Hotpoint-Ariston ct ntc ix2 [12/65] Important

Hotpoint-Ariston ct ntc ix2 [12/65] Important
hotpoint.eu
14
en
pulling it out as per illustration.
The lter cartridge can be disposed of
with normal household waste.
Before installing the new ltering car-
tridge, wash the plastic lter body with a
washing up liquid and rinse thoroughly.
C11
Remove the new lter cartridge from the
packagingandtitbyrmlypushingitintothel-
terhead,makingsureitisrmlyandsecurelyt-
ted.Makesurethenewlteryouarettingcomes
in a sealed bag for hygienic purposes.
C12
Screwthelterheadandthelterbodyto-
gether,makingsureitisrmlytightened.
C13
Fitthelterassemblywiththebackintothe
appliance as follows:
1. Insertthelterassemblybackintoitscradle,
aligning the two male spigots with the female
holesinthecradle.Pushrmlyuntilthelter
sitssnuglyandisushinsidethecradleand
with the cradle top surface.
2. Lockthelterbyclosingthelockingleverun-
tilit‘clicks’intoplace
3. Rotate the red rotating lever back into the
LOCK position.
C14
Re-tthelid,makingsurethefrontisatta-
chedrst.Ifthelidisnotttedcorrectlytheunit
will not switch on.
Fit the lid making sure the front is
pushed in place rst and then push the
back end with the screws down to give a snug
t.
C15
Re-tthetwoscrewsthatholdtheliddown
using the screwdriver.
The screws should be hand tightened,
do not over tighten.
C16
Insert the plug into the mains socket and
press and hold the dispense button for 10 secon-
dsuntilyouhearabeepasthiswillresetthelter
timer.
If the reservoir contains water, place a
cup or container under the dispense
C5
ToremovetheUVlamprmlypullitupand
out. Do not pull the lamp out at an angle as it may
breakordamagetheinternalpartsoftheapplian-
ce.
The UV lamp must be disposed of cor-
rectly and must not be disposed of with
normal household waste.
C6
Insert the new UV lamp while holding the
white end caps only. Insert the UV lamp as shown
in the illustration and push it all the way down until
it cannot go any further.
Do not use force when removing and in-
serting the UV lamp as you may damage
internal parts. Do not touch the UV lamp glass
surface with your ngers as this will affect the
performance of the UV lamp.
C7
Re-connecttheUVlampconnectormaking
sure the connectors are lined up correctly as they
willonlyttogetherwhencorrectlyaligned.
Pay attention not to wet the UV lamp
connector; in case of water drops on UV
lamp connectors, do not reconnect to power
mains before drying completely.
Wear disposable gloves during the ope-
rations of lter removal hereafter descri-
bed to avoid the direct contact with wet parts.
C8
To remove the Filter, do the following:
1. Rotate the red rotating lever so that it is pa-
rallel with the side panel.
2. Insertyourngerintotheroundholeofthe
lever, and pull the lever up to the vertical
position.
3. Pull the lever straight up to remove the Filter
assembly (some slight force may be requi-
red).
C9
Unscrewthelterbodyfromthelterhead
byturningthebaseinaanticlockwisedirectionas
per the illustration.
Be careful as the lter body will contain
water.
C10
Removetheltercartridgefromtheheadby

Содержание

Похожие устройства

Скачать