573 Руководства по эксплуатации
- Kramer TP-574 Руководства по эксплуатации
- Kramer TP-576 Руководства по эксплуатации