Vitek VT-1891 BK [5/24] English
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Vitek VT-1891 BK [5/24] English

Vitek VT-1891 R [5/24] English
5
E N G L I S H
cushions, but for collecting dust from furniture
surface as well, the pile on the brush (24) pre-
vents damage of polished furniture surface.
Using the dustbag
1 cloth dustbag and 3 paper dustbags are sup-
plied with the unit.
• Open the dustbag compartment lid (16) by
pressing the clamp (17).
• Take the dustbag holder (23) and pull it
to remove dustbag holder (23) from the
clamps (22).
• To install the dustbag (26) back to its place,
insert the dustbag holder (23) into the
clamps (22).
• Close the dustbag compartment lid (16).
Note: Always make sure that the dustbag (26)
is installed properly before closing the dustbag
compartment lid (16).
USING THE VACUUM CLEANER
Safety measures
• Do not use the vacuum cleaner near hot
surfaces, ashtrays and in the places where
inflammable liquids are stored.
• If the suction power of the vacuum cleaner
decreases rapidly while cleaning, switch the
vacuum cleaner off immediately and check
the telescopic pipe and the flexible hose for
obstruction. Switch the vacuum cleaner off,
then unplug it, remove the obstruction and
only after that continue cleaning.
USING THE VACUUM CLEANER
Attention! Always switch the vacuum cleaner
on only with the dustbag (26) and inlet (21)
and outlet (12) filters installed. Always
make sure that the filters are installed pro-
perly.
• Before using the unit, unwind the power cord
to the required length and insert the power
plug into the mains socket.
• The yellow mark on the power cord indicates
the maximum cord length. Do not unwind the
power cord further than the red mark.
• Press the ON/OFF button (9) to switch the
vacuum cleaner on.
• During the operation you can control the
suction power using the suction power con-
trol (10).
• After room cleaning switch the vacuum
cleaner off by pressing the ON/OFF button
(9) and unplug the unit.
• To wind the cord press the cord winding but-
ton (11), hold the winding cord with your hand
to avoid its whipping and damage.
CLEANING AND CARE
• If full dustbag indicator (13) turns «red» during
operation, replace the paper dustbag or clean
up the cloth dustbag.
• Before cleaning or replacing the dust-
bag (26) switch the vacuum cleaner off and
unplug it.
• Provide that the inlet filter (21) and the outlet
HEPA filter (12) are always clean, because the
overall performance of the vacuum cleaner
depends on it; clean the filters no less than
3-4 times a year, and more often at severe
obstruction.
Cleaning the inlet filter (21)
• Switch the vacuum cleaner off and unplug it.
• Open the dustbag compartment lid (16) by
pressing the clamp (17). Remove the dust-
bag (26).
• Take the inlet filter (21) and remove it from the
holders (20) pulling it upwards.
• Wash the inlet filter (21) with warm water, dry
thoroughly and install it into the filter hold-
ers (20).
• Install the dustbag (26) back to its place.
• Close the dustbag compartment lid (16).
Cleaning the outlet HEPA filter (12)
• Switch the vacuum cleaner off and unplug it.
• Remove the outlet filter grid (7) by pressing
the clamp (8) and remove the HEPA filter (12).
• Wash the HEPA Filter (12) under slightly warm
water jet. Do not wash the HEPA filter (12) in a
dishwashing machine.
• Dry the HEPA filter (12). Do not dry the HEPA
filter with a hairdryer.
• Install the HEPA filter (12) back to its place.
• Install the outlet filter grid (7) back to its place.
Notes:
– Before installing the filters (12, 21) make sure
that they are dry.
– Do not dry the filters (12, 21) with a hairdryer.
Vacuum cleaner body
– Wipe the vacuum cleaner body with a soft,
slightly damp cloth and then wipe it dry.
– Do not immerse the body of the vacuum
cleaner, the power cord and the power plug
of the unit into water or other liquids. Provide
VT-1891.indd 5 03.12.2015 10:51:01

Содержание

Похожие устройства

Скачать