Home
Главная
Timberk
Обогреватель
TEC.PS1 ML 15 IN (OG)
Инструкция по эксплуатации Страница: 4

Timberk TEC.PS1 ML 15 IN (OG) [4/16] Iiiiiiiiiiiiiiiiiii

Содержание

Instruction manual руководство по эксплуатации 1
Lllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllll 1
Timberk 1
Г модели models 1
Connection to electric mains 3
Control panel 2 outlet grill louver 3 unit s case front part 4 support legs 5 coldairinlet 6 humidifier 7 heated towel rail 3
Convector with a bracket and a carrying handle 1 pc 2 bracket s mounting screw 4 pcs 3 dowel 4 pcs 4 support leg 2 pcs 5 mounting screw of a support leg 8 pcs 6 remote controller only for tec ps1 rce in 1 pc 7 operation manual 1 pc 8 guarantee card 1 pc 9 packing 1 pc 3
Description of the convector fig 3 3
Distancefrom the floor 4 mark the height at which the convector is to be mounted then attach bracket to the wall 5 put visible marks in mounting holes 6 drill holes of the required diameter on the mounting holes insert dowels attach the mounting bracket and fasten adjusting screws thereby securing bracket on the wall fig 5 7 suspend the convector on the bracket for which purpose attach the lower part of the unit to the lower extension of the bracket and insert them into 3
English 3
For a detailed description of technical parameters and characteristics go to www timberk com orcontacttimberk official dealers 3
I the convector is designed to be connected to 220 230v single phase voltage mains with a grounding circuit 2 prior to connection make sure that parameters of electric mains in the place of connection comply with parameters indicated on the 3
Identification plate with technical data of the unit 3 it is necessary to follow active electrical safety precautions connecting the convectorto electric mains 3
Iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiihiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiih 3
Iniiiiiiiiiiiiiiii 3
Installation 3
Leg mounting of the convector fig 7 3
Mounting 5 turn over the unit to the right position and place it on a smooth horizontal surface strictly in a vertical position the unit is ready to use 3
Open the factory package and carefully remove the unitout of it 2 remove seals out of foamed plastic on sides of the unit and take it out of polyethylene 3 in accordance with fig 2 4 and table 2 determine the place of convector s installation observing minimum distances from objects and minimum 3
Optional devices not included in the stanc scope of delivery to be purchased separately 3
Overall dimensions of the convector as per fig are given intable 2 3
Scope of delivery 3
Slots available in the lower part of the unit s rear panel carrying out these actions it is necessary to hold the unit at the angle of 50 60 degrees fig 6 8 turn the unit in a horizontal plain until upper extensions of the bracket coincide with the upper slots in the unit s rear panel and slightly press on the unit until you hear clicking of the upper extensions fig 6 9 to dismount the unit press the leverages of the bracket s upper extensions and disconnect the unit from it then carry out the abovementioned operations in the reverse order 3
Table 1 3
Table 2 3
Take 2 legs out of a package box 2 turn over the unit so that its lower part was at the top 3 attach legs to the lower part of the unit from the left and right sides so that the mounting holes coincide with holes on the unit s case 4 fasten mounting screws in the present holes exerting enough force check security of 3
Technical characteristics 3
Technical characteristics of the convector are given in table 1 3
Wall mounting of the convector fig 4 5 6 dimensions are given in mm 3
Г series power tl mm h mm a mm l mm в mm h23 mm 3
Рис 4 3
Iiiiiiiiiiiiiiiiiii 4
Tec ps1 m in series control panel fig 8 4
Iiiiiiiiihiiiiiiiiiiiiiiiiiihiiihiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiihiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiim 5
Llllllllllllllllll 5
Ffkt utxteeimifiett mist нигишнпиш nigttifctuiмагякляш 14
Osiiiuisxiuimiiiiii iiiiiiiiiiitsiiliuiiii u043b ишлшииш п 14
Ешгпцшп 14
Тшншипяг 14
Чшхтт 14
Timberk 16
Данные могут быть изменены в связи со сменой производителя продавца производственного филиала и u0438ли импортера в рф и u0438ли страны етс актуальную информация вы можете получить из содержания действующего на момент продажи сертификата соответствия а также из данных этикетки которой маркируется упаковка изделия до даты последующей продажи дистрибьютором на территории рф или стран етс 16

Похожие устройства

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiimiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiim IIIIIIIIIIIIII lllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllll ENGLISH 4 An electric outlet must be properly grounded The outlet must be designed for rated current not less than 10A for models with maximum power up to 2000W and not less than 12A for models with maximum power of 2500W Electric outlet and plug must always stay dry to prevent current leakage Regularly check if the electric plug is tightly connected to the outlet It must be done in the following order connect an electric plug into an outlet after half hour operation turn off the convector and disconnect the plug from the outlet check if the plug is heated by your hand If the plug heated over 50 C then replace the outlet by a new one to prevent damages incidents fire as a result of bad electric contact A specialist must do the job O IMPORTANT The electric outlet must be rated for not less than 10A for models with maximum power up to 2000W and not less than 12A for models with maximum power of 2500W electric cable with a strand with cross section not less than 3x1 5 mm2 for copper 7 Control of the convector heater TEC PS1 M IN series control panel Fig 8 Fig 8 www timberk com electric convector heater modes low power 6 1 You can switch on and off the air ionizer by means of the ionizer switch Ionizer located on the control panel 6 2 Ionizer switch illumination lights up when the air ionizer is switched on 6 3 The air ionizer is a completely independent device and can operate even when the unit s heating mode is off li l lllllll lll llll l lllllllll lllll ll ll lllllllllllllllllll ll lll IW O NOTE A small static electric charge may be accumulated on metal surfaces of a case In units equipped with an air ionizer If your electric main has no grounding circuit or it is damaged In this Operation of TEC PS 1 M IN series convector heater TEC PS1 M IN series convector heaters are equipped with a mechanical thermostat TEC PS1 LE IN series convector heaters are equipped with a highprecision electronic thermostat with LED display TEC PS1 RCE IN series convector heaters are equipped with a highprecision electronic thermostat with LED display and a remote controller TEC PS1 PGE IN series convector heaters are equipped with a highprecision electronic thermostat LCD display and weekly programming of convector operation modes 6 1 Heating power mode selector It is used to select the following heating power Economy high power Normal 2 Power indicator It is illuminated when the unit is connected to electric mains 3 Ionizer switch Ionizer It is used to switch on off the air ionizing function 4 heating indicator light It is illuminated when the unit s heating is on 5 Thermostat handle It is used to setthe desired room temperature 1 Switch on the convector heater Connect the convector to electric mains by plugging the power cord into an electric outlet at that POWER indicator light will be illuminated on the control panel 2 Selectthe heating power With the help of the heating power mode selector setthe required heating power low power Economy high power Normal 3 Set temperature 3 1 Temperature can be set within the range 5 to 30 C 3 2 Turn the thermostat handle clockwise to the stop at that if room temperature is below the set one then the heating indicator must be illuminated When the room temperature reaches the desired level turn the thermostat handle counterclockwise until the unit is switched off the heating indicator light will go out Now the thermostat will maintain the set temperature switching on and off the convector from time to time During especially cold weather the convector may not be able to provide the required room heating In this case set the thermostat to the level somewhat higherthan the desired one 4 Antifreeze mode Turn the thermostat handle counterclockwise to position L The thermostat will automatically switch on heating of the convector if the room temperature goes below 5 C and the unit is connected to electric mains and the heating mode is on 5 Comfort mode Comfort mode which can be selected by means of the thermostat handle corresponds to the most comfortable room temperature 6 Air ionizing function The convector is equipped with an air ionizer IIIIMIIIIIIIIUIIIIIIIIIIIIIIIIIIIilllllllllllllllllllllllllllillllllUIIIIllIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIN O IMPORTANT If the unit is operated without a grounding circuit or it is damaged it is not recommended to switch on and operate the air ionizer TEC PS1 LE IN and TEC PS1 RCE IN series control panel Fig 9 5 Ionizer air ionizer indicator It is illuminated when the air ionizing function is activated 6 Ionizer button a It is used to turn on off air ionizing 7 Button B It is used to select the following operation modes low power LO symbol high power HI symbol 8 Economy mode indicator It is illuminated when the convector is operating in the economy mode 9 Button O It is used to increase the selected value 10 Button O It is used to decrease the selected value 11 Timer indicator Timer It is illuminated when the convector switch off timer function is activated 12 Button B It is used to select the economy mode Economy indicator comfort mode Normal indicator antifreeze mode AF symbol as well as to set the timer 13 Power switch It is used to switch on off the convector heater TEC PS1 RCE IN series remote controller Fig 10 It is used to switch on and off the convector heater 2 Power indicator It is illuminated at turning on the power switch when the unit is connected to electric mains 3 Normal comfort mode indicator It is illuminated when the convector heater is operating in the comfort mode 4 LED display LED display can show temperature settings heating power modes and timer settings 1 LCD display It displays temperature timer settings as well as unit s operation symbols and operation symbols 2 Button A It is used to increase the selected value 3 Button MODE It is used to select the following heating power modes low power symbol high power w symbol 4 Button It is used to decrease the selected value 5 Button POWER It is used to switch on off the convector heater 6 Button SET It is used to select the economy mode symbol comfort mode symbol antifreeze mode symbol and to set the timer 7 Button ION It is used to switch on off the air ionizing function Fig 10 www timberk com electric convector heater 7

Скачать