![Autel Autolink AL301 [6/109] Obd ii monitor readiness status](/img/pdf.png)
Autel Autolink AL301 [6/109] Obd ii monitor readiness status
5
1) EGR System
2) O2 Sensors
3) Catalyst
4) Evaporative System
5) O2 Sensor Heater
6) Secondary air
7) Heated Catalyst
8) A/C system
2.5 OBD II Monitor Readiness Status
OBD II systems must indicate whether or not the vehicle’s PCM’s
monitor system has completed testing on each component.
Components that have been tested will be reported as ―Ready‖, or
―Complete‖, meaning they have been tested by the OBD II system.
The purpose of recording readiness status is to allow inspectors to
determine if the vehicle’s OBD II system has tested all the
components and/or systems.
The power-train control module (PCM) sets a monitor to ―Ready‖ or
―Complete‖ after an appropriate drive cycle has been performed. The
drive cycle that enables a monitor and sets readiness codes to ―Ready‖
varies for each individual monitor. Once a monitor is set as ―Ready‖
or ―Complete‖, it will remain in this state. A number of factors,
including erasing of diagnostic trouble codes (DTCs) with a scan tool
or a disconnected battery, can result in Readiness Monitors being set
to ―Not Ready‖. Since the three continuous monitors are constantly
evaluating, they will be reported as ―Ready‖ all of the time. If testing
of a particular supported non-continuous monitor has not been
completed, the monitor status will be reported as ―Not Complete‖ or
―Not Ready.‖
In order for the OBD monitor system to become ready, the vehicle
should be driven under a variety of normal operating conditions.
These operating conditions may include a mix of highway driving and
stop and go, city type driving, and at least one overnight-off period.
Содержание
- Table of contents 1
- Safety precautions and warnings 2
- Diagnostic trouble codes dtcs 3
- General information 3
- On board diagnostics obd ii 3
- Dtc example 4
- Location of the data link connector dlc 4
- P 0 2 0 2 4
- Obd ii readiness monitors 5
- Obd ii monitor readiness status 6
- Obd ii definitions 7
- Specifications 9
- Tool description 9
- Using the scan tool 9
- Product features 10
- Vehicle coverage 10
- Operating instructions 12
- Reading codes 12
- Erasing codes 14
- Retrieving i m readiness status 16
- Rescanning data 18
- Viewing vin number 18
- Limited one year warranty 20
- Service procedures 20
- Warranty and service 20
- Caution parts or components should not be replaced based on only a dtc without first consulting the vehicle service manual for more information on possible causes of the fault as well as required testing procedures 21
- Definitions 21
- Diagnostic trouble code dtc 21
- Dtc definition 21
- Obdii generic dtc definitions 21
- The following diagnostic trouble code definitions lists provide only generic diagnostic trouble codes for manufacturer specific diagnostic trouble code definitions consult the vehicle s service manual or the enclosed cd software 21
Похожие устройства
- Autel MaxiCheck DPF Reset Руководство пользователя
- Autel AutoLink AL539B Руководство пользователя
- Autel MaxiTPMS TS401 Руководство пользователя
- Autel MaxiCheck PRO Руководство пользователя
- Autel MaxiCheck Oil Light/Service Reset Руководство пользователя
- Autel MaxiCheck EPB Руководство пользователя
- Autel Maxivideo MV201 8.5 мм Руководство пользователя
- Autel Maxivideo MV400 5.5 мм Руководство пользователя
- Autel Maxivideo MV400 8.5 мм Руководство пользователя
- Coolfort CF-1216 Инструкция по эксплуатации
- Coolfort СF-1221 Инструкция по эксплуатации
- Coolfort CF-0525GY Инструкция по эксплуатации
- Cremesso Compact Automatic Burgundy Red Инструкция по эксплуатации
- Cremesso LM 600 Инструкция по эксплуатации
- Cuckoo CMC-CHSS1004F Инструкция по эксплуатации
- Defender Optimum MS-125 Nano Инструкция по эксплуатации
- Defender Game Racer Turbo GT Инструкция по эксплуатации
- Delonghi VVX 1885 Stirella Инструкция по эксплуатации
- Delonghi CTI 2103.BZ Инструкция по эксплуатации
- Delonghi CTI 2103.CP Инструкция по эксплуатации