Makita HS6601 [10/56] Maintenance
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Makita HS6601 [10/56] Maintenance

Makita HS6601 [10/56] Maintenance
10 ENGLISH
Holdthetoolrmly.Thetoolisprovidedwithbothafront
gripandrearhandle.Usebothtobestgraspthetool.
Ifbothhandsareholdingsaw,theycannotbecutby
thecircularsawblade.Setthebaseontheworkpiece
tobecutwithoutthecircularsawblademakingany
contact. Then turn the tool on and wait until the circular
sawbladeattainsfullspeed.Nowsimplymovethetool
forwardovertheworkpiecesurface,keepingitatand
advancing smoothly until the sawing is completed.
To get clean cuts, keep your sawing line straight and
your speed of advance uniform. If the cut fails to prop-
erly follow your intended cut line, do not attempt to turn
orforcethetoolbacktothecutline.Doingsomaybind
thecircularsawbladeandleadtodangerouskickback
andpossibleseriousinjury.Releaseswitch,waitforcir-
cularsawbladetostopandthenwithdrawtool.Realign
tool on new cut line, and start cut again. Attempt to
avoid positioning which exposes operator to chips and
wooddustbeingejectedfromsaw.Useeyeprotection
tohelpavoidinjury.
Rip fence (Guide rule)
Optional accessory
►Fig.22: 1.Ripfence(Guiderule)2. Clamping screw
The handy rip fence allows you to do extra-accurate
straight cuts. Simply slide the rip fence up snugly
against the side of the workpiece and secure it in posi-
tionwiththeclampingscrewonthefrontofthebase.It
alsomakesrepeatedcutsofuniformwidthpossible.
MAINTENANCE
CAUTION: Always be sure that the tool is
switched off and unplugged before attempting to
perform inspection or maintenance.
CAUTION: Clean out the guard to ensure
there is no accumulated sawdust and chips
which may impede the operation of the guarding
system. A dirty guarding system may limit the proper
operation which could result in serious personal
injury.Themosteffectivewaytoaccomplishthis
cleaning is with compressed air. If the dust is being
blown out of the guard, be sure the proper eye
and breathing protection is used.
NOTICE: Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
Adjusting the parallelism
►Fig.23: 1. Screw
Thisadjustmenthasbeenmadeatthefactory.Butifitis
off,youcanadjustitasthefollowingprocedure.
1. Make sure all levers and screws are tightened.
Slightly loosen the screw illustrated.
2. While opening the lower guard, move the rear of
thebasesothatthedistanceAandBbecomesequal.
3. Tighten the screws and make a test cut to check
the parallelism.
Adjusting 0°-cut accuracy
►Fig.24: 1.Adjustingbolt
►Fig.25: 1. Triangular rule 2. Clamping screw
Thisadjustmenthasbeenmadeatthefactory.Butifitis
off,youcanadjustitasthefollowingprocedure.
1. Slightly loosen the clamping screws on the front
and rear of the tool.
2.
Makethebaseperpendiculartothebladeusinga
triangularruleorsquarerulebyturningtheadjustingbolt.
3. Tighten the clamping screws and make a test cut
to check the verticalness.
Replacing carbon brushes
►Fig.26: 1. Limit mark
Checkthecarbonbrushesregularly.
Replacethemwhentheyweardowntothelimitmark.
Keepthecarbonbrushescleanandfreetoslipinthe
holders.Bothcarbonbrushesshouldbereplacedatthe
sametime.Useonlyidenticalcarbonbrushes.
1. Useascrewdrivertoremovethebrushholder
caps.
2. Takeouttheworncarbonbrushes,insertthenew
onesandsecurethebrushholdercaps.
►Fig.27: 1. Brush holder cap
TomaintainproductSAFETYandRELIABILITY,
repairs,anyothermaintenanceoradjustmentshould
beperformedbyMakitaAuthorizedorFactoryService
Centers, always using Makita replacement parts.
OPTIONAL
ACCESSORIES
CAUTION:
These accessories or attachments are
recommended for use with your Makita tool specied in
this manual. The use of any other accessories or attach
-
mentsmightpresentariskofinjurytopersons.Onlyuse
accessory or attachment for its stated purpose.
If you need any assistance for more details regarding these
accessories, ask your local Makita Service Center.
• Circularsawblade
• Ripfence(Guiderule)
• Hex wrench
• Dust nozzle
• Guiderail
• Bevel guide
• Clamp
• Sheet
• Rubbersheet
• Position sheet
• Guiderailadapter
• Rulebar
NOTE:Someitemsinthelistmaybeincludedinthe
tool package as standard accessories. They may
differ from country to country.

Содержание

Похожие устройства

Скачать