DWT abs-14,4 sli bmc [16/136] English
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

DWT abs-14,4 sli bmc [16/136] English

DWT abs-14,4 sli bmc [16/136] English
• Mount / replace the accessory. • Fig. 10.4 - (the green indicator 16 is blinking, the
• Tighten the keyless chuck 1 without skewing the
battery 9 is inserted in the charger 11) - the charging
process of the battery 9 is terminated due to
accessory as it is shown in figures 1-2.
inappropriate temperature. When the temperature
conditions are normal, the process of charging will
Mounting / dismounting of the keyless chuck (see
resume.
fig. 3-6)
• Fig. 10.5 - (the red indicator 15 is blinking, the battery 9
is inserted in the charger 11) - the charging process of
• To mount the keyless chuck 1, carry out the
the battery 9 is terminated because of its failure.
operations in consecutive stages as it is shown in
Replace the faulty battery 9, its further use is prohibited.
figures 3-5.
• To dismount the keyless chuck 1, carry out the
In the process of charging the battery 9
operations in consecutive stages as it is shown in
and the charger 11 become hot, it is a
figures 4-6.
normal process.
Attention: keep in mind that in the
Switching the power
tool on / off
process of mounting / dismounting of the
keyless chuck 1 the screw 12 has a left-
Make sure that the reverse switch 7 is not centred;
hand thread.
this blocks on / off switch 6.
Screwdriver bit / magnetic holder (see fig. 7)
Switching on:
Press on / off switch 6.
For short screwdriver bits use the magnetic
Switching off:
holder 13 for their reliable fixing (see fig. 7).
Release the on / off switch 6.
A magnetic holder 13 is not needed for extended
screwdriver bits 2 (specially purposed for
Design features
screwdrivers).
of the power tool
Charging procedure
Battery (see fig. 11)
of the power tool battery
• Li-Ion battery 9 can be put on and remove from
Initial operation of the power tools
charger 11 at any time (regardless of the charging state) -
it does not affect its service life and it does not lead to
The power tool is supplied with a partially charged
the loss of its capacity.
battery 9. Before the first use, the battery 9 must be
• The battery 9 is protected by the safety system
fully charged.
against deep discharge. In case of complete discharge,
the power tool is automatically switched off. Attention:
The battery 9 must be charged in the
do not try to switch on the power tool when the
appropriate temperature (from 0°C to
protection system is activated the battery 9 can be
45°C).
damaged.
Charging process (see fig. 8-9)
[ABS-14,4 SLi, ABS-18 SLi, ABS-14,4 TLi, ABS-18 TLi]
• Centre the reverse switch 7.
With the push of the button 18 the indicators 17 show
• Connect the charger 11 to the power supply.
the state of charge of the battery 9 (see fig. 11).
• Press the battery lock 10 (ABS-10,8 Li - two battery
locks 10), remove the battery 9 and insert it in the
Temperature protection
charger 11 (see fig. 8-9).
The temperature protection system enables to
• When battery is fully charged, disconnect the battery 9
from the charger 11 and mount it in the power tool.
automatically deactivate the power tool in case of
excess load or when the temperature of the battery 9 is
• Switch off the charger 11 after use.
exceeding 70°C. The system guarantees protection of
the power tool from damage in case of noncompliance
Charger indicators (see fig. 10)
with the operation conditions.
Charger indicators 15 and 16 inform of the battery 9
LED lamp
charging process. Signals of the indicators 15 and 16
are shown on the label 14 (see fig. 10.1-10.5).
When the on / off switch 6 is pushed, the LED lamp 3 is
• Fig. 10.1 - (the green indicator 16 is on, the battery 9 is
automatically switched on that allows to carry out works
not inserted in the charger 11) - the charger 11 is
in low light conditions.
connected to the power network.
• Fig. 10.2 - (the red indicator 15 is on, the battery 9 is
Torque regulator
inserted in the charger 11) - the battery 9 is being charged.
• Fig. 10.3 - (the green indicator 16 is on, the battery 9 is
Rotate the regulator 4 in order to set one of the 18
inserted in the charger 11) - the battery 9 is fully charged.
torque values most suitable for the work performed.
English
16

Содержание

Похожие устройства

Скачать