![APC Smart-UPS SURT8000XLI [16/19] Roubleshooting](/img/pdf.png)
APC Smart-UPS SURT8000XLI [16/19] Roubleshooting
![APC Smart-UPS 10000VA SURT10000XLI [16/19] Roubleshooting](/views2/1159315/page16/bg10.png)
TROUBLESHOOTING
Use the table below to solve minor installation and operation problems. Refer to the APC Web site,
www.apc.com
for assistance with complex UPS problems.
PROBLEM AND POSSIBLE
C
AUSE
S
OLUTION
UPS WILL NOT TURN ON
Batteries are not connected
properly.
Check that the battery connectors are fully engaged.
button not pushed. Press the button once to power the UPS and the connected equipment.
UPS not connected to utility
power supply.
Check that the power cable from the UPS to the utility power supply is securely
connected at both ends.
Very low or no utility voltage. Check the utility power supply to ensure proper voltage at the receptacle.
UPS WILL NOT TURN OFF
button not pushed. Press the button once to turn the UPS off.
Internal UPS fault. Do not attempt to use the UPS. Unplug the UPS and have it serviced
immediately.
UPS BEEPS OCCASIONALLY
Normal UPS operation when
running on battery.
None. The UPS is protecting the connected equipment.
UPS DOES NOT PROVIDE EXPECTED BACKUP TIME
The UPS battery module(s) are
weak due to a recent outage or
are near the end of service life.
Charge the battery module(s). Modules require recharging after extended outages
and wear faster when put into service often or when operated at elevated
temperatures. If the battery module(s) are near the end of service life, consider
replacing, even if the Replace Battery LED is not illuminated.
FRONT PANEL LEDS FLASH SEQUENTIALLY
The UPS has been shut down
remotely through software or an
optional accessory card.
None. The UPS will restart automatically when utility power returns.
ALL LEDS ARE OFF AND THE UPS IS CONNECTED TO UTILITY POWER
The UPS is shut down and the
battery is discharged from an
extended outage.
None. The UPS will return to normal operation when the power is restored and
the battery has a sufficient charge.
BYPASS AND OVERLOAD LEDS ILLUMINATE, UPS EMITS A SUSTAINED ALARM TONE
The UPS is overloaded. The connected equipment exceeds the specified “maximum load” as defined in
Specifications on the APC Web site, www.apc.com
.
The alarm remains on until the overload is removed. Disconnect nonessential
equipment from the UPS to eliminate the overload condition.
14
Содержание
- 240 vac 1
- English 1
- Smart up 1
- Surt 8000 10000 va 1
- Tower rack mount 6u 1
- Uninterruptible power supply 1
- Installation 3
- Introduction 3
- Nstallation 3
- Removing the batteries 3
- Specifications 3
- Unpacking 3
- Hardwiring 4
- Install a utility circuit breaker in accordance with local electrical codes see tables below for input wiring 2 switch the ups input circuit breaker see a and utility circuit breakers off 3 remove the access panel see b 4 remove circular knockouts 5 run wires through access panel to terminal blocks wire to ground block first adhere to all national and local electrical codes see tables and graphics 4
- Recommended wire sizes are typical actual wire size must comply with required ampacity and local and national electrical codes 4
- Use appropriate strain relief on the hardwired input and output power cables 4
- Wiring must be performed by a qualified electrician 4
- Xlt xlj 4
- Xlt xlj xltw 5
- Installing and connecting the batteries and attaching the front bezel 6
- Circuit breakers 7
- Connecting power and equipment to the ups 7
- Options 7
- Basic connectors 8
- Epo terminal 8
- Ethernet port 8
- External battery pack connectors 8
- Serial port 8
- Tvss screw 8
- Bypass 9
- Description 9
- Front display panel 9
- Indicator 9
- On battery 9
- Online 9
- Operation 9
- Overload 9
- Peration 9
- Replace battery 9
- On battery operation 10
- Onfigurable 11
- Epo emergency power off option 13
- Terminal mode to configure ups parameters 14
- Aintenanc 15
- Arrant 15
- Ransporting 15
- Replacing the battery module s 15
- Transporting the ups 15
- Roubleshooting 16
- Use the table below to solve minor installation and operation problems refer to the apc web site www apc com for assistance with complex ups problems 16
- Limited warranty 18
- Service 18
- Apc worldwide customer support 19
- Arnings 19
- Requency 19
Похожие устройства
- APC Smart-UPS SUA5000RMI5U Инструкция по эксплуатации
- APC Back-UPS BE700G-RS Инструкция по эксплуатации
- APC Smart-UPS SURT2000XLI Инструкция по эксплуатации
- APC Smart-UPS SC620I Инструкция по эксплуатации
- APC Smart-UPS 10000VA SURT10000XLI Инструкция по эксплуатации
- Aquael easyheater 25w Инструкция по эксплуатации
- Aquael easyheater 50w Инструкция по эксплуатации
- Aquael easyheater 75w Инструкция по эксплуатации
- Aquael easyheater 100w Инструкция по эксплуатации
- Aquael easyheater 150w Инструкция по эксплуатации
- Aquael comfort zone gold 50w Инструкция по эксплуатации
- Aquael comfort zone gold 75w Инструкция по эксплуатации
- Aquael comfort zone gold 100w Инструкция по эксплуатации
- Sony HT-XT100//C Инструкция по эксплуатации
- Sony CDX-G1003ER Инструкция по эксплуатации
- Sony SAL1635Z2 Инструкция по эксплуатации
- Sony STR-DN860//M Инструкция по эксплуатации
- Sony STR-DN1060/M Инструкция по эксплуатации
- Sony MEX-XB100BT Инструкция по эксплуатации
- Sony LCS-AMB Инструкция по эксплуатации
Скачать
Случайные обсуждения
Ответы 0
ИБП запустился, потом подали сеть, а он все от батарей работает, в чем причина?
6 лет назад