![Makita ga5021c [9/16] Assembly](/img/pdf.png)
Makita ga5021c [9/16] Assembly
![Makita ga5021c [9/16] Assembly](/views2/1175225/page9/bg9.png)
9
Indication lamp
1
008416
The indication lamp lights up green when the tool is
plugged. If the indication lamp does not light up, the
mains cord or the controller may be defective. The
indication lamp is lit but the tool does not start even if
the tool is switched on, the carbon brushes may be
worn out, or the controller, the motor or the ON/OFF
switch may be defective.
Unintentional restart proof
Even locking lever keeping the switch trigger depressed
(Lock-on position) does not allow the tool to restart even
when the tool is plugged.
At this time, the indication lamp flickers red and shows
the unintentional restart proof device is on function.
To cancel the unintentional restart proof, pull the switch
trigger fully, then release it.
ASSEMBLY
CAUTION:
• Always be sure that the tool is switched off and
unplugged before carrying out any work on the
tool.
Installing side grip (handle)
CAUTION:
• Always be sure that the side grip is installed
securely before operation.
007993
Screw the side grip securely on the position of the tool
as shown in the figure.
Installing loop handle (Optional accessory)
CAUTION:
• Always be sure that the loop handle is installed
securely before operation.
1
2
008049
Always install the loop handle on the tool before
operation. Hold the tool's switch handle and the loop
handle firmly with both hands during operation.
Install the loop handle so that its protrusion will fit into
the matching hole in the gear housing.
Install the bolts and tighten them with the hex wrench.
The loop handle can be installed in two different
directions as shown in the figures whichever is
convenient for your work.
1
2
3
008047
1
2
3
008048
Installing or removing wheel guard (For
depressed center wheel, multi disc / abrasive
cut-off wheel, diamond wheel)
CAUTION:
• When using a depressed center grinding
wheel/Multi-disc, wire wheel brush or cut-off wheel,
the wheel guard must be fitted on the tool so that
the closed side of the guard always points toward
the operator.
1. Loop handle
2. Hex wrench
3. Bolt
1. Loop handle
2. Hex wrench
3. Bolt
1. Protrusion of
loop handle
2. Matching hole
in gear housing
1. Indication lamp
Содержание
- Angle grinder 1
- Specifications 2
- Symbols 2
- Ec declaration of conformity 3
- General power tool safety warnings 3
- Save all warnings and instructions for future reference 3
- Grinder safety warnings 5
- Save these instructions 7
- Warning 7
- Constant speed control for models ga5020c ga5021c ga6020c ga6021c 8
- Electronic function 8
- Functional description 8
- Shaft lock 8
- Soft start feature 8
- Switch action 8
- Assembly 9
- Installing loop handle optional accessory 9
- Installing or removing wheel guard for depressed center wheel multi disc abrasive cut off wheel diamond wheel 9
- Installing side grip handle 9
- Installing or removing depressed center grinding wheel multi disc optional accessory 10
- Operation 10
- Grinding and sanding operation 11
- Mm 4 1 2 125 mm 5 150 mm 6 11
- Operation with abrasive cut off diamond wheel optional accessory 11
- Maintenance 12
- Optional accessories 12
- Replacing carbon brushes 12
- Anjo aichi japan 16
- Makita corporation 16
- Www makita com 16
Похожие устройства
- ШТРИХ–М ШТРИХ-ФР-К Ремонтная документация
- ШТРИХ–М ШТРИХ-ФР-К OPOS Драйвер 1.7.10
- Makita ga4530 Инструкция по эксплуатации
- ШТРИХ–М Retail-01 Инструкция по эксплуатации
- ШТРИХ–М Retail-01 Ремонтная документация
- Makita hr2600 Инструкция по эксплуатации
- Makita hr1830 Инструкция по эксплуатации
- Makita td0101 Инструкция по эксплуатации
- Makita hp1631 Инструкция по эксплуатации
- Makita uh4861 Инструкция по эксплуатации
- ШТРИХ–М ШТРИХ-950К Инструкция по эксплуатации
- ШТРИХ–М Retail-01K Инструкция по эксплуатации
- Makita uh4261 Инструкция по эксплуатации
- ШТРИХ–М Retail-01K Ремонтная документация
- Makita elm3711 Инструкция по эксплуатации
- Makita elm3311 Инструкция по эксплуатации
- ШТРИХ–М ШТРИХ-ПРИНТ ФI Инструкция по эксплуатации
- ШТРИХ–М ШТРИХ-ПРИНТ ФI Ремонтная документация
- ШТРИХ–М ШТРИХ-ПРИНТ ФI Руководство администратора
- ШТРИХ–М ШТРИХ-ПРИНТ М Инструкция по эксплуатации