![Moxa EDS-P510 — communication Redundancy STP RSTP MSTP Configuration Guide [32/36]](/img/pdf.png)
Moxa EDS-P510 — communication Redundancy STP RSTP MSTP Configuration Guide [32/36]
![Moxa TN-5818-2GTXBP-HV-HV-T [32/36] Communication redundancy stp rstp mstp](/views2/1196347/page32/bg20.png)
Communication Redundancy STP/RSTP/MSTP
4-7
At the top of this page, the user can check the Current Status of this function. For RSTP, you will see:
Now Active:
It shows which communication protocol is being used—Turbo Ring, RSTP, or neither.
Root/Not Root
This field only appears when RSTP mode is selected. The field indicates whether or not this switch is the Root
of the Spanning Tree (the root is determined automatically).
At the bottom of this page, the user can configure the Settings of this function. For RSTP, you can configure:
Redundancy Protocol
Setting
Description
Factory Default
Turbo Ring
Select this item to change to the Turbo Ring configuration page.
None
RSTP (IEEE
802.1W/1D)
Select this item to change to the RSTP configuration page.
None
Bridge priority
Setting
Description
Factory Default
Numerical value
selected by user
Increase this device’s bridge priority by selecting a lower
number. A device with a higher bridge priority has a greater
chance of being established as the root of the Spanning Tree
topology.
32768
Forwarding Delay (sec.)
Setting
Description
Factory Default
Numerical value input
by user
The amount of time this device waits before checking to see if it
should change to a different state.
15
Hello time (sec.)
Setting
Description
Factory Default
Numerical value input
by user
The root of the Spanning Tree topology periodically sends out a
“hello” message to other devices on the network to check if the
topology is healthy. The “hello time” is the amount of time the
root waits between sending hello messages.
2
Max. Age (sec.)
Setting
Description
Factory Default
Numerical value input
by user
If this device is not the root, and it has not received a hello
message from the root in an amount of time equal to “Max.
Age,” then this device will reconfigure itself as a root. Once two
or more devices on the network are recognized as a root, the
devices will renegotiate to set up a new Spanning Tree
topology.
20
Enable STP per Port
Setting
Description
Factory Default
Enable/Disable
Select to enable the port as a node on the Spanning Tree
topology.
Disabled
NOTE
We suggest not enabling the Spanning Tree Protocol once the port is connected to a device (PLC, RTU, etc.) as
opposed to network equipment. The reason is that it will cause unnecessary negotiation.
Содержание
- User s manual p.1
- Communication redundancy p.1
- Www moxa com product p.1
- Fourth edition march 2015 p.1
- Trademarks p.2
- Technical support contact information p.2
- Disclaimer p.2
- Copyright notice p.2
- Communication redundancy p.2
- Www moxa com support p.2
- User s manual p.2
- Table of contents p.3
- Redundancy p.4
- Introduction to communication p.4
- Gigabit ethernet redundant ring capability 50 ms p.5
- Communication redundancy introduction to communication redundancy p.5
- Turbo ring p.6
- When the number of switches in the turbo ring is even p.7
- The turbo ring concept p.7
- Setting up turbo ring or turbo ring v2 p.7
- Determining the redundant path of a turbo ring ring p.7
- Communication redundancy turbo ring p.7
- Determining the redundant path of a turbo ring v2 ring p.8
- Communication redundancy turbo ring p.8
- Attention p.8
- When the number of switches in the turbo ring is odd p.8
- Ring coupling configuration p.8
- Ring coupling for a turbo ring v2 ring p.9
- Ring coupling for a turbo ring ring p.9
- Communication redundancy turbo ring p.9
- Attention p.9
- Turbo ring v2 p.10
- Dynamic ring coupling drc configuration applies only to p.10
- Dual ring for a turbo ring v2 ring p.11
- Dual ring configuration applies only to turbo ring v2 p.11
- Communication redundancy turbo ring p.11
- Attention p.11
- Dual homing configuration applies only to turbo ring v2 p.12
- Configuring turbo ring and turbo ring v2 p.12
- Configuring turbo ring p.12
- Communication redundancy turbo ring p.12
- Explanation of settings items p.13
- Explanation of current status items p.13
- Communication redundancy turbo ring p.13
- Communication redundancy turbo ring p.14
- Explanation of current status items p.15
- Configuring turbo ring v2 p.15
- Communication redundancy turbo ring p.15
- Explanation of settings items p.16
- Communication redundancy turbo ring p.16
- Communication redundancy turbo ring p.17
- Communication redundancy turbo ring p.18
- Explanation of ring status items p.19
- Configuring turbo ring v2 with dynamic ring coupling p.19
- Communication redundancy turbo ring p.19
- Explanation of drc status items p.20
- Communication redundancy turbo ring p.20
- Explanation of ring settings items p.20
- Turbo chain p.21
- The turbo chain concept p.22
- Setting up turbo chain p.22
- Communication redundancy turbo chain p.22
- Tail switch configuration p.23
- Member switch configuration p.23
- Head switch configuration p.23
- Explanation of current status items p.23
- Configuring turbo chain p.23
- Communication redundancy turbo chain p.23
- Explanation of settings items p.24
- Communication redundancy turbo chain p.24
- Communication redundancy turbo chain p.25
- Stp rstp mstp p.26
- Communication redundancy stp rstp mstp p.27
- What is stp p.27
- The stp rstp mstp concept p.27
- Stp requirements p.28
- How stp works p.28
- Communication redundancy stp rstp mstp p.28
- Stp reconfiguration p.29
- Stp configuration p.29
- Stp calculation p.29
- Differences between stp rstp and mstp p.29
- Communication redundancy stp rstp mstp p.29
- Stp example p.30
- Communication redundancy stp rstp mstp p.30
- Using stp on a network with multiple vlans p.31
- Configuring stp rstp p.31
- Communication redundancy stp rstp mstp p.31
- Communication redundancy stp rstp mstp p.32
- Configuring mstp p.33
- Communication redundancy stp rstp mstp p.33
- Communication redundancy stp rstp mstp p.34
- Communication redundancy stp rstp mstp p.35
- Configuration limits of stp rstp p.36
- Communication redundancy stp rstp mstp p.36
Похожие устройства
-
Moxa EDS-G512E-8PoE-4GSFP-TТехнические характеристики -
Moxa EDS-G512E-8PoE-4GSFP-TРуководство по созданию резервированных сетей -
Moxa EDS-G512E-8PoE-4GSFP-TРуководство по использованию командной строки -
Moxa EDS-G512E-8PoE-4GSFP-TРуководство по аппаратной части -
Moxa EDS-G512E-8PoE-4GSFP-TИнструкция по эксплуатации -
Moxa EDS-G512E-8PoE-4GSFPТехнические характеристики
-
Moxa EDS-G512E-8PoE-4GSFPРуководство по созданию резервированных сетей
-
Moxa EDS-G512E-8PoE-4GSFPРуководство по использованию командной строки
-
Moxa EDS-G512E-8PoE-4GSFPРуководство по аппаратной части
-
Moxa EDS-G512E-8PoE-4GSFPИнструкция по эксплуатации
-
Moxa EDS-P510A-8PoE-2GTXSFP-T .Технические характеристики -
Moxa EDS-P510A-8PoE-2GTXSFP-T .Руководство по созданию резервированных сетей
Learn how to configure communication redundancy protocols like STP, RSTP, and MSTP for network stability. Manage root bridges, forwarding delay, and other settings to prevent loops and enhance reliability.