Moxa V2416-LX [2/2] Attention
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Moxa V2416-LX [2/2] Attention

Moxa V2416-XPE [2/2] Attention
– 4 – – 5 – – 6 –
www.moxa.com/support
The Americas:
+1-714-528-6777 (toll-free: 1-888-669-2872)
Europe:
+49-89-3 70 03 99-0
Asia-Pacific:
+886-2-8919-1230
China:
+86-21-5258-9955 (toll-free: 800-820-5036)
2014 Moxa Inc., All Rights Reserved
10/100 Mbps
1000 MBps
1
--
TRD3+
2
--
TRD4+
3
--
TRD4-
4
ERx-
TRD1-
5
ETx+
TRD2+
6
ERx+
TRD1+
7
--
TRD3-
8
ETx-
TRD2-
Serial Ports
The serial ports use DB9 connectors. Each port can be configured
by software for RS-232, RS-422, or RS-485. The pin assignments
for the ports are shown in the following table:
Pin
RS-422
RS-485
(4-wire)
RS-485
(2-wire)
1
TxDA(-)
TxDA(-)
---
2
TxDB(+)
TxDB(+)
---
3
RxDB(+)
RxDB(+)
DataB(+)
4
RxDA(-)
RxDA(-)
DataA(-)
5
GND
GND
GND
6
---
---
---
7
---
---
---
8
---
---
---
Audio Interface
The V2416 comes with an audio input and an audio output,
allowing users to connect a speaker or an earphone.
DI/DO
The V2416 comes with a 6
-
ch digital input and
2
-ch digital output in the terminal block
connectors.
Hot-swappable and removable Storage Trays
The V2416 computers come with 2 removable slots for inserting
additional storage media; it also supports hot swapping for
convenient, fast, and easy storage expansion. The user-defined
programmable LEDs and the associated API for storage
management support storage plug/unplug functionality, automatic
storage removal, and storage status display. Refer to the
Hardware User's Manual for detailed storage installation.
Reset Button
Press the “Reset Button” on the rear panel of the V2416 to reboot
the system automatically. The Ready LED will blink on and off for
the first 5 seconds, and then maintain a steady glow once the
system has rebooted.
Real-time Clock
The V2416’s real-time clock is powered by a lithium battery. We
strongly recommend that you do not replace the lithium battery
without help from a qualified Moxa support engineer. If you need
to change the battery, contact the Moxa RMA service team.
ATTENTION
There is a risk of explosion
if the battery is replaced by one
of incorrect type.
Powering on the V2416
To power on the V2416, connect the power cable to the V2416’s
M12 power connector (located at the rear panel). Press the power
button to turn on the computer. Note that the Shielded Ground
wire should be connected to the central pin of the connector. It
takes about 30 seconds for the system to boot up. Once the system
is ready, the Power LED will light up.
Configuring the Ethernet Interface
Power on the V2416 computer after connecting a monitor,
keyboard, and mouse, and verifying that the power source is ready.
Once the operating system boots up, the first step is to configure
the Ethernet interface. The factory default settings for the V2416
LANs are show below. (Please note that the XPE and W7E models
use DHCP settings.)
Default IP Address
Netmask
LAN1
192.168.3.127
255.255.255.0
LAN2
192.168.4.127
255.255.255.0
Linux users should follow these steps:
If you are using the console cable for first-time configuration of the
network settings, enter the following commands to edit the
interfaces file:
#ifdown –a
//Disable LAN1/LAN2 interface first, before you
reconfigure the LAN settings. LAN 1 = eth0, LAN 2= eth1,
#vi /etc/network/interfaces
//check the LAN interface first//
After the boot settings of the LAN interface have been modified,
use the following command to activate the LAN settings
immediately:
#sync; ifup –a
XPE users should follow these steps:
1. Go to Start Network Connections.
2. Right-click Network Connections, click Properties. Next,
select Internet Protocol (TCP/IP), and then click
Properties.
3. Click OK after inputting the proper IP address and netmask.
W7E users should follow these steps:
1. Go to Start -> Control Panel-> Network and Internet ->
View network status and tasks -> Change adapter
setting.
2. In the screen of Local Area Connection Properties, click
Internet Protocol (TCP/IP) and then select Properties.
Select Internet Protocol Version 4, and then click
Properties.
3. Click OK after inputting the proper IP address and netmask.
NOTE: Refer to the User’s Manual for other configuration
information.

Содержание

Похожие устройства

Скачать