Home
Главная
Microlife
Тонометр
3BT0-H
Инструкция по эксплуатации Страница: 6

Microlife 3BT0-H Инструкция по эксплуатации онлайн [6/30] 179997

5.7. Memory – displaying the last measurement

The blood-pressure monitor automatically stores the last

measurement value. By pressing the MEMORY button for

at least 3 seconds, the last measurement will be

displayed.

☞ Further information

Measurements should not occur soon after each other, since otherwise, the results will be falsified. Wait

therefore for at least 1 minute in a relaxed position, sitting or lying, before you repeat a measurement.

6. Error messages/malfunctions

If an error occurs during a measurement, the measurement is

discontinued and a corresponding error code is displayed.

(example: error no. 1)

Error No. Possible cause(s)

ERR 1 The systolic pressure was determined but afterwards the cuff pressure fell below

20 mmHg. This situation can occur, for example, if the tube becomes unplugged af-

ter the systolic blood-pressure has been measured.

Further possible cause: No pulse has been detected

ERR 2 The pressure dropped below 20 mmHg without a measurement taking place. The

Release valve was pressed during the measurement.

ERR 5 The measured readings indicated an unacceptable difference between systolic and

diastolic pressures. Take another reading following directions carefully. Contact

you doctor if you continue to get unusual readings.

d) After the inflation process lay down the pump ball

and remain in a quiet and relaxed sitting position. The

measurement now proceeds on its own. If no measu-

rement takes place and all that appears in the display

is a flashing, upwards pointing arrow, see below

under «Inflate further». When the instrument detects

a pulse, a heart symbol in the display starts to flash

and a beep is heard for every heart beat.

e) When the measurement has been concluded, a long

peep tone sounds. The measured systolic and

diastolic blood-pressure values as well as the pulse

frequency are now displayed.

The cuff pressure can now be quickly released by

pressing the release valve at the pump ball.

5.5. Inflating further

If the cuff is not inflated sufficiently, the measurement is

broken off after a few seconds and a flashing arrow

pointing upwards appears in the display.

It is then necessary to inflate further to at least 20 mmHg

higher than the previous value.

The instruction to inflate further can appear several times

if the pressure is still not sufficient.

Attention:

If the cuff is inflated too far (over 300 mmHg), «HI»

appears in the display and a warning signal is sounded.

The cuff pressure must then be immediately released

using the quick-release valve) at the pump ball)!

As soon as the cuff is inflated sufficiently and the

measurement is proceeding, continue as described under

points d–e.

5.6. Discontinuing a measurement

If it is necessary to interrupt a blood pressure measure-

ment for any reason (e.g. the patient feels unwell), press

the quick release valve at the pump ball. The device then

immediately lowers the cuff-pressure automatically.

3 sec.

Содержание

Похожие устройства

d After the inflation process lay down the pump ball and remain in a quiet and relaxed sitting position The measurement now proceeds on its own If no measu rement takes place and all that appears in the display is a flashing upwards pointing arrow see below under Inflate further When the instrument detects a pulse a heart symbol in the display starts to flash and a beep is heard for every heart beat 5 7 Memory displaying the last measurement The blood pressure monitor automatically stores the last measurement value By pressing the MEMORY button for at least 3 seconds the last measurement will be displayed e When the measurement has been concluded a long peep tone sounds The measured systolic and diastolic blood pressure values as well as the pulse frequency are now displayed The cuff pressure can now be quickly released by pressing the release valve at the pump ball ir Further information Measurements should not occur soon after each other since otherwise the resultswill be falsified Wait therefore for at least 1 minute in a relaxed position sitting or lying before you repeat a measurement 5 5 Inflating further If the cuff is not inflated sufficiently the measurement is broken off after a few seconds and a flashing arrow pointing upwards appears in the display It is then necessary to inflate further to at least 20 mmHg higher than the previous value The instruction to inflate further can appear several times If an error occurs during a measurement the measurement is discontinued and a corresponding error code is displayed example error no 1 6 Error messages malfunctions if the pressure is still not sufficient Attention If the cuff is inflated too far lover 300 mmHg HI appears in the display and a warning signal is sounded The cuff pressure must then be immediately released using the quick release valve at the pump ball As soon as the cuff is inflated sufficiently and the measurement is proceeding continue as described under points d e Error No ERR1 ERR 2 ERR 5 Possible cause s The systolic pressure was determined but afterwards the cuff pressure fell below 20 mmHg This situation can occur for example if the tube becomes unplugged af ter the systolic blood pressure has been measured Further possible cause No pulse has been detected The pressure dropped below 20 mmHg without a measurement taking place The Release valve was pressed during the measurement The measured readings indicated an unacceptable difference between systolic and diastolic pressures Take another reading following directions carefully Contact you doctor if you continue to get unusual readings 5 6 Discontinuing a measurement If it is necessary to interrupt a blood pressure measure ment for any reason e g the patient feels unwell press the quick release valve at the pump ball The device then immediately lowers the cuff pressure automatically 0 9

Скачать