M-Audio Biport 2x4s [25/48] Mac driver installation
![M-Audio Biport 2x4s [25/48] Mac driver installation](/views2/1020148/page25/bg19.png)
IMPORTANT: Only select the “Merge All” feature if your
MIDI application allows only one input to be selected at a
time in its MIDI setup. The “Merge All” can affect SMPTE
sync performance adversely because the MIDI Time Code
(MTC) from the SMPTE port must be merged with any other
MIDI data that is coming in on In-A or In-B. This incoming
MIDI data can “jitter” the MTC and make the timing look
irregular to the receiving MIDI application.
Mac Driver/OMS Installation
The BiPort OMS Driver is designed to run with Opcode’s “Open Music
System.” You will need the OMS application to use the BiPort 2x4s as a
multiport MIDI device. If you do not have Opcode’s OMS installed, or if
you are not using an application that supports OMS, you will not be able
to use the BiPort 2x4s. This is available as a free download from
Opcode’s website, and you will find a link to it on the drivers page of
the Midiman website.
To Install the BiPort on your Mac, first attach one side of the supplied
Mac serial cable (or any standard Mac serial cable) to the jack labeled
“Host In,” and the other side to either the printer or modem port on you
computer (for more information, consult the sections of the manual
titled “BiPort Installation” and “BiPort to Host Connection”).
Make sure that OMS has been successfully installed. After you are sure
that OMS is properly installed, go to the Control Panel or Chooser under
the Apple Menu, and make sure AppleTalk is turned off (this is recom-
mended, although OMS will sense that it is on and prompt you to turn it
off).
Mac Driver Installation
If you are installing your BiPort driver and configuring OMS for the first
time, follow these instructions to configure OMS. If you have a studio
setup already created in OMS and wish to create a new studio setup,
skip to the section below entitled “Installing with an existing Studio
Setup.”
25
Содержание
- Biport 2x 1
- Manual 1
- Table of contents 1
- Fcc class b and ce compliance 3
- Introduction 4
- Front and back panel 6
- Front panel 6
- Package contents 6
- Back panel 7
- Stand alone mode 7
- Theory of operation 7
- Midi interface mode 8
- Functions shared by both modes 9
- Smpte reader 9
- Smpte writer 9
- Smpte write button 10
- Mac thru button 11
- Smpte format button 11
- Biport 2x4s 12
- Midi hardware sequencer 12
- Typical stand alone setup fig 1 12
- Biport 2x4s installation 13
- Installation for midi interface mode 13
- Installation for stand alone mode 13
- Biport 2x4s 14
- Smpte in 14
- Typical midi interface system set up fig 2 14
- Biport to host connection 15
- Selecting a mac host serial port 16
- Selecting a pc host serial port 16
- About the serial cables 17
- Diagnostics software 17
- Pc diagnostics application 17
- Biport 2x4s 18
- Mac diagnostic application 19
- Internal buffers test 20
- Internal hardware test 20
- Test results for mac or pc 20
- Transmit receive test 20
- Pc drivers and driver installation 21
- Receive interrupt test 21
- Smpte i o test 21
- Windows 98 installation 22
- Windows 95 driver installation 23
- Driver configuration 24
- Mac driver installation 25
- Mac driver oms installation 25
- First time oms configuration instructions 26
- Installing with an existing studio setup 27
- Remote control software 27
- Remote control windows installation 27
- Remote control operation 28
- Smpte setup 28
- File load config 29
- Confirm exit 30
- Delete config 30
- Hardware current status 30
- Save config 30
- Help about 31
- Remote control mac installation 31
- Remote control operation 31
- Smpte test 31
- To set flywheel 32
- To set smpte frame rate 32
- To set smpte start time 32
- To set user bits 32
- File close 33
- File new setting 33
- File open setting 33
- File revert to saved 33
- File save settings or file save as 33
- File quit 34
- File save as default 34
- The edit menu 34
- The hardware menu 34
- The select menu 34
- Configuring applications to use biport 2x4s 35
- Smpte midi time code tutorial 36
- What is smpte time code 36
- About frame rates 37
- What is midi time code mtc 37
- Smpte and mtc user bits 38
- What frame rate and settings should you use 38
- Smpte offset 39
- Flywheeling 40
- Recording a smpte stripe writing smpte 40
- Syncing to smpte 40
- To record a smpte stripe onto tape follow these steps 41
- Syncing to a smpte stripe 43
- Interface trouble shooting 44
- Solution 1 44
- Trouble shooting 44
- Are your smpte audio cables good 46
- Syncing trouble shooting 46
- Before calling tech support 47
- Lifetime limited warranty 48
Похожие устройства
- JVC GR-DV400 Инструкция по эксплуатации
- Fujifilm FinePix AX380 Инструкция по эксплуатации
- HP Deskjet 2050 CH355C Инструкция по эксплуатации
- Polaris PRE S 0715 H Инструкция по эксплуатации
- JVC GR-DV3000 Инструкция по эксплуатации
- Stiebel Eltron DHB 12 SI 74036 Инструкция по эксплуатации
- Fujifilm FinePix JX360 Black Инструкция по эксплуатации
- HP Deskjet 3050 CH381C Инструкция по эксплуатации
- M-Audio Octane Инструкция по эксплуатации
- Polaris PRE S 0920 H Инструкция по эксплуатации
- JVC GR-DV3 Инструкция по эксплуатации
- Ariston Bravo E 7023 U-F 7 Инструкция по эксплуатации
- Fujifilm FinePix JV200 Инструкция по эксплуатации
- HP Photosmart WL eAiO B110b Инструкция по эксплуатации
- Panasonic aj-yax800g Инструкция по эксплуатации
- JVC GR-DV2000 Инструкция по эксплуатации
- Polaris PRE S 1125 H Инструкция по эксплуатации
- AEG MTD 570 222122 Инструкция по эксплуатации
- Fujifilm FinePix S3200 Инструкция по эксплуатации
- HP CN216C PSP eAiO B210b Инструкция по эксплуатации