Kramer TP-185 Руководства по эксплуатации онлайн
Содержание
- Kramer electronics ltd 1
- User manual 1
- Tables 3
- Getting started 4
- Introduction 4
- Getting started 5
- Quick start 5
- This quick start chart summarizes the basic setup and operation steps 5
- Overview 6
- Shielded twisted pair unshielded twisted pair 6
- Defining the tp 185 8 channel uxga audio rs 232 to cat 5 transmitter 7
- Defining the tp 185 8 channel uxga audio rs 232 to cat 5 transmitter 8
- Table 1 tp 185 front and rear panel features 8
- Installing the tp 185 in a rack 9
- Connecting and configuring the tp 185 10
- Connecting the tp 185 10
- Connecting to the tp 185 via an rs 232 connection 11
- Connecting to the tp 185 via an rs 485 connection 11
- Connecting multiple tp 185 units via the rs 485 bus 12
- Enabling and disabling the reply feature 13
- Setting the dip switches on the tp 185 13
- Setting the rs 485 bus termination 13
- Dip switches 2 3 and 4 set either the reply source in hardware mode table 2 or machine number in software mode table 3 14
- Figure 6 tp 185 reply source or machine number dip switches 14
- Note when there is more than one tp 185 attached to the rs 485 bus only one unit can have a reply path set 14
- Setting the dip switches on the tp 185 14
- Setting the reply source or machine number 14
- Table 2 hardware mode reply source dip switch setting 14
- Table 3 software mode rs 485 machine number dip switch setting 14
- When dip switch 1 is up reply is disabled default down on reply is enabled 14
- When there is more than one tp 185 attached to the rs 485 bus each unit must have a unique machine number 14
- Dip switch 8 sets the operating mode to either hardware or software mode 15
- Dip switches 5 6 and 7 set the serial port baud rate in both hardware and software modes according to table 4 note in a multiple device configuration all devices must be set to the same baud rate 15
- Figure 7 tp 185 baud rate dip switches 15
- Figure 8 tp 185 baud rate hardware software dip switch 15
- Hardware mode 15
- In hardware mode the rs 232 data is passed from any input to all outputs tp 185 routes the reply from the output port defined by the dip switches 2 3 and 4 see section 7 for reliable operation only one port can be defined 15
- Selecting hardware software mode 15
- Setting the dip switches on the tp 185 15
- Setting the rs 232 rs 485 baud rate dip switches 15
- Table 4 serial port baud rate dip switch setting 15
- When the dip switch is off the unit is set to hardware mode default on the unit is set to software mode 15
- Software mode 16
- Wiring the twisted pair rj 45 connectors 16
- Default communication parameters 17
- Lists the tp 185 default communication parameters 17
- Of the tp 185 17
- Table 6 technical specification 17
- Table 7 17
- Table 7 tp 185 communication parameters 17
- Technical specifications 17
- Technical specifications of the tp 185 are shown in table 6 17
- Default communication parameters 18
- Desti desti nation 18
- Instruction 18
- Kramer communication protocol 2000 18
- Machine number 18
- Msb lsb 18
- Output 18
- Table 8 protocol command definition 18
- The rs 232 rs 485 protocol 2000 uses four bytes of information as shown in table 8 the data rate is set by the dip switches see table 4 with no parity 8 data bits and 1 stop bit 18
- Command description reply 19
- Default communication parameters 19
- Description input output 19
- Instruction definition for specific instruction note 19
- Note all values in the table are hexadecimal unless otherwise stated notes on table 9 note 1 when the pc sends this command if the instruction is valid the unit replies by sending the pc the same 4 bytes that it was sent except for the first byte where the destination bit is set high note 2 if o6 0 tx this command defines reads the definition of the output 1 2 or3 to pass the rs 232 direct command from any input in this case the instruction does not modify previously set output numbers allowing the setting of multiple outputs for the direct command if o6 1 rx the command defines reads the definition of the output 1 2 or 3 to pass the reply from the output to inputs in this case the instruction resets a previously set output number preventing the setting of multiple outputs for the reply note 3 the reply to this command is as follows the same command and output codes as were sent are returned and the input is assigned the value of the parameter that was read the reply is per the definit 19
- Table 10 sample tp 185 control commands 19
- Table 9 instruction codes for the tp 185 19
- Caution 21
- For the latest information on our products and a list of kramer distributors visit 21
- Where updates to this user manual may be found we welcome your questions comments and feedback 21
Похожие устройства
- Rondell Geste RDA-111 Инструкция по эксплуатации
- Kramer TP-141 Руководства по эксплуатации
- Rondell Flamme RDS-339 Инструкция по эксплуатации
- Kramer TP-142 Руководства по эксплуатации
- Rondell RD-423 Инструкция по эксплуатации
- Rondell RDA-516 Инструкция по эксплуатации
- Kramer TP-145 Руководства по эксплуатации
- Rondell Champagne RDA-519 Инструкция по эксплуатации
- Kramer TP-146 Руководства по эксплуатации
- Kramer TP-300FW Руководства по эксплуатации
- Kramer TP-400FW Руководства по эксплуатации
- Kramer PT-561 Схема подключения
- Kramer PT-561 Руководства по эксплуатации
- Kramer PT-562 Схема подключения
- Kramer PT-562 Руководства по эксплуатации
- Kramer WP-561 Руководства по эксплуатации
- Kramer WP-562 Руководства по эксплуатации
- Rondell Heis RDS-100 Инструкция по эксплуатации
- Kramer PT-571HDCP Руководства по эксплуатации
- Kramer PT-572HDCP+ Руководства по эксплуатации