![Graco Pro-Shot 242056 [2/6] Warnings](/img/pdf.png)
Graco Pro-Shot 242056 [2/6] Warnings
![Graco Pro-Shot 24H402 [2/6] Warnings](/views2/1193162/page2/bg2.png)
Warnings
2 309032L
Warnings
The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclama-
tion point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. When
these symbols appear in the body of this manual or on warning labels, refer back to these Warnings. Product-specific
hazard symbols and warnings not covered in this section may appear throughout the body of this manual where
applicable.
WARNING
EQUIPMENT MISUSE HAZARD
Misuse can cause death or serious injury.
• Do not operate the unit when fatigued or under the influence of drugs or alcohol.
• Do not exceed the maximum working pressure or temperature rating of the lowest rated system com-
ponent. See Technical Data in all equipment manuals.
• Use fluids and solvents that are compatible with equipment wetted parts. See Technical Data in all
equipment manuals. Read fluid and solvent manufacturer’s warnings. For complete information
about your material, request MSDS from distributor or retailer.
• Turn off all equipment and follow the Pressure Relief Procedure when equipment is not in use.
• Check equipment daily. Repair or replace worn or damaged parts immediately with genuine manu-
facturer’s replacement parts only.
• Do not alter or modify equipment. Alterations or modifications may void agency approvals and create
safety hazards.
• Make sure all equipment is rated and approved for the environment in which you are using it.
• Use equipment only for its intended purpose. Call your distributor for information.
• Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.
• Do not kink or over bend hoses or use hoses to pull equipment.
• Keep children and animals away from work area.
• Comply with all applicable safety regulations.
SKIN INJECTION HAZARD
High-pressure fluid from dispensing device, hose leaks, or ruptured components will pierce skin. This
may look like just a cut, but it is a serious injury that can result in amputation. Get immediate surgical
treatment.
• Do not point dispensing device at anyone or at any part of the body.
• Do not put your hand over the fluid outlet.
• Do not stop or deflect leaks with your hand, body, glove, or rag.
• Follow the Pressure Relief Procedure when you stop dispensing and before cleaning, checking, or
servicing equipment.
• Tighten all fluid connections before operating the equipment.
• Check hoses and couplings daily. Replace worn or damaged parts immediately.
TOXIC FLUID OR FUMES HAZARD
Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin, inhaled, or
swallowed.
• Read MSDSs to know the specific hazards of the fluids you are using.
• Store hazardous fluid in approved containers, and dispose of it according to applicable guidelines.
• Always wear chemically impermeable gloves when spraying, dispensing, or cleaning equipment.
Содержание
- Grease dispense valve 1
- Instructions 1
- Pro sho 1
- Warning 2
- Warnings 2
- Adjustment 3
- Operation 3
- Pressure relief procedure 3
- Back off nut approxi mately 1 8 turn hold bottom nut in place and securely tighten top nut 4
- Check all parts thoroughly when disassembling and carefully replace any worn or damaged parts 4
- Disassembly 4
- For specific operational problems see trouble shooting 4
- If additional adjustment is desired follow adjustment procedure on page 3 4
- Push plunger rod 15 through seal 4 be careful seat 14 ball 2 and copper gasket 6 will fall out bottom 4
- Reassemble valve 4
- Refer to parts drawing page 5 for following instruc tions 4
- Relieve the pressure see pressure relief proce dure on page 3 4
- Remove acorn nuts 1 and bolts 17 from trigger guard 12 remove trigger guard 12 4
- Remove bottom seat adapter 10 from grease fun body 9 4
- Remove hex nuts 5 4
- Remove outlet adapter 7 4
- Remove rod guide 18 from grease gun body 9 4
- Remove yoke 16 4
- Replace all parts included in service kit 243446 4
- Service 4
- To reduce the risk of serious injury after servicing valve always make sure the valve is in the closed position with trigger released 4
- Troubleshooting 4
- With trigger in free position tighten bottom nut 5 until yoke bottoms out on rod guide this is the max imum flow setting 4
- Technical data 5
- Copyright 1999 graco inc all graco manufacturing locations are registered to iso 9001 www graco com revised december 2012 6
- For the latest information about graco products visit www graco com 6
- Graco headquarters minneapolis international offices belgium china japan korea 6
- Graco inc and subsidiaries p o box 1441 minneapolis mn 55440 1441 usa 6
- Graco information 6
- Graco standard warranty 6
- To place an order contact your graco distributor or call to identify the nearest distributor phone 612 623 6928 or toll free 1 800 533 9655 fax 612 378 3590 6
Похожие устройства
- Graco Pro-Shot 242056 Сервис мануал
- Graco Pro-Shot 242057 Инструкция по эксплуатации
- Graco Pro-Shot 242057 Сервис мануал
- Graco Pro-Shot 242058 Инструкция по эксплуатации
- Graco Pro-Shot 242058 Сервис мануал
- Graco Pro-Shot 24H399 Инструкция по эксплуатации
- Graco Pro-Shot 24H399 Сервис мануал
- Graco Pro-Shot 24H400 Инструкция по эксплуатации
- Graco Pro-Shot 24H400 Схема сборки
- Graco Pro-Shot 24H401 Инструкция по эксплуатации
- Graco Pro-Shot 24H401 Схема сборки
- Graco Pro-Shot 24H402 Инструкция по эксплуатации
- Graco Pro-Shot 24H402 Схема сборки
- Graco Pro-Shot 24H403 Инструкция по эксплуатации
- Graco Pro-Shot 24H403 Схема сборки
- Graco Pro-Shot 24H404 Инструкция по эксплуатации
- Graco Pro-Shot 24H404 Схема сборки
- Graco Pro-Shot 24H405 Инструкция по эксплуатации
- Graco Pro-Shot 24H405 Схема сборки
- Graco Pro-Shot 24H406 Инструкция по эксплуатации