![ECS Elitegroup K8T890-A [31/93] Installing the motherboard](/img/pdf.png)
ECS Elitegroup K8T890-A [31/93] Installing the motherboard
![ECS Elitegroup K8T890-A [31/93] Installing the motherboard](/views2/1212435/page31/bg1f.png)
25
Installing the Motherboard
USB2~3: Front Panel USB headers
The motherboard has four USB ports installed on the rear edge I/O port array. Additionally,
some computer cases have USB ports at the front of the case. If you have this kind of case,
use auxiliary USB connector to connect the front-mounted ports to the motherboard.
Please make sure that the USB cable has the same pin assignment as indi-
cated above. A different pin assignment may cause damage or system hang-
up.
1 USBPWR Front Panel USB Power
2 USBPWR Front Panel USB Power
3 USB_FP_P0- USB Port 0 Negative Signal
4 USB_FP_P1- USB Port 1 Negative Signal
5 USB_FP_P0+ USB Port 0 Positive Signal
6 USB_FP_P1+ USB Port 1 Positive Signal
7 GND Ground
8 GND Ground
9 Key No pin
10 USB_FP_OC0 Overcurrent signal
Pin Signal Name Function
SATA1~2: Serial ATA connectors
These connectors are use to support the new Serial ATA devices for the highest date transfer
rates (150 MB/s), simpler disk drive cabling and easier PC assembly. It eliminates limitations
of the current Parallel ATA interface. But maintains register compatibility and software
compatibility with Parallel ATA.
Pin Signal Name Function
1 Ground 2 TX+
3 TX- 4 Ground
5 RX- 6 RX+
7 Ground - -
Pin Signal Name
Pin Signal Name
SIR1: Infrared header
The mainboard supports an Infrared (SIR1) data port. Infrared port allows the wireless
exchange of information between your computer and similarly equipped devices such as
printers, laptops, Personal Digital Assistants (PDAs), cell phones, and other computers.
Pin Signal Name Function
1 Not Assigned Not assigned
2 Key No pin
3 +5V IR Power
4 GND Ground
5 IRTX IrDA serial output
6 IRTX IrDA serial input
Содержание
- Copyright 3
- Disclaimer 3
- Federal communications commission fcc 3
- Preface 3
- Trademark recognition 3
- About the manual 4
- Canadian department of communications 4
- Declaration of conformity 4
- Preface 4
- Chapter 1 1 5
- Chapter 2 7 7 7 7 7 5
- Chapter 3 27 27 27 27 27 5
- Preface i 5
- Tttttable of contents able of contents able of contents able of contents able of contents 5
- Chapter 1 introducing the motherboard 7
- Introducing the motherboard 7
- Introduction 7
- Audio codec 8
- Chipset 8
- Feature 8
- Introducing the motherboard 8
- Memory 8
- Processor 8
- Bios firmware 9
- Expansion options 9
- Integrated i o 9
- Introducing the motherboard 9
- Onboard lan optional 9
- Introducing the motherboard 11
- Table of motherboard components 11
- Chapter 2 installing the motherboard 13
- Choosing a computer case 13
- Installing the motherboard 13
- Installing the motherboard in a case 13
- Safety precautions 13
- Checking jumper settings 14
- Installing the motherboard 14
- Setting jumpers 14
- Checking jumper settings 15
- Installing the motherboard 15
- Jumper settings 15
- Connecting 20 24 pin power cable 16
- Connecting case components 16
- Installing the motherboard 16
- Cpu_fan1 sys_fan1 nb_fan fan power connectors 17
- Installing the motherboard 17
- Power 12v 3 17
- Pwr1 atx 24 pin power connector 17
- Pwr2 atx 12v power connector 17
- Sensor 17
- Spk1 internal speaker 17
- System ground 17
- Connecting pins 1 and 3 to a front panel mounted led provides visual indication that data is being read from or written to the hard drive for the led to function properly an ide drive should be connected to the onboard ide interface the led will also show activity for devices connected to the scsi hard drive activity led connector 18
- Connecting pins 2 and 4 to a single or dual color front panel mounted led provides power on off sleep and message waiting indication 18
- Front panel header 18
- Hard drive activity led 18
- Installing the motherboard 18
- Power sleep message waiting led 18
- Power switch 18
- Reset switch 18
- Supporting the power on off function requires connecting pins 6 and 8 to a momentary contact switch that is normally open the switch should maintain contact for at least 50 ms to signal the power supply to switch on or off the time requirement is due to internal de bounce circuitry after receiving a power on off signal at least two seconds elapses before the power supply recognizes another on off signal 18
- Supporting the reset function requires connecting pin 5 and 7 to a momentary contact switch that is normally open when the switch is closed the board resets and runs post 18
- The front panel connector panel1 provides a standard set of switch and led header commonly found on atx or micro atx cases refer to the table below for information 18
- Before installing the processor 19
- Installing hardware 19
- Installing the motherboard 19
- Installing the processor 19
- Cpu installation procedure 20
- Ddr sdram memory module table 20
- Installing memory modules 20
- Installing the motherboard 20
- Installation procedure 21
- Installing the motherboard 21
- Installing the motherboard 22
- Size vendor model name 22
- Chip selects data bus 23
- Installing the motherboard 23
- Maximum dram speed 23
- Note for memory types must be set to values consistent with system hardware 23
- Table b unbuffered dimm support for 939 pin 23
- About ide devices 24
- About ultradma 24
- Installing a hard disk drive cd rom sata hard drive 24
- Installing the motherboard 24
- About sata connectors 25
- Installing serial ata hard drives 25
- Installing the motherboard 25
- Fdd1 floppy disk connector 26
- Installing a floppy diskette drive 26
- Installing the motherboard 26
- Installing add on cards 27
- Installing the motherboard 27
- Installing the motherboard 28
- Installing the motherboard 29
- Nvidia 29
- Table a agp express graphics cards support list 29
- Vga chip model name agp 29
- Audio2 front panel audio header 30
- Cd in left channel 2 30
- Cd in right channel 30
- Cd1 cd audio input header 30
- Connecting optional devices 30
- Ground 3 30
- Ground 4 30
- Installing the motherboard 30
- Refer to the following for information on connecting the motherboard s optional devices 30
- This header allows the user to install auxiliary front oriented microphone and line out ports for easier access 30
- Installing the motherboard 31
- Overcurrent signal 31
- Please make sure that the usb cable has the same pin assignment as indi cated above a different pin assignment may cause damage or system hang up 31
- Sata1 2 serial ata connectors 31
- Sir1 infrared header 31
- The mainboard supports an infrared sir1 data port infrared port allows the wireless exchange of information between your computer and similarly equipped devices such as printers laptops personal digital assistants pdas cell phones and other computers 31
- The motherboard has four usb ports installed on the rear edge i o port array additionally some computer cases have usb ports at the front of the case if you have this kind of case use auxiliary usb connector to connect the front mounted ports to the motherboard 31
- These connectors are use to support the new serial ata devices for the highest date transfer rates 150 mb s simpler disk drive cabling and easier pc assembly it eliminates limitations of the current parallel ata interface but maintains register compatibility and software compatibility with parallel ata 31
- Usb2 3 front panel usb headers 31
- Connecting i o devices 32
- Installing the motherboard 32
- About the setup utility 33
- Chapter 3 using bios 33
- Entering the setup utility 33
- The standard configuration 33
- Using bios 33
- Bios navigation keys 34
- Esc exits the current menu 34
- F1 displays a screen that describes all key functions 34
- F10 saves the current configuration and exits setup 34
- F9 loads the optimized default setting for better performance 34
- Key function 34
- Press del f1 to enter setup press the delete key or f1 to access the bios setup utility 34
- Pu pd modifies the selected field s values 34
- Scrolls through the items on a menu 34
- The bios navigation keys are listed below 34
- Using bios 34
- Updating the bios 35
- Using bios 35
- Date and time 36
- Primary secondary third ide master slave 36
- Standard cmos setup 36
- The date and time items show the current date and time on the computer if you are running a windows os these items are automatically updated whenever you make changes to the windows date and time properties utility 36
- This option displays basic information about your system 36
- Using bios 36
- Your computer has one ide channel and each channel can be installed with one or two devices master and slave in addition this motherboard supports four sata channels and each channel allows one sata device to be installed use these items to configure each device on the ide channel 36
- Advanced setup 37
- Bit data transfer enabled 37
- Block multi sector transfer auto enable this item to enhance hard disk performance by reading or writing more data during each transfer this default setting is auto 37
- Floppy a b 37
- If you enable this item the system starts up more quickly because of the elimination of some of the power on test rutines 37
- Mb under dos and windows for netware and unix users select disabled to disable the lba large mode 37
- Pio dma mode auto this item enables users to select pio dma mode 37
- Quick boot enabled 37
- S m a r t auto the s m a r t self monitoring analysis and reporting technology system is a diag nostics technology that monitors and predicts device performance s m a r t software resides on both the disk drive and the host computer 37
- These items set up size and capacity of the floppy diskette drive s installed in the system 37
- This page sets up more advanced information about your system handle this page with caution any changes can affect the operation of your computer 37
- To return to the ide configuration page 37
- To return to the main menu setting page 37
- Type auto this item enables users to select the type of device connected to the system 37
- Using bios 37
- Using bios 38
- Ecp mode dma channel dma3 39
- Features setup 39
- Onboard floppy controller enabled 39
- Onboard ir port disabled 39
- Onboard pci ide controller both 39
- Parallel port address 378 39
- Parallel port irq irq7 39
- Parallel port mode ecp 39
- Serial port1 address 3f8 irq4 39
- This page sets up some parameters for peripheral devices connected to the system 39
- Use this item to assign irq to the parallel port 39
- Use this item to assign the dma channel under ecp mode function 39
- Use this item to enable or disable either or both of the onboard primary and secondary ide channels 39
- Use this item to enable or disable the onboard com1 serial port and to assign a port address 39
- Use this item to enable or disable the onboard floppy disk drive interface 39
- Use this item to enable or disable the onboard ir port function 39
- Use this item to enable or disable the onboard parallel port and to assign a port address 39
- Use this item to select the parallel port mode you can select normal standard parallel port ecp extended capabilities port epp enhanced parallel port or epp ecp 39
- Using bios 39
- Acpi aware o s yes this itme supports acpi advanced configuraion and power management interface use this item to enable or disable the acpi feature 40
- Audio device enabled 40
- Enable this item if you plan to use the usb ports on this motherboard 40
- Enable this item if you plan to use the usb ports on this motherboard in a dos environ ment 40
- Ethernet device enabled 40
- Modem device enabled 40
- Onboard sata ide raid 40
- Onboard usb function enabled 40
- Power management enabled use this item to enable or disable a power management scheme if you enable power management you can use this item below to set the power management operation both apm and acpi are supported 40
- Power mangement setup 40
- This page sets up some parameters for system power management operation 40
- To return to the main menu setting page 40
- Usb function for dos disabled 40
- Use this item to enable or disable the onboard ethernet 40
- Use this item to enable or disalbe the onboard audio device 40
- Use this item to enable or disalbe the onboard modem device 40
- Use this item to set the sata ide function mode 40
- Using bios 40
- Using bios 41
- If this item is enabled an irq will be assigned to the pci vga graphics system you set this value to no to free up an irq 42
- Pci ide busmaster disabled 42
- Pci plug and play setup 42
- Primary graphics adapter pci e vga 42
- This item enables or disabled the dma under dos mode we recommend you to leave this item at the default value 42
- This itme indicates if the primary graphics adapter uses the pci e vga pci vga or agp express allocate irq to pci vga yes 42
- This page sets up some parameters for devices installed on the pci bus and those utilizing the system plug and play capability 42
- To return to the main menu setting page 42
- Using bios 42
- Bios security features 43
- Change supervisor password press enter 43
- Supervisor password not installed 43
- This item indicates whether a supervisor password has been set if the password has benn installed installed displays if not not installed displays 43
- This page helps you install or change a password 43
- To access the sub menu you can use the sub menu to change the supervisor password 43
- To return to the main menu setting page 43
- Using bios 43
- Cpu pnp setup 44
- Using bios 44
- Hardware monitor 45
- System hardware monitor 45
- These items display the monitoring of the overall onboard hardware health events such as cpu voltage dram voltage cpu temperature system temperature cpu fan and system fan etc 45
- This page helps you set up some parameters for the hardware monitoring function of this motherboard 45
- To return to the main menu setting page 45
- Using bios 45
- Discard changes and exit 46
- Load optimal defaults 46
- Save changes and exit 46
- Using bios 46
- About the software cd rom 47
- Auto installing under windows 98 me 2000 xp 47
- Chapter 4 using the motherboard software 47
- Using the motherboard software 47
- Running setup 48
- Using the motherboard software 48
- Drivers and software are automatically installed in sequence follow the onscreen instruc tions confirm commands and allow the computer to restart a few times to complete the installation 49
- Using the motherboard software 49
- Ami award flash memory utility 50
- Manual installation 50
- Using the motherboard software 50
- Utility software reference 50
- Winflash utility 50
- Chapter 5 via vt8237 sata raid setup guide 51
- Install the serial ata sata hard disks 51
- Via raid configurations 51
- Via vt8237 sata raid setup guide 51
- Enter confirm the selection 52
- Entering via tech raid bios utility 52
- Esc exit 52
- F1 view array 52
- Move to the next item 52
- The raid bios information on the setup screen shown is for reference only what you see on your screen may not by exactly the same as shown 52
- Via vt8237 sata raid setup guide 52
- Create array 53
- Raid 0 for performance 53
- Via vt8237 sata raid setup guide 53
- Raid 1 for data protection 54
- Via vt8237 sata raid setup guide 54
- Delete array 55
- Select boot array 55
- Serial number view 55
- Via vt8237 sata raid setup guide 55
- Duplicate critical raid 1 array 56
- Rebuild broken raid 1 array 56
- Via vt8237 sata raid setup guide 56
- Via vt8237 sata raid setup guide 57
- Confirming windows xp driver installation 58
- Existing windows xp driver installation 58
- Install driver in windows os 58
- Installing raid software drivers 58
- New windows os 2000 xp nt4 installation 58
- Via vt8237 sata raid setup guide 58
- Installation of via sata raid utility 59
- Via vt8237 sata raid setup guide 59
- Using via raid tool 60
- Via vt8237 sata raid setup guide 60
- Via vt8237 sata raid setup guide 61
- Via vt8237 sata raid setup guide 62
- Via vt8237 sata raid setup guide 63
- Caractéristiques 64
- Chipset 64
- Codec audio 64
- Français 64
- Multi language translation 64
- Mémoire 64
- Processeur 64
- E s intégrées 65
- Français 65
- Lan sur carte optionnel 65
- Microprogramme bios 65
- Multi language translation 65
- Options d extension 65
- Arbeitsspeicher 66
- Audio codec 66
- Chipsatz 66
- Deutsch 66
- Feature 66
- Multi language translation 66
- Prozessor 66
- Bios firmware 67
- Deutsch 67
- Erweiterungsmöglichkeiten 67
- Integrierte i o 67
- Multi language translation 67
- Onboard lan optional 67
- Audio codec 68
- Caratteristiche 68
- Chipset 68
- Italiano 68
- Memoria 68
- Multi language translation 68
- Processore 68
- Firmware bios 69
- I o integrato 69
- Italiano 69
- Lan su scheda opzionale 69
- Multi language translation 69
- Opzioni d espansione 69
- Características 70
- Chipset 70
- Codec de audio 70
- Español 70
- Memoria 70
- Multi language translation 70
- Procesador 70
- Bios firmware 71
- Español 71
- I o integrado 71
- Lan abordo optativo 71
- Multi language translation 71
- Opciones de expansión 71
- Características 72
- Codec áudio 72
- Conjunto de chips 72
- Memória 72
- Multi language translation 72
- Português 72
- Processador 72
- I o integrado 73
- Microprogramação bios 73
- Multi language translation 73
- Onboard lan opcional 73
- Opções de expansão 73
- Português 73
- 800 600 400 200 mhz のクロック率でのダブルデータ 74
- Ac 97 v2 仕様に準拠 74
- Audio codec 74
- Direct sound 3 74
- Dvdオーディオ信号再生のダブルサンプリングレート 96khz をサポート 74
- Hypertransport技術とは 二つのデバイスを1対1 point to point で接続する技術 であり 従来のインターコネクト技術に比較して 集積回路同士の情報交換を高速化しま す 74
- Hypertransport技術を導入したamd k8プロセッサに対応します 74
- K8t890 74
- K8t890 a には 次の特徴を持つ939ピンソケットが搭載されています 74
- Multi language translation 74
- Via k8t890 northbridge nb とvia vt8237 southbridge sb チップセットは 実 証された信頼性と性能を持つ革新的で拡張性のあるアーキテクチャに基づいています 74
- Vt8237 74
- に対応 74
- チップセット 74
- デュアルチャネル構成のddr400 333 266メモリタイプに対応 2つの非バッファー2 v 184ピンddr sdram dimm ソケットを搭載 合計で最大2gbまでの容量に対応可能 74
- プロセッサ 74
- メモリ 74
- ーレート動作が可能で 双方向の 2000 1600 1200 800 400 mt 秒の転送率を実現 74
- 日本語 74
- 機能 74
- 転送率が2000 1600 1200 800 400 mt 秒 74
- 高品質の差動式cd入力をサポート 74
- Biosファームウェア 75
- Multi language translation 75
- オンボードlan オプション 75
- 拡張オプション 75
- 日本語 75
- 統合i o 75
- K8t890 76
- Multi language translation 76
- Vt8237 76
- 메모리 76
- 오디오 코덱 76
- 칩셋 76
- 칩셋 패밀 76
- 특징 76
- 프로세서 76
- Bios 펌웨어 77
- Multi language translation 77
- 온보드 lan 선택 품목 77
- 통합 i o 77
- 확장 옵션 77
- Multi language translation 78
- 功能 78
- 晶片組 78
- 繁體中文 78
- 處理器 78
- 記憶體 78
- 音頻編碼器 78
- Bios 韌體 79
- Multi language translation 79
- 擴充選項 79
- 整合 i o 79
- 機載 區域網路 選購 79
- 繁體中文 79
- Multi language translation 80
- 内存 80
- 功能 80
- 处理器 80
- 简体中文 80
- 芯片组 80
- 音频编解码器 80
- Multi language translation 81
- Onboard lan 可选 81
- 扩展选项 81
- 简体中文 81
- 集成 i o 81
- Multi language translation 82
- Аудио codec 82
- Память 82
- Процессор 82
- Русский 82
- Характеристики 82
- Чипсет 82
- Multi language translation 83
- Возможности расширения 83
- Встроенный сетевой адаптер lan опционально 83
- Интегрированный вход выход 83
- Русский 83
- Audio codec 84
- Chipset 84
- Multi language translation 84
- Pamięć 84
- Polski 84
- Procesor 84
- Firmowy bios 85
- Możliwości rozbudowy 85
- Multi language translation 85
- Polski 85
- Zintegrowana obsługa sieci lan opcjonalnie 85
- Zintegrowane we wy 85
- Multi language translation 86
- Paměť 86
- Procesor 86
- Vlastnosti 86
- Zvukový kodek 86
- Česky 86
- Čipová sada 86
- Firmware bios 87
- Integrovaný vstup výstup 87
- Možnosti rozšíření 87
- Multi language translation 87
- Vestavění síťové rozhraní lan volitelně 87
- Česky 87
- Audio codec 88
- Caracteristici procesorul 88
- Memoria 88
- Multi language translation 88
- Română 88
- Setul de chipuri 88
- Firmware bios 89
- I o integrată 89
- Multi language translation 89
- Onboard lan opţional 89
- Opţiuni de extindere 89
- Română 89
- Audio codec 90
- Multi language translation 90
- Български 90
- Памет 90
- Процесор 90
- Спецификация 90
- Чипсет 90
- Bios firmware 91
- Multi language translation 91
- Български 91
- Възможности за разширяване 91
- Интегриран вход изход контролер 91
- Интегриран мрежов контролер опция 91
- Audio codec 92
- Jellemző processzor 92
- Lapkakészlet 92
- Magyar 92
- Memória 92
- Multi language translation 92
- Alaplapon levő lan választható 93
- Beépített i o 93
- Bios firmware 93
- Bővítési lehetőségek 93
- Magyar 93
- Multi language translation 93
Похожие устройства
- ECS Elitegroup RS482-M Руководство пользователя
- ECS Elitegroup NFORCE3-A939 Руководство пользователя
- ECS Elitegroup NFORCE4-A939 Руководство пользователя
- ECS Elitegroup RX480-A Руководство пользователя
- ECS Elitegroup KA1 MVP Руководство пользователя
- ECS Elitegroup KN1 Extreme Руководство пользователя
- ECS Elitegroup KN1 SLI Lite Руководство пользователя
- ECS Elitegroup KN2 SLI Руководство пользователя
- ECS Elitegroup D6VAA Руководство пользователя
- ECS Elitegroup MB694A Руководство пользователя
- ECS Elitegroup X79R-AX Руководство пользователя
- ECS Elitegroup X79R-AX Deluxe Руководство пользователя
- ECS Elitegroup A55F-A Руководство пользователя
- ECS Elitegroup A55F-A2 Руководство пользователя
- ECS Elitegroup A55F-M2 (V1.0A) Руководство пользователя
- ECS Elitegroup A55F-M2 (V2.0) Руководство пользователя
- ECS Elitegroup A55F-M3 Руководство пользователя
- ECS Elitegroup A55F-M4 (V1.0) Руководство пользователя
- ECS Elitegroup A55F-M4 (V2.0) Руководство пользователя
- ECS Elitegroup A75F-A Руководство пользователя