![Timberk tgh 4200 x0 Инструкция по эксплуатации онлайн [6/24] 201172](/img/pdf.png)
Timberk tgh 4200 x0 Инструкция по эксплуатации онлайн [6/24] 201172
![Timberk tgh 4200 x0 Инструкция по эксплуатации онлайн [6/24] 201172](/views2/1239617/page6/bg6.png)
www.timberk.com • gas heater
6
Device control
Connecting the gas heater
1. Check for proper assembly and installation of the gas heater, and the
accession gas tank instructions below
2. Gently remove the valve gas cylinder and check for gas leaks with
soapy water. The formation of bubbles indicates the presence of a gas
leak in the wiring. In this case, replace the valve of the gas container,
immediately contact an authorized service center Timberk to fix this
problem
3. Turn the gas valve of heater counterclockwise until it stops at maximum
power and push it in. (fig.2)
4. Fast light radiating heater on the obverse ceramic panel with the ignition
matches or lighters (Attention! there is a risk of fire, be extremely careful.
Hold the gas valve in the clamped position for 10 seconds. If the burner
goes out, wait 5-10 minutes and repeat the above steps again.
5. To adjust the power level, heating and/or installation minimum power
turn the gas valve to the heater clockwise.
Gas valve of heater
Turn-off gas heater
1. Tighten the gas valve on a gas cylinder to another. Thus the supply of
gas to the gas heater must cease.
2. Turn the gas valve to the heater clockwise until it stops.
3. Ensure that no flame before the ceramic panel heater.
1. Make sure that the heater is switched off.
2. If it is necessary to replace an empty gas cylinder, shut gas screwing the
gas check valve on the cylinder clockwise up to the stop.
3. Remove the cylinder clamp and take the cylinder out of the heater body.
4. Remove the gas pressure reducer from the cylinder unscrewing its cap
nut.
5. Connect and install a full gas cylinder as indicated in Section
6. Preparation for work.
IMPORTANT!
Never disconnect the gas regulator (reducer) from a gas
bottle at the time of the heater. Before disconnecting
always check no flame on a gas burner.
IMPORTANT!
For some time after turning off the device remains hot.
Do not touch the appliance with bare hands, cover the
device, move or lift it.
IMPORTANT!
Do not smoke during replacement of the cylinder.
Do not replace the cylinder, if there is an open flame
source nearby.
Keep gas cylinders in a separate well-ventilated room
far from combustible materials. It is prohibited to store
and operate gas cylinders in flats of high-rise buildings,
cellars, garrets.
Fig. 2
Increase
power
Decrease
power
Похожие устройства
- Timberk swh red3 100 v Инструкция по эксплуатации
- Timberk swh red3 80 v Инструкция по эксплуатации
- Timberk swh red3 50 v Инструкция по эксплуатации
- Timberk swh re9 80 v Инструкция по эксплуатации
- Timberk swh re9 50 v Инструкция по эксплуатации
- Timberk swh re9 30 v Инструкция по эксплуатации
- Timberk swh re9 100 v Инструкция по эксплуатации
- Timberk swh ms2 10 hu Инструкция по эксплуатации
- Timberk swh fsq1 80 v Инструкция по эксплуатации
- Timberk swh fsq1 50 v Инструкция по эксплуатации
- Timberk swh fsq1 30 v Инструкция по эксплуатации
- Timberk swh fsq1 100 v Инструкция по эксплуатации
- Timberk swh fsp1 80 v Инструкция по эксплуатации
- Timberk swh fsp1 50 v Инструкция по эксплуатации
- Timberk swh fsp1 30 v Инструкция по эксплуатации
- Timberk swh fsp1 100 v Инструкция по эксплуатации
- Timberk swh fsm6 80 h Инструкция по эксплуатации
- Timberk swh fsm6 50 h Инструкция по эксплуатации
- Timberk swh fsm6 30 h Инструкция по эксплуатации
- Timberk swh fsm5 80 v Инструкция по эксплуатации
Скачать
Случайные обсуждения