Vitek VT-1819 SR [5/48] English
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Vitek VT-1819 SR [5/48] English

Vitek VT-1819 SR [5/48] English
5
E N G L I S H
THE UNIT IS INTENDED FOR HOUSEHOLD US-
AGE ONLY
ASSEMBLING OF THE VACUUM CLEANER
After the unit transportation or storage at low tem-
perature it is necessary to keep it for at least two
hours at room temperature before switching on.
– Unpack the vacuum cleaner completely and
check it for damages. Do not use the unit in
case of damages.
– Before connecting the battery charging base
(13) to the mains, make sure that voltage in
your mains corresponds to the unit operat-
ing voltage.
Assembling of the battery charging base
(13)
– To assemble the base (13) insert the vertical
stand into the bottom part of the base (13) till
the clamp clicking (pic. 1). We recommend
to place the assembled base (13) as close
to the wall as possible. To disassemble the
base press the clamp and pull the vertical
stand upwards.
Assembling of the electric brush
– Connect the handle (2) to the unit body and
fix it with a screw (pic. 2).
– Insert the electric brush (12) into the air inlet
in the bottom part of the unit body (pic. 3)
till the clamp clicking. To detach the electric
brush (12) press the clamp (11) and remove
the brush.
– Install the portable vacuum cleaner into the
electric brush body (pic. 4), it will be fixed. To
detach the portable vacuum cleaner take the
handle (6) and press the release button (3).
– Set the electric brush on the charging base
(13) (pic. 5).
BATTERY CHARGING
For proper battery operation the unit is provided
with control system: the vacuum cleaner will be
switched off if the battery voltage goes below
the set value.
– Place the base (13) as close to the wall and
the socket as possible, and set the assem-
bled vacuum cleaner with electric brush on
the base (13).
– Insert the power plug into the socket, the
charge indicator (7) will light up. While bat-
tery charging the indicator (7) is glowing red;
the green color of the indicator (7) means
that charging is finished .
– Pull the power plug out of the socket after the
battery charging.
– Always unplug the base after the battery
charging.
– You can adjust the power cord length, wind-
ing it over the cord storage (14).
More tips
– The first three charging of a new battery
should be performed after its total discharg-
ing (when you even cannot switch the vacu-
um cleaner on).
– Duration of every charging cycle should be
not less than 12 hours.
– The following charging cycles can be stopped
once the indicator (7) lights up green.
Notes:
– It’s impossible to use the vacuum cleaner
during the battery charging.
– Do not detach the portable vacuum cleaner
from the electric brush body and the brush
from the base (13) during the battery charg-
ing.
– Flashing of brush indicator (12) means that
the control scheme works improperly. In this
case unplug the unit and apply to the autho-
rized service center.
OPERATION
Safety measures
– Do not use the vacuum cleaner near hot
surfaces, ashtrays and in the places where
inflammable liquids are stored.
– Take sharp objects away from the floor before
cleaning to prevent unit damage.
Attention! Do not use the vacuum cleaner, if the
separator (20), the HEPA filter (18) and the foam
filter (19) are not installed in the dust bin (10).
Using of the vacuum cleaner with electric
brush
Use the electric brush (12) for cleaning hard
floors, linoleum, tile floor and carpets with low
pile.
– Detach the vacuum cleaner from the base.
– Switch the unit on by pressing the button (1),
the operation indicators of the portable vac-
uum cleaner (7) and electric brush (12) will
VT-1819 SR.indd 5 13.12.2012 15:26:16

Содержание

Похожие устройства

Скачать