![Moxa IMC-101G-IEX [12/14] Auto mdi mdi x connection](/img/pdf.png)
Moxa IMC-101G-IEX [12/14] Auto mdi mdi x connection
![Moxa IMC-101G-T [12/14] Auto mdi mdi x connection](/views2/1197908/page12/bgc.png)
- 12 -
LED Indicators
The front panel of the IMC-101G has several LED indicators. The function
of each LED is described in the table below.
LED
Color
State
Description
PWR1
Amber
On
Power is being supplied to power input PWR1
Off
Power is not being supplied to power input
PWR1
PWR2
Amber
On
Power is being supplied to power input PWR2
Off
Power is not being supplied to power input
PWR2
FAULT
Red
On
When the corresponding PORT alarm is
enabled and the port’s link is inactive.
Off
When the corresponding PORT alarm is
enabled and the port’s link is active, or when
the corresponding PORT alarm is disabled.
G2 Green
On
SFP port’s 1000 Mbps link is active.
Blinking
Data is being transmitted at 1000 Mbps.
Off
SFP port’s 1000 Mbps link is inactive.
G1 Green
On
TP port’s 1000 Mbps link is active
Blinking
Data is being transmitted at 1000 Mbps
Off
TP port’s 1000 Mbps link is inactive
10M Green
On
TP port’s 10 Mbps link is active
Blinking
Data is being transmitted at 10 Mbps
Off
TP port’s 10 Mbps link is inactive
100M Green
On
TP port’s 100 Mbps link is active
Blinking
Data is being transmitted at 100 Mbps
Off
TP port’s 100 Mbps link is inactive
Auto MDI/MDI-X Connection
The Auto MDI/MDI-X function allows users to connect the IMC-101G’s
10/100/1000BaseT(X) ports to any kind of Ethernet device, without
paying attention to the type of Ethernet cable being used for the
connection. This means that you can use either a straight-through cable
or crossover cable to connect the IMC-101G to Ethernet devices.
Dual-Speed Functionality and Switching
The IMC-101G’s 10/100/1000 Mbps RJ45 switched port auto negotiates
with the connected device for the fastest data transmission rate
supported by both devices. All models of the IMC-101G are plug-and-play
devices, so that software configuration is not required at installation, or
during maintenance. The half-duplex or full-duplex mode for the RJ45
switched ports is user dependent and changes (by auto-negotiation) to
full-duplex or half-duplex, depending on which transmission speed is
supported by the attached device.
Auto-Negotiation and Speed Sensing
All of the IMC-101G’s RJ45 Ethernet ports independently support
auto-negotiation for transmission speeds of 10 Mbps, 100 Mbps , and
1000 Mbps, with operation according to the IEEE 802.3u standard.
This means that some nodes could be operating at 10 Mbps, while at the
same time, other nodes are operating at 100 Mbps or 1000 Mbps.
Содержание
- Edition 6 may 2016 1
- Imc 101g series quick installation guide 1
- Moxa industrial media converter 1
- Features 2
- Overview 2
- Package checklist 2
- Panel layouts of the imc 101g series 3
- Dimensions unit mm 4
- Din rail mounting 4
- Wall mounting optional 5
- Atex and iecex information 6
- Attention 6
- Warning warning 6
- Wiring requirements 6
- Attention 7
- Grounding the imc 101g 7
- Wiring the alarm contact 8
- Wiring the redundant power inputs 8
- 100 1000baset x ethernet port connection 9
- Attention 9
- Communication connections 9
- Basesfp fiber port 10
- Baset x ethernet port connection 10
- Redundant power inputs 10
- Alarm contact 11
- Attention 11
- Imc 101g dip switch setting 11
- Auto mdi mdi x connection 12
- Auto negotiation and speed sensing 12
- Dual speed functionality and switching 12
- Led indicators 12
- Alarm contact one relay output with current carrying capacity of 1 a 24 vdc resistive 13
- Auto negotiation takes place when an rj45 cable connection is made each time a link is enabled the imc 101g advertises its capability for using 10 mbps 100 mbps or 1000 mbps transmission speeds with the device at the other end of the cable expected to advertise similarly depending on what type of device is connected this will result in agreement to operate at a speed of 10 mbps 100 mbps or 1000 mbps 13
- Dip switches port break alarm mask link fault pass through sfp an force 13
- If an imc 101g s rj45 ethernet port is connected to a non negotiating device it will default to 10 mbps speed and half duplex mode as required by the ieee 802 u standard 13
- Interface rj45 ports 10 100 1000baset x auto negotiation speed f h duplex mode and auto mdi mdi x connection 13
- Led indicators pwr1 pwr2 fault 10 100m tp port 1000m tp and sfp port 13
- Optical fiber 1000basesx lsx lx lh lhx zx ezx 13
- Sfp ports 1000base sfp slot 13
- Specifications 13
- Supports sfp 1g series module only 13
- Technology standards ieee802 802 u 802 x 802 z ab link fault pass through 13
Похожие устройства
- Moxa IMC-101G-IEX Технические характеристики
- Moxa IMC-101G-T-IEX Инструкция по эксплуатации
- Moxa IMC-101G-T-IEX Руководство пользователя Англ.
- Moxa IMC-101G-T-IEX Технические характеристики
- MartinLogan Motion Vision X Руководство пользователя
- MartinLogan Motion 60XT Руководство пользователя
- MartinLogan Motion 50XT Руководство пользователя
- Moxa IMC-P101-M-SC Инструкция по эксплуатации
- Moxa IMC-P101-M-SC Технические характеристики
- Moxa IMC-P101-M-SC-T Инструкция по эксплуатации
- Moxa IMC-P101-M-SC-T Технические характеристики
- Moxa IMC-P101-M-ST Инструкция по эксплуатации
- Moxa IMC-P101-M-ST Технические характеристики
- Moxa IMC-P101-M-ST-T Инструкция по эксплуатации
- Moxa IMC-P101-M-ST-T Технический паспорт
- MartinLogan Motion 30 Руководство пользователя
- Moxa IMC-P101-S-SC Инструкция по эксплуатации
- Moxa IMC-P101-S-SC Технические характеристики
- Moxa IMC-P101-S-SC-T Инструкция по эксплуатации
- Moxa IMC-P101-S-SC-T Технические характеристики