TELEOFIS RX600-R2 [462/717] Remote host port 1 5535 note after sring that indicates incoming udp data and issuing srecv to receive data itself through ss is possible to check last remote host ip port note if successive resume of the socket to online mode is performed so connection with first remote host is restored as it was before note the maximum number of bytes to send is 1472 bytes

Every command issued to the telit modules returns a result response if response codes are enabled default the time needed to process the given command and return the response varies depending on the command type commands that do not interact with the sim or the network and only involve internal setups or readings have an immediate response commands that interact with the sim or the network could take many seconds to send a response depending on sim configuration e g number of contacts stored in the phonebook number of stored sms or on the network the command may interact with in the table below are listed only the commands whose interaction with the sim or the network could lead to long response timings when not otherwise specified timing is referred to set command for phonebook and sms writing and reading related commands timing is referred to commands issued after phonebook sorting is completed for dtmf sending and dialling commands timing is referred to module registered on network 31

Cmgs 60 after ctrl z for sms not concatenated 32

Cmgw 5 after ctrl z for sms not concatenated 1 32

Prompt 32

Command issuing timing 34

This may happen if only a or at are sent to the at port it does not happen if at at at etc are sent to the at port 34

Factory profile and user profiles 35

Storage 35

The values set by following commands are automatically stored in nvm without issuing any storing command and independently from the profile unique values and are automatically restored at startup 36

The values set by following commands are stored in the profile extended section and if the newer at command interface style has been selected see selint 2 they depend on the specific at instance see cmux 36

The values set by following commands are stored in the profile extended section and they don t depend on the specific at instance see cmux 36

The values set by following commands are stored in nvm on demand issuing specific commands and independently from the profile 37

At commands availability table 38

At commands reference guide 38

Software version applicable products 38

St10025a rev 24 2016 09 07 38

The following table lists the at commands set and matches the availability of every single command with the telit module by means of the software version as showed on the table above 38

The following table shows the link software version product it is used jointly with the second reported table to verify if the selected at command is supported by the couple software version product 38

At commands reference guide 39

St10025a rev 24 2016 09 07 39

At commands reference guide 40

St10025a rev 24 2016 09 07 40

At commands reference guide 41

St10025a rev 24 2016 09 07 41

At commands reference guide 42

Command available only on ge864 quad and gc864 quad gl865 dual gl865 quad and gl868 dual 42

Not available on gl865 dual gl865 dual v3 gl865 quad v3 gl868 dual gl868 dual v3 gl865 quad ge910 quad v3 and ge866 quad 42

St10025a rev 24 2016 09 07 42

At commands reference guide 43

Available only on ge864 quad ge864 quad v2 gc864 quad and gc864 quad v2 43

Not available for gc864 dual gc864 dual v2 ge864 dual v2 gl865 dual gl865 dual v3 gl868 dual and gl868 dual v3 43

St10025a rev 24 2016 09 07 43

At commands reference guide 44

Only available on gl865 quad gl865 dual gl865 dual v3 gl865 quad v3 gl868 dual v3 gl868 dual and ge866 quad 44

St10025a rev 24 2016 09 07 44

At commands reference guide 45

St10025a rev 24 2016 09 07 45

At commands reference guide 46

St10025a rev 24 2016 09 07 46

At commands reference guide 47

Python is a registered trademark of the python software foundation 47

St10025a rev 24 2016 09 07 47

At commands reference guide 48

Available only on gl865 dual v3 gl865 quad v3 gl868 dual v3 ge910 quad v3 ge866 quad ge910 quad and ge910 gnss 48

Not available for gc864 dual gc864 dual v2 ge864 dual v2 gl865 dual and gl868 dual 48

Not available on ge865 quad gl865 dual gl865 dual v3 gl865 quad v3 gl868 dual gl868 dual v3 gl865 quad ge910 quad v3 and ge866 quad 48

St10025a rev 24 2016 09 07 48

At commands reference guide 49

Available only on gl865 dual v3 gl865 quad v3 gl868 dual v3 ge910 quad v3 and ge866 quad 49

Not available on ge864 quad and gc864 quad 49

St10025a rev 24 2016 09 07 49

At commands reference guide 50

St10025a rev 24 2016 09 07 50

At commands reference guide 51

St10025a rev 24 2016 09 07 51

At commands references 52

Command line general format 52

Command line prefixes 52

General configuration commands 52

At commands reference guide 53

St10025a rev 24 2016 09 07 53

The following table shows which at commands interface can be applied and is default for the specific product 53

Hayes compliant at commands 55

3gpp ts 27 07 at commands 88

Cfun set phone functionality 135

Cfun set phone functionality 136

At cpin test command returns ok result code 139

Be given 139

Command 139

Cpin enter pin selint 0 1 139

Example 139

Note what follows is a list of the commands which are accepted when me is pending sim pin or sim puk 139

Password to be given 139

Ph sp pin me is waiting service provider personalization password to be given ph sp puk me is waiting service provider personalization unblocking password to be given ph corp pin me is waiting corporate personalization password to be given ph corp puk me is waiting corporate personalization unblocking password to 139

All the above commands but the ones in the grayed cells can be issued even if the sim card is not inserted yet all the above commands but csdh and cnmi can be issued even if me is waiting for phone to sim card password to be given 140

Cpin enter pin cpin enter pin selint 2 140

Cpin enter pin selint 0 1 140

Reference 3gpp ts 27 07 140

String type value to check the status of the pin request use the command at cpin 140

Cpin enter pin selint 2 142

3gpp ts 27 05 at commands for sms and cbs 202

At commands reference guide 229

Cmgl list messages selint 0 1 229

Cnmi new message indications to terminal equipment selint 2 229

In different sessions 229

Is the memory where the received messages are stored see cpms 229

Is the message storage for read and delete sms as last settings of command cpms the parameter type and the command output depend on the last settings of command cmgf message format to be used pdu mode 229

List messages cmgl 229

No urc is shown on any session and no status report is stored on sim 229

Parameter 229

St10025a rev 24 2016 09 07 229

The sm is not stored 229

Urc cds is shown only on session 0 and no status report is stored on 229

Fax class 1 at commands 269

Custom at commands 275

At commands reference guide 280

Ceernet ext error report for network reject cause selint 2 280

Notes codes from 2 to 8 are hard mm gmm reject causes according with 3gpp when these causes are used by the mno the sim shall be considered as invalid for non gprs services and or gprs services until switching off or the sim is 280

St10025a rev 24 2016 09 07 280

Test command returns ok result code 289

Enables call monitoring function with calling number display when enabled 329

Parameters 374

At commands reference guide 385

Note if the value is set to 99 the pcl is managed by network note the set values aren t stored in nvm note if the network requires a pcl value the module will use the pclfix value instead note this is not compliant to etsi specifications note this command inhibits at pclmin settings note the different power control levels pcl shall have the nominal output power as defined in the table below these tables are extracted from 3gpp etsi ts 145 005 v4 9 2010 07 385

St10025a rev 24 2016 09 07 385

At commands reference guide 386

At pclfix test command reports the supported range of parameters values 386

At pclmin pclg set command sets the minimum pcl power control level 386

Pcl minimum pclmin 386

Pclmin pcl minimum selint 0 1 2 386

Pcs1900 386

St10025a rev 24 2016 09 07 386

At commands reference guide 387

Numeric parameter indicating the minimum pcl for pcs band range 0 15 default 0 note the set values are stored in nvm note if the network requires a pcl lower than pclmin value the module will use the pclmin value instead and so it will use less power in transmission this is not compliant to etsi specifications note if the command pclfix is issued then the command pclmin is inhibited note this command is not compliant to etsi specifications note the different power control levels pcl shall have the nominal output power as defined in the table below these tables are extracted from 3gpp etsi ts 145 005 v4 9 2010 07 387

St10025a rev 24 2016 09 07 387

At commands reference guide 388

St10025a rev 24 2016 09 07 388

Tcpatrunaut 401

Tcpatrunfrw 403

Tcpatrunaut 404

Tcpatrunaut 405

Scfgext socket configuration extended 440

Data represented as text default 1 data represented as sequence of hexadecimal numbers from 00 to ff each octet of the data is given as two ira character long hexadecimal number 441

Scfgext2 socket configuration extended 2 442

Srecv receive data in command mode 451

Srecv receive data in command mode 452

The response format is 453

Are cleared when the socket itself is connected again sd or sa after sl until then if previous connection has been established and closed old values are yet available 454

Example example 462

Remote host port 1 5535 note after sring that indicates incoming udp data and issuing srecv to receive data itself through ss is possible to check last remote host ip port note if successive resume of the socket to online mode is performed so connection with first remote host is restored as it was before note the maximum number of bytes to send is 1472 bytes 462

The response format is 464

Contained in the payload 467

Afterward a no carrier indication is sent when the socket is closed 470

Afterward a no carrier indication is sent when the socket is closed 471

Afterward a no carrier indication is sent when the socket is closed 478

Change is forbidden during an open ftp connection with or without security furthermore ssl 484

Configuration settings are forbidden during ftps connections 484

Qdns query dns 493

Easy script extension pytho 575

Interpreter at commands 575

Max number of bytes to read at a time 601

Maxbyte 601

And waits for the data to send when 603

Bytes have been sent operation is automatically completed if data are successfully sent then the response is 603

And waits for the data to send when 605

Bytes have been sent operation is automatically completed if data are successfully sent then the response is 605

Setting is saved into teseoii nvm and retained until a nvm erase or a next firmware upgrade of the gnss receiver is performed 613

Gpsacp get acquired position 622

Gpsacp get acquired position 623

The command is available in controlled mode only 637

0 9 a d dtmf tone g l user defined tone 652

0 9 a d dtmf tone g l user defined tones 652

Tsvol tone classes volume selint 2 654

Z b z b z a z a a z h 658

Z h z h 658

Z b z b z a z a a z h 659

Z h z h 659

Z b z b z a z a a z h 660

Z h z h 660

At dvi 2 1 1 ok 671

Reproduce pcm stream from serial to selected path 2 send speech from selected path to serial 673

Note feature supported only in idle mode note the format of mono pcm audio file is 8k samples sec and 16 bits sample 678

In asize note below 200 kb of free space the file system could stop the recording and no more recordings are allowed 679

Sslcfg 1 1 0 1500 0 65535 10 5000 0 255 0 2 0 2 0 0 690

Note before opening a ssl connection the gprs context must have been activated by at sgact 1 1 note before opening a ssl connection make sure to have stored the needed secure data certificate ca certificate private key using at sslsecdata for the security level set through at sslseccfg 692

Note before opening a ssl connection the gprs context must have been activated by at sgact x 1 note if an error occurs during reconnection the socket can not be reconnected and then a new connection has to be done note if the remote server cleans sessionid cache before 693

Is not set the value set into at ssld is used 694

Reconnection the full handshake will be made 694

Note before opening a ssl connection the gprs context must have been activated by at sgact x 1 note if an error occur during reconnection the socket can not be reconnected then a new connection has to be done 695

Is not enabled 696

At sslsecdata 699

No data stored ok 699

And waits for the data to send to complete the operation send ctrl z char 0x1a hex to exit without writing the message send esc char 0x1b hex if data are successfully sent then the response is ok if data sending fails for some reason an error code is reported 700

Note before sending data through the ssl connection it has to be established using at ssld 700

Note before sending data through the ssl connection it has to be established using at ssld note all special characters are sent like a generic byte 701

At dwstatus test command reports ok result code 704

Number of bytes sent 704

Send data to m2m service dwsend 704

Bytes have been sent operation is automatically 705

Dwsendr send raw data to m2m service selint 2 705

Send raw data to devisewise server dwsendr 705

Greenwich mean time 710

List of acronyms 710

Document history 712

Содержание

Похожие устройства