Home
Главная
Aten
VM5404D
Руководство пользователя Страница: 91

Aten VM5404D [91/118] Serial control protocol commands

Chapter 5

RS-232 Commands

Serial Control Protocol Commands

The VM5404D / VM5808D’s built-in bi-directional RS-232 serial interface

allows system control through a high-end controller or PC. The RS-232

commands for the VM5404D and VM5808D are the same, with the only

difference being that the VM5808D has 4 additional ports.

RS232 Pin Assignment

Configuring the Serial Port

The controller’s serial port should be configured as follows:

Pin Description Pin Description

1 Not connected 6 Not connected

2 RXD 7 Not connected

3 TXD 8 Not connected

4 Not connected 9 Not connected

5GND

Baud Rate 19200

Data Bits 8

Parity None

Stop Bits 1

Flow Control None

Содержание

Vm5404d vm5808d user manual p.1
Emc information p.2
This product has been classified as information technology equipment p.3
The following contains information that relates to china p.3
Sj t 11364 2006 p.3
Safety p.3
User information p.4
Telephone support p.4
Online registration p.4
User notice p.4
Package contents p.5
Introduction p.6
Hardware setup p.6
Front panel configuration p.6
Contents p.6
Chapter 3 p.6
Chapter 2 p.6
Chapter 1 p.6
Chapter 4 p.7
Browser operation p.7
Rs 232 commands p.9
Chapter 5 p.9
Appendix p.9
About this manual p.10
Conventions p.11
This manual uses the following conventions p.11
Product information p.11
For information about all aten products and how they can help you connect without limits visit aten on the web or contact an aten authorized reseller visit aten on the web for a list of locations and telephone numbers p.11
This page intentionally left blank p.12
Overview p.13
Introduction p.13
Chapter 1 p.13
Features p.14
Source devices p.15
Requirements p.15
Display devices p.15
Cables p.15
Supported web browsers are shown in the table below p.16
Supported operating systems are shown in the table below p.16
Source device operating systems p.16
Browsers p.16
Vm5404d front view p.17
Components p.17
Vm5404d rear view p.18
Vm5808d front view p.19
Vm5808d rear view p.20
The vm5404d s ir remote control only supports use of the 1 4 input p.21
Ir remote control p.21
And 1 4 output pushbuttons p.21
This page intentionally left blank p.22
Rack mounting p.23
Hardware setup p.23
Chapter 2 p.23
Grounding p.24
Cable connection p.25
Vm5404d vm5808d user manual p.26
Installation diagram p.26
Overview p.27
Front panel pushbuttons p.27
Front panel configuration p.27
Chapter 3 p.27
Enter password p.28
Port switching p.29
Main screen p.29
Input port selection p.29
Output port selection p.31
Vm5808d p.33
The vm5404d vm5808d has a built in configuration utility via the front panel lcd which can be controlled by pressing the menu and front panel input pushbuttons 1 8 user can cycle through the menu options starting from ip setting page in the order shown in the table below p.33
Note the highlighted values are the default settings of the vm5404d p.33
Lcd menu organization p.33
Chapter 3 front panel configuration p.33
Ip setting p.34
Ip address subnet mask p.34
Menu pushbutton p.34
Gateway p.35
Serial port setting p.36
Baud rate p.36
Operation mode p.37
Edid mode p.37
Output status p.39
Security mode p.41
Change password p.42
Save to a profile p.43
Play stop the profile schedule p.44
Profile pushbutton p.45
Power on off individual output displays p.46
Ir remote control operation p.46
Change the input source of an output display p.46
Power on off all output displays p.47
This page intentionally left blank p.48
Overview p.49
Logging in p.49
Chapter 4 p.49
Browser operation p.49
Menu bar p.50
Main page p.50
Profile list p.51
Adding playing a profile p.51
Importing exporting a profile p.53
Profile list options p.54
Profile p.54
Play window p.54
Clicking a profile or the play window opens a pop up menu with options p.54
Profile scheduling is located below the profile list scheduling allows you to queue and play connection profiles in sequence for a specific amount of time p.56
Profile scheduling p.56
After selecting edit you will be presented with the following options p.57
Digital signage profile p.58
Connection profiles p.58
Select source p.59
Output icon p.59
Grid view p.60
Click cancel to undo all unsaved changes output options p.60
Video wall profile p.61
Video wall options p.61
Number of displays output order bezel dimensions p.62
Null input p.63
Independent output p.64
Grouping p.64
Display preferences p.65
Video wall example p.66
Dvi video options p.67
Output options p.67
System settings p.69
General p.70
Fan status p.70
Device info p.70
User account p.72
Add account p.73
Permission level p.74
Port name p.75
Network p.76
Edid mode p.78
Customized mode p.79
Edid cea description p.80
Customized edid settings p.81
Firmware p.84
Configuration menu p.87
Telnet operation p.87
H call up the command list for help p.87
Ri read what input is connected to nn output p.88
Pw change password p.88
Lo load connections from profile p.88
Ip set ip address p.88
Im set ip subnet mask p.88
Gt set gateway address p.88
Vr software version information p.89
Ti set timeout p.89
Sv save the current connections into a profile p.89
Ss switch input to specified output p.89
Sb set serial port baud rate p.89
Ro read what output is connected to nn input p.89
This page intentionally left blank p.90
Chapter 5 p.91
Serial control protocol commands p.91
Rs232 pin assignment p.91
Rs 232 commands p.91
Configuring the serial port p.91
Verification p.92
To turn off video output on port 03 type p.93
To switch output port 04 to the next port type p.93
The switch port command allows you to switch ports on the vm5404d vm5808d p.93
The formula for the switch command is as follows p.93
The following tables show the possible values for the switch port command p.93
Switch port command p.93
Sw o04 enter p.93
Sw o03 off enter p.93
Sw i02 o05 enter p.93
For example to switch input port 02 to output port 05 type p.93
Command input number output number control enter p.93
Vm5404d vm5808d user manual p.94
The port number can be skipped and the default value will be used p.94
The following table lists the available switch port commands p.94
Note 1 by default input port 01 is tied to output port 01 input port 02 is tied to output port 02 and so on until port 08 i e o01 i01 o02 i02 p.94
Each command string can be separated with a space p.94
The formula for the edid command is as follows p.95
The following tables show the possible values for the edid command p.95
The following table lists the available edid commands p.95
Note each command string can be separated with a space p.95
For example to use the port1 edid mode type p.95
Extended display identification data edid is a data that contains a display s basic information and is used to communicate with the video source p.95
Edid port1 enter p.95
Edid mode command p.95
Command control enter p.95
For example to mute the audio coming from output port 1 type p.97
Command output number control enter p.97
The formula for the mute command is as follows p.97
The following tables show the possible values for the mute command p.97
The following table lists the available mute commands p.97
Skip the output port command to mute or enable the audio of all p.97
Output ports p.97
Note 1 each command string can be separated with a space p.97
Mute o01 on enter p.97
Mute command p.97
Mute allows you to enable or disable an output port s audio p.97
The following tables show the possible values for the scaling command p.98
Scaling o04 1080p enter p.98
Scaling o02 off enter p.98
Scaling o native enter p.98
Scaling command p.98
For example to turn scaling off for output port 02 type p.98
Command output number 1 horizontal resolution number 2 vertical resolution number 3 frequency number 4 control enter p.98
To set the scaling for output port 04 to 1920x1080 60hz type p.98
To set the scaling for all output ports to the connected display s native resolution type p.98
The scaling command allows you to set a resolution for scaling the display connected to an output port p.98
The formula for the scaling command is as follows p.98
Value will be used p.99
The port number command string can be skipped and the default p.99
The following table lists the available scaling commands p.99
Note 1 each command string can be separated with a space p.99
The following table lists the available fan speed commands p.102
The fan speed command allows you to set the vm5808d s internal fan speed p.102
Note this feature is not supported by the vm5404d p.102
Note each command string can be separated with a space p.102
For example to set the fan to low speed type p.102
Fan speed command p.102
Fan low enter p.102
Command control enter p.102
To set the fan speed use the following command p.102
The following tables show the possible values for the fan speed command p.102
The formula for the echo command is as follows p.103
The following tables show the possible values for the echo comman p.103
The following table lists the available echo commands p.103
The echo function updates the rs232 controller when operations are made via the front panel pushbuttons web browser or telnet the changes echo back to the rs232 controller to keep the settings in sync with the device p.103
Note each command string can be separated with a space p.103
For example to enable the echo feature type p.103
Echo on enter p.103
Echo command p.103
Command control enter p.103
Note each command string can be separated with a space p.104
For example to enable the black screen function type p.104
Command control enter p.104
Blackscreen on enter p.104
Black screen command p.104
The formula for the black screen command is as follows p.104
The following tables show the possible values for the black screen comman p.104
The following table lists the available black screen commands p.104
The black screen command turns a display screen black when no source signal is detected this prevents the display from showing the default blue or other color used when no source signal is detected p.104
Read command p.105
The reset command allows you to reset the vm5404d vm5808d to the default factory settings p.106
The formula for the reset command is as follows p.106
The following tables show the possible values for the reset command p.106
The following table lists the available reset commands p.106
Reset command p.106
Note each command string can be separated with a space p.106
Command enter p.106
For example to set 38400 as the baud rate type p.107
Command control enter p.107
Baud rate command p.107
Baud 38400 enter p.107
The formula for the baud rate command is as follows p.107
The following tables show the possible values for the baud rate command p.107
The following table lists the available baud rate commands p.107
The baud rate command allows you to set the rs 232 data rate for the vm5404d vm5808d to use options are 9600 19200 default 38400 and 115200 p.107
Note each command string can be separated with a space p.107
The save load profile command allows you to save and load connection profiles saving profiles will save the connections currently in use p.108
The formula for the save load profile command is as follows p.108
The following tables show the possible values for the save load profile commands p.108
The following table lists the available save load profile commands p.108
Save load profile command p.108
Profile f 02 save enter p.108
Note each command string can be separated with a space p.108
For example to save the current connection configuration to profile 02 type p.108
Command profile number control enter p.108
For example to disable the osd for all outputs type p.109
Command output number control enter p.109
To enable or disable the on screen display osd for displays use the following command p.109
The following tables show the possible values for the osd command p.109
The following table lists the available osd commands p.109
Osd o07 on enter p.109
Osd o off enter p.109
Osd command p.109
Note each command string can be separated with a space p.109
For example to enable the osd for output 07 type p.109
To trigger a warning when issues arise for a specific input port use the following command p.110
The following tables show the possible values for the alert command p.110
Note each command string can be separated with a space p.110
For example to enable the basic alert function for input port 1 type p.110
Command input number control enter p.110
Alert i01 m1 enter p.110
Alert command p.110
The following table lists the available alert commands p.111
This page intentionally left blank p.112
Safety instructions p.113
General p.113
Appendix p.113
Rack mounting p.115
Technical support p.116
North america p.116
International p.116
Specifications p.117
The direct vendor also reserves the right to revise or update the device or documentation without obligation to notify any individual or entity of such revisions or update for further inquiries please contact your direct vendor p.118
Limited warranty p.118

Aten VM5404D [91/118] Serial control protocol commands

Содержание

Похожие устройства