Timberk tef w16 wc2 [5/6] English

Похожие устройства

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIM ENGLISH llllllllllllllllll II llllllllllllllllll llllllllllllllllll II llllllllllllllllll II llllllllllllllllll llllllllllllllllll II llllllllllllh 3 GENERAL DESCRIPTION Q ATTENTION 1 Front grille 2 Propeller screw 3 Propeller 4 Back grille screw 5 Clamp 6 Back grille 7 Motor shaft 8 Dowel 9 Electric motor 10 Back end of electric motor body 11 Swivel joint 12 Power cord 13 Body 14 Back support 15 Rubber base lô Remote control board for model TEFW1 6WM2 1 Control panel 18 Control cord for model TEF W1 6 WC2 The manufacturer reserves the right to introduce structural alterations not deteriorating the fan quality and reliability without anyspecial notification Appliance control with the use of control cord Below you can see two control cords One cord switches the fan on changes speed and switches the appliance off The other cord controls the fan turning in horizontal direction Control panel for model TEFW1 6WC2 For model TEF W16 WM1 appliance control with the use of control panel Pressing buttons Mode Timer On Off Speed and Osc on the control panel you may control modes of the fan operation Control panel for model TEF W1 6 WM2 4 ASSEMBLY see Fig 1 1 Release a propeller screw 2 by turning it clockwise and a back grille screw by turning it counterclockwise 2 Mount a back grille 6 on a motor shaft 7 by matching three apertures in the back grille with three dowels 8 on the front of the electric motor Press the dowels tightly into the apertures 3 Attach the back grille 6 to the electric motor body with the use of a screw 4 4 Mount a propeller 3 on the motor shaft 7 by matching grooves on the propeller with a dowel on the shaft and fix the propeller 3 with the use of the propeller screw 2 by turning it counterclockwise 5 Checkthe propeller rotation by revolving it with a hand Make sure that there is no friction in the point of connection with the back grille screw The propeller should revolve freely Otherwise repeat actions from clause 1 6 Match the front grille 1 with the back one 6 and slip on the hooks located on the front grille and clutch them with clamps located on the front grille 5 FAN MOUNTING ON THE WALL 1 Mount a bracket on the wall with the use of three screws 2 Hang the fan on the bracket 1 On Off switching the appliance on and off 6 OPERATION 2 Speed control of blow off speed Low low speed Medium medium speed High high speed For model TEF W16 WC1 appliance control with the use of control panel 4 Timer setting of disconnection timer up to 4 hours 1 After voltage check connect the appliance to a power source 2 Select operation speed with the use of a switch on the control panel by setting it to any of the following positions lowspeed medium speed or high speed 3 To stop the appliance operation set the switch to OFF position 0 3 Osc control of rotation angle in horizontal direction S Mode control of the appliance modes Normal manual mode Natural Natural wind mode Sleep Wind for sleep mode In lower part on the panel there are indicator lamps Depending on which lamp is flashing you may define the mode of the fan operation and or for how many hours the timer has been set Fig 1 8 www timberk ru electric wall fan www timberk ru electric wall fan 9 llllllllllllllll

Скачать