![Moxa ioLogik E2242-T — настройка модулей ввода и вывода для обмена данными [54/90]](/icons/site-icon-64.png){kind=icon}
Moxa ioLogik E2242-T — настройка модулей ввода и вывода для обмена данными [54/90]
Превью страниц
Страница 54 /
90
![Moxa ioLogik E2262 [54/90] Configuring output module](/views2/1201328/page54/bg36.png)
Click&Go V2 Click&Go V2 Developing Process
3-38
The ioLogik E2000 can simultaneously act as both an input module and an output module. Input module
operation would be configured in one rule, and another rule would be used to configure output module
operation.
NOTE
Only DI channels that are set to DI mode can mirror remote DO channels. Event Counter channels cannot be
used for peer
-to-peer I/O operation. For analog input and output channels, they must be configured to the
same voltage or current mode. Also, a digital channel can not mirror an analog output channel or vise
versa.
Configuring Output Module
The peer-to-peer I/O output module is configured using one Click&Go rule for each DO channel that is mirroring
a remote input channel. In the Click&Go tab, start a new rule, select Enable peer-to-peer I/O, and then
select Output channel. Specify the output channel that will mirror the remote input channel, the IP address
of the input module, and the input channel on the input module whose signals will be mirrored. The input
module must have specified the output module’s IP address as a destination IP.
When properly configured, the specified output channel will mirror the signals received by the specified remote
input channel, as if the channels were physically connected. For example, If the remote DI channel’s status
changes to “ON”, the specified DO channel’s status will change to “ON”. If the remote DI channel’s status
changes to “OFF”, the DO channel’s status will change to “OFF”.
Once both the input and output modules have been configured start peer-to-peer I/O operation by activating
the rule-set on both units and providing a valid network connection to each unit.
NOTE
Only DO channels that are set to DO mode can mirror remote DI channels. Pulse Output channels cannot be
used for peer
-to-peer I/O operation. For analog input and output channels, they must be configured to the
same voltage or current mode. Also, a digital channel can not mirror an analog output channel or vise versa.
Содержание
282- Click go v2 user s manual
- Edition 3 september 2016
- Www moxa com product
- Copyright notice
- Click go v2 user s manual
- Www moxa com support
- Trademarks
- Technical support contact information
- Disclaimer
- Table of contents
- Introduction
- Overview
- Click go v2 introduction
- Time stamped active messaging
- Rules for if then else style programming
- Remote control and control by remote
- Product and software support
- Peer to peer i o
- Local monitoring and local control
- Click go v2 introduction
- Click go v2 features
- Difference in programming method and space
- Difference in if conditions
- Click go v2 introduction
- Difference in then else actions
- Click go version check
- Click go v2 introduction
- Getting started
- Hardware connection
- System requirements
- Connecting to the network
- Click go v2 getting started
- Optional liquid crystal display module lcm
- Connecting the i o device
- Click go v2 getting started
- Attention
- Adding more i o channels
- Software preparation
- Ioadmin 3 x installation
- Click go v2 getting started
- Click go v2 getting started
- Attention
- Firmware update
- Click go v2 getting started
- Attention
- Reset to factory default
- Click go v2 getting started
- Click go v2 developing process
- I o configuration
- Configurable dio channel mode selection
- Click go v2 development process
- Click go v2 click go v2 developing process
- Attention
- Digital input mode selection
- Click go v2 click go v2 developing process
- Attention
- Digital output mode selection
- Click go v2 click go v2 developing process
- Click go v2 click go v2 developing process
- Analog input mode selection
- Click go v2 click go v2 developing process
- Analog output mode selection
- Temperature input mode selection
- Click go v2 click go v2 developing process
- Click go v2 click go v2 developing process
- Attention
- Alias name configuration
- Define global variables
- Click go v2 click go v2 developing process
- Testing the i o channels
- Timer settings
- Internal register settings
- Click go v2 click go v2 developing process
- Snmp trap server
- E mail server
- Click go v2 click go v2 developing process
- Click go v2 click go v2 developing process
- Active message server
- Work with logic
- Click go v2 click go v2 developing process
- Click go logic basics
- If a then b else c
- Click go v2 click go v2 developing process
- If conditions
- Click go v2 click go v2 developing process
- Click go v2 click go v2 developing process
- Counter
- Click go v2 click go v2 developing process
- Click go v2 click go v2 developing process
- Relay counter
- Click go v2 click go v2 developing process
- Internal register
- Click go v2 click go v2 developing process
- Remote action
- Click go v2 click go v2 developing process
- Schedule
- Click go v2 click go v2 developing process
- Host connection fail
- Click go v2 click go v2 developing process
- More info on repeat interval vs edge detection
- Click go v2 click go v2 developing process
- Click go v2 click go v2 developing process
- Then else actions
- Click go v2 click go v2 developing process
- Counter
- Click go v2 click go v2 developing process
- Pulse output
- Click go v2 click go v2 developing process
- Relay counts
- Click go v2 click go v2 developing process
- Internal register
- Click go v2 click go v2 developing process
- Remote action
- Click go v2 click go v2 developing process
- Click go v2 click go v2 developing process
- Attention
- Click go v2 click go v2 developing process
- Snmp trap
- Click go v2 click go v2 developing process
- Active message
- E mail
- Click go v2 click go v2 developing process
- Click go v2 click go v2 developing process
- Cgi command
- Peer to peer function
- Configuring input module
- Click go v2 click go v2 developing process
- Configuring output module
- Click go v2 click go v2 developing process
- Import export configuration
- Download restart and run
- Click go v2 click go v2 developing process
- Activating the rule set
- Rule set management bar
- Using ioadmin to import export configuration
- Export system configuration
- Click go v2 click go v2 developing process
- Using tftp to import export configuration
- Import system configuration
- Click go v2 click go v2 developing process
- Attention
- Click go examples and applications
- Where there is an on logic there should be an off logic
- Rules are running in a loop
- If then else
- If di_0 on then do_0 on else do_0 off
- If a then b else c
- Click go v2 click go examples and applications
- Click go rule 101
- Using the timer function
- Heartbeat or repeat actions
- Click go v2 click go examples and applications
- Attention
- On delay
- Click go v2 click go examples and applications
- Using internal registers
- Soft key
- Remote control
- Off delay
- Click go v2 click go examples and applications
- Programming examples
- Local i o control
- Click go v2 click go examples and applications
- Click go v2 click go examples and applications
- Active i o messages
- Peer to peer i o
- Click go v2 click go examples and applications
- Attention
- Input module iologik e2242 192 68 27 54
- Click go v2 click go examples and applications
- Output module 192 68 27
- Click go v2 click go examples and applications
- Solution benefits
- Project background
- Moxa solution
- Click go v2 click go examples and applications
- Applications_1
- Application requirements
- Additional features
- Click go rule set
- Click go programming example
- System diagram
- Programming manners
- I o alias and mode configuration
- Click go v2 click go examples and applications
- Solution benefits
- Project background
- Moxa solution
- Click go v2 click go examples and applications
- Applications_2
- Application requirements
- Additional features
- System diagram
- I o mode configuration
- I o alias configuration
- Click go v2 click go examples and applications
- Click go programming example
- Project background
- Programming manners
- Click go v2 click go examples and applications
- Click go rule set
- Applications_3
- Application requirements
- Solution benefits
- Moxa solution
- Click go v2 click go examples and applications
- Additional features
- System diagram
- I o alias and timer configuration
- Click go v2 click go examples and applications
- Click go programming example
- Applications_4
- Application requirements
- Project background
- Programming manners
- Click go v2 click go examples and applications
- Click go rule set
- System diagram
- Solution benefits
- Moxa solution
- Click go v2 click go examples and applications
- Additional features
- Programming manners
- I o mode configuration
- I o alias configuration
- Click go v2 click go examples and applications
- Click go programming example
- Applications_5
- Application requirements
- Project background
- Click go v2 click go examples and applications
- Click go rule set
- System diagram
- Solution benefits
- Moxa solution
- Click go v2 click go examples and applications
- Additional features
- Programming manners
- I o alias configuration
- Click go v2 click go examples and applications
- Click go rule set
- Click go programming example
- Applications_6
- Application requirements
- Additional features
- Solution benefits
- Project background
- Moxa solution
- Click go v2 click go examples and applications
- System diagram
- I o alias and mode configuration
- Click go v2 click go examples and applications
- Click go programming example
- Project background
- Programming manners
- Click go rule set
- Applications_7
- Application requirements
- Moxa solution
- Click go v2 click go examples and applications
- Additional features
- System diagram
- Solution benefits
- Programming manners of iologik e2210_site
- I o alias and timer configuration of iologik_site
- Click go v2 click go examples and applications
- Click go rule set of iologik e2210_site
- Click go programming example_site
- Click go v2 click go examples and applications
- Programming manners of iologik e2210_central
- I o alias and timer configuration of iologik_central
- Click go v2 click go examples and applications
- Click go rule set of iologik e2210_central
- Click go programming example_central
- Click go v2 click go examples and applications
- Internal registers modbus tcp
- A internal registers modbus tcp
- Xxxx read write registers functions 3 6 16
- Iologik e2210 e2212 and e2214
- Xxxx read write registers functions 3 6 16
- Iologik e2240 e2242 e2260 and e22262
- Click go v2 internal registers modbus tcp
Похожие устройства
-
Moxa ioPAC 5542-HSPA-IEC-TТехнические характеристики -
Moxa ioPAC 5542-HSPA-IEC-TРуководство по аппаратной части -
Moxa ioPAC 5542-HSPA-IEC-TИнструкция по эксплуатации -
Moxa ioPAC 5542-IEC-TТехнические характеристики
-
Moxa ioPAC 5542-IEC-TРуководство по аппаратной части
-
Moxa ioPAC 5542-IEC-TИнструкция по эксплуатации
-
Moxa ioPAC 5542-HSPA-C-TРуководство по аппаратной части
-
Moxa ioPAC 5542-HSPA-C-TТехнические характеристики
-
Moxa ioPAC 5542-HSPA-C-TИнструкция по эксплуатации
-
Moxa ioPAC 5542-C-TРуководство по аппаратной части
-
Moxa ioPAC 5542-C-TТехнические характеристики
-
Moxa ioPAC 5542-C-TИнструкция по эксплуатации
Узнайте, как правильно настроить модули ввода и вывода для обмена данными в режиме peer-to-peer. Подробные инструкции и советы по конфигурации.