![Kramer TP-410 Руководства по эксплуатации онлайн [2/34] 139813](/img/pdf.png)
Kramer TP-410 Руководства по эксплуатации онлайн [2/34] 139813
![Kramer TP-410 Руководства по эксплуатации онлайн [2/34] 139813](/views2/1152888/page2/bg2.png)
Содержание
- Kramer electronics ltd 1
- Tp 410 uxga audio rs 232 line transmitter da 1
- User manual 1
- Contents 3
- Figures 3
- Introduction 4
- Achieving the best performance 5
- Getting started 5
- Overview 6
- Defining edid 7
- Defining the tp 410 uxga audio rs 232 line transmitter da 7
- Shielded twisted pair stp unshielded twisted pair utp 7
- Installing in a rack 11
- Connecting the tp 410 12
- Connecting to the tp 410 via an rs 232 connection 14
- Connecting to the tp 410 via an rs 485 connection 14
- Connecting the ethernet port directly to a pc crossover cable 15
- Connecting to the tp 410 via the ethernet 15
- The rear panel of the 15
- Connecting the ethernet port via a network hub straight through cable 16
- Ethernet port configuration 16
- Connecting several tp 410 units 17
- Configuration and distribution of control data 18
- Connecting a pc via rs 232 rs 485 18
- The local mode 18
- Connecting a pc via the ethernet 19
- Connecting multiple tp 410 units via the rs 485 bus 20
- The remote mode 20
- Setting the machine number 22
- The setup dip switches 22
- Eth configuration 23
- Setting the rs 232 rs 485 baud rate dip switches 23
- Be set to off 24
- Devices on the rs 485 bus must be terminated set to on all other devices must 24
- Setting the rs 485 bus termination 24
- The dip switch sets the rs 485 bus termination only the first and last physical 24
- Connectors 25
- Note that the cable ground shielding must be connected soldered to the connector shield 25
- This section defines the cat 5 pinout using a straight pin to pin cable with rj 45 25
- Wiring the cat 5 line in line out rj 45 connectors 25
- Wiring the cat 5 line in line out rj45 connectors 25
- Acquiring the edid 26
- Flash memory upgrade 27
- Technical specifications 28
- Communication parameters 29
- Default edid 30
- The factory default edid is listed below 30
- Below the data rate is set by the dip switches see section 7 31
- Data bits and 1 stop bit 31
- Destination instruction 31
- Kramer communication protocol 2000 31
- Machine number 31
- Output 31
- The rs 232 rs 485 protocol 2000 uses four bytes of information as shown 31
- Tp 410 kramer communication protocol 2000 31
- With no parity 8 31
- All the values in the table above are hexadecimal unless otherwise stated 32
Похожие устройства
- Kramer TP-185 Руководства по эксплуатации
- Rondell Geste RDA-111 Инструкция по эксплуатации
- Kramer TP-141 Руководства по эксплуатации
- Rondell Flamme RDS-339 Инструкция по эксплуатации
- Kramer TP-142 Руководства по эксплуатации
- Rondell RD-423 Инструкция по эксплуатации
- Rondell RDA-516 Инструкция по эксплуатации
- Kramer TP-145 Руководства по эксплуатации
- Rondell Champagne RDA-519 Инструкция по эксплуатации
- Kramer TP-146 Руководства по эксплуатации
- Kramer TP-300FW Руководства по эксплуатации
- Kramer TP-400FW Руководства по эксплуатации
- Kramer PT-561 Схема подключения
- Kramer PT-561 Руководства по эксплуатации
- Kramer PT-562 Схема подключения
- Kramer PT-562 Руководства по эксплуатации
- Kramer WP-561 Руководства по эксплуатации
- Kramer WP-562 Руководства по эксплуатации
- Rondell Heis RDS-100 Инструкция по эксплуатации
- Kramer PT-571HDCP Руководства по эксплуатации