Makita DJR187Z [7/60] Assembly
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Makita DJR187Z [7/60] Assembly

Makita DJR187Z [7/60] Assembly
7 ENGLISH
• For high speed
Whenthelock/speedchangeleverisdepressed
fromAside,thestrokespeedisat“2”.
• For low speed
Whenthelock/speedchangeleverisdepressed
from B side, the stroke speed is at “1”.
Whenthelock/speedchangeleverisin
position, the
toolislockedandtheswitchtriggercannnotbepulled.
Lighting up the front lamp
►Fig.6: 1. Lamp
CAUTION: Do not look in the light or see the
source of light directly.
Pulltheswitchtriggertolightupthelamp.Thelamp
keepsonlightingwhiletheswitchtriggerisbeingpulled.
Thelampgoesoutapproximately10secondsafter
releasing the switch trigger.
NOTE: Use a dry cloth to wipe the dirt off the lens of
the lamp. Be careful not to scratch the lens of lamp, or
it may lower the illumination.
NOTE:Whenthetoolisoverheated,thelampblinks
foroneminute.Inthiscase,cooldownthetoolbefore
another operation.
Adjusting the shoe
Whenthereciprosawbladelosesitscuttingefciency
in one place along its cutting edge, reposition the shoe
to utilize a sharp, unused portion of its cutting edge.
Thiswillhelptolengthenthelifeofthereciprosaw
blade.
Thepositionoftheshoecanbeadjustedinvelevels.
Torepositiontheshoe,opentheshoeadjustinglever
andselectthesuitableposition,thenclosetheshoe
adjustinglever.
►Fig.7: 1. Shoe 2.Shoeadjustinglever
NOTE:Theshoecannotbeadjustedwithoutopening
theshoeadjustingleverfully.
Hook
CAUTION: When hanging the tool, set the
lock/speed change lever in position to lock
the switch trigger. (See the section titled “Switch
action” .)
CAUTION: Never hang the tool at high or
potentially unstable location.
►Fig.8: 1. Hook
Thehookisconvenientforhangingthetooltemporarily.
Tousethehook,simplyliftuphookuntilitsnapsinto
the open position.
When not in use, always lower hook until it snaps into
the closed position.
ASSEMBLY
CAUTION: Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Installing or removing the recipro
saw blade
CAUTION: Always clean out all chips or for-
eign matter adhering to the blade and around the
blade clamp.Failuretodosomaycauseinsufcient
tighteningoftheblade,resultinginaseriousinjury.
Toinstallthereciprosawblade,alwaysmakesurethat
thebladeclamplever(partofthebladeclampsleeve)
is in released position ontheinsulationcoverbefore
insertingthereciprosawblade.Ifthebladeclamplever
isinxedposition,rotatethebladeclampleverinthe
directionofthearrowsothatitcanbelockedatthe
released positon
.
►Fig.9: 1. Blade clamp lever 2. Released position
3. Fixed position
Insertthereciprosawbladeintothebladeclampasfar
asitwillgo.Thebladeclampsleeverotatesandxes
thereciprosawblade.Makesurethatthereciprosaw
bladecannotbeextractedeventhoughyoutrytopull
it out.
►Fig.10: 1.Reciprosawblade2. Blade clamp sleeve
CAUTION: If you do not insert the recipro saw
blade deep enough, the recipro saw blade may be
ejected unexpectedly during operation.Thiscan
beextremelydangerous.
Toremovethereciprosawblade,rotatetheblade
clampleverinthedirectionofthearrowfully.Thereci-
prosawbladeisremovedandthebladeclampleveris
xedatthereleasedposition .
►Fig.11: 1.Reciprosawblade2. Blade clamp lever
CAUTION: Keep hands and ngers away from
the lever during the switching operation. Failure
to do so may cause personal injuries.
NOTE:Ifyouremovethereciprosawbladewithout
rotatingthebladeclampleverfully,thelevermaynot
belockedinthereleasedposition .Inthiscase,
rotatethebladeclampleverfullyagain,thenmake
surethatthebladeclampleverlockedatthereleased
position .
NOTE:Ifthebladeclampleverispositionedinside
thetool,switchonthetooljustasecondtoletthe
bladeoutasshowninthegure.Removethebattery
cartridgefromthetoolbeforeinstallingorremoving
thereciprosawblade.

Содержание

Похожие устройства

Скачать