![Gigabyte Z370 AORUS GAMING WIFI [19/52] M2p_32g m2q_32g m socket 3 connectors](/img/pdf.png)
Gigabyte Z370 AORUS GAMING WIFI [19/52] M2p_32g m2q_32g m socket 3 connectors
![Gigabyte Z370 AORUS GAMING WIFI [19/52] M2p_32g m2q_32g m socket 3 connectors](/views2/1307928/page19/bg13.png)
11) M2P_32G/M2Q_32G (M.2 Socket 3 Connectors)
The M.2 connectors support M.2 SATA SSDs or M.2 PCIe SSDs and support RAID conguration. Please
note that an M.2 PCIe SSD cannot be used to create a RAID set either with an M.2 SATA SSD or a SATA
hard drive. To create a RAID array with an M.2 PCIe SSD, you must set up the conguration in UEFI BIOS
mode. Refer to Chapter 3, "Conguring a RAID Set," for instructions on conguring a RAID array.
F_USB30
F_U
B_
F_ F_
_
B
BS_
B
SB_
B
_S
S_
_
B
_U
_
B
S
123
123
123
123
1
1
1
1
BSS
S
_S
SSU
1 2 3 4 5
S3
BSSS
U
__ 3
F_USB3F
S _
S _
S _
SF
B_
B_
F
_0
S
S
_0F
_F
_
_
__B
U
S _S
_
SF_
USB0_B
B_
F_USB3
F_USB303
_
_3U
80110 60 42
F_USB30
F_U
B_
F_ F_
_
B
BS_
B
SB_
B
_S
S_
_
B
_U
_
B
S
123
123
123
123
1
1
1
1
BSS
S
_S
SSU
1 2 3 4 5
S3
BSSS
U
__ 3
F_USB3F
S _
S _
S _
SF
B_
B_
F
_0
S
S
_0F
_F
_
_
__B
U
S _S
_
SF_
USB0_B
B_
F_USB3
F_USB303
_
_3U
80 60 42
InstallationNoticesforthePCIEX4,M.2andSATAConnectors:
Due to the limited number of lanes provided by the Chipset, the availability of the SATA connectors may
be affected by the type of device installed in the M2P_32G connector. The M2P_32G connector shares
bandwidth with the SATA3 0 connector. Refer to the following table for details.
Follow the steps below to correctly install an M.2 SSD in the M.2 connector.
Step 1:
Use a screw driver to unfasten the screw and nut from the motherboard. Locate the proper mounting hole
for the M.2 SSD to be installed and then screw the nut rst.
Step 2:
Slide the M.2 SSD into the connector at an angle.
Step 3:
Press the M.2 SSD down and then secure it with the screw.
Select the proper hole for the M.2 SSD to be installed and refasten the screw and nut.
M2P_32G
M2Q_32G
• M2Q_32G:
PCIEX4 SATA3 0 SATA3 1 SATA3 2 SATA3 3 SATA3 4 SATA3 5
M.2 PCIe SSD *
r
(Note)
a a a a a a
No M.2 SSD Installed
a a a a a a a
a: Available, r : Not available
* The M2Q_32G connector supports only PCIe SSDs.
Connector
Type of
M.2 SSD
• M2P_32G:
SATA3 0 SATA3 1 SATA3 2 SATA3 3 SATA3 4 SATA3 5
M.2 SATA SSD
r
a a a a a
M.2 PCIe SSD
a a a a a a
No M.2 SSD Installed
a a a a a a
a: Available, r : Not available
Connector
Type of
M.2 SSD
(Note) The PCIEX4 slot shares bandwidth with the M2Q_32G connector. The PCIEX4 slot becomes
unavailable when an SSD is installed in the M2Q_32G connector.
- 19 -
Содержание
- Rev 1001 12me z37agwf 1001r 1
- User s manual 1
- Z370 aorus gaming wifi 1
- See the latest safety and regulatory documents at gigabyte s website 2
- Wireless module country approvals 2
- Copyright 3
- Disclaimer 3
- Identifying your motherboard revision 3
- Chapter 1 hardware installation 4
- Chapter 2 bios setup 3 4
- Chapter 3 appendix 1 4
- Table of contents 4
- Z370 aorus gaming wifi motherboard layout 4
- Box contents 5
- Motherboard driver disk 5 i o shield 5
- Quick installation guide 5 one wi fi antenna 5
- User s manual 5 one g connector 5
- Z370 aorus gaming wifi 5
- Z370 aorus gaming wifi motherboard 5 four sata cables 5
- Z370 aorus gaming wifi motherboard layout 5
- 1 installation precautions 6
- Chapter 1 hardware installation 6
- 2 product specifications 7
- 2 productspecifications 7
- 3 installing the cpu 11
- 4 installing the memory 11
- Dualchannelmemoryconfiguration 11
- Installing the cpu 11
- 5 installing an expansion card 12
- 6 setting up amd crossfir 12
- 6 setting up amd crossfire nvidia sli configuration 12
- A system requirements 12
- B connecting the graphics cards 12
- C configuringthegraphicscarddriver 12
- Configuration 12
- 7 back panel connectors 13
- Hdmi port 13
- Ps 2 keyboard mouse port 13
- Rj 45 lan port 13
- Sma antenna connectors 1t1r 13
- Usb 3 gen 1 port 13
- Usb 3 gen 2 type a port red 13
- Usb type 13
- Center subwoofer speaker out 14
- Headphone 14
- Line in mic in 14
- Line out 14
- Optical s pdif out connector 14
- Rear speaker out 14
- 8 internal connectors 15
- 2 atx_12v_2x4 atx 2x4 12v power connector and 2x12 main power connector 16
- 4 cpu_fan sys_fan1 2 fan headers 16
- All fan headers on this motherboard are 4 pin most fan headers possess a foolproof insertion design when connecting a fan cable be sure to connect it in the correct orientation the black connector wire is the ground wire the speed control function requires the use of a fan with fan speed control design for optimum heat dissipation it is recommended that a system fan be installed inside the chassis 16
- Be sure to connect fan cables to the fan headers to prevent your cpu and system from 16
- Overheating overheating may result in damage to the cpu or the system may hang 16
- The 12v power connector mainly supplies power to the cpu if the 12v power connector is not connected the 12v power connector mainly supplies power to the cpu if the 12v power connector is not connected the computer will not start 16
- These fan headers are not configuration jumper blocks do not place a jumper cap on the headers 16
- To meet expansion requirements it is recommended that a power supply that can withstand high power consumption be used 500w or greater if a power supply is used that does not provide the required power the result can lead to an unstable or unbootable system 16
- With the use of the power connector the power supply can supply enough stable power to all the components on the motherboard before connecting the power connector first make sure the power supply is turned off and all devices are properly installed the power connector possesses a foolproof design connect the power supply cable to the power connector in the correct orientation 16
- Before installing the devices be sure to turn off the devices and your computer unplug the power cord from the power outlet to prevent damage to the devices 17
- Connect your rgb rgbw led strip to the header the power pin marked with a triangle on the plug of the led strip must be connected to pin 1 12v of the led strip header incorrect connection may lead to the damage of the led strip 17
- Cpu_opt water cooling cpu fan header 17
- For how to turn on off the lights of the led strip refer to the instructions on in chapter 2 bios setup peripherals 17
- Led_c1 led_c2 rgb rgbw led strip headers 17
- Pin no definition 17
- Pwm speed control 17
- Sys_fan3_pump system fan water cooling pump header 17
- The fan header is 4 pin and possesses a foolproof insertion design most fan headers possess a foolproof insertion design when connecting a fan cable be sure to connect it in the correct orientation the black connector wire is the ground wire the speed control function requires the use of a fan with fan speed control design 17
- The fan pump header is 4 pin and possesses a foolproof insertion design most fan headers possess a foolproof insertion design when connecting a fan cable be sure to connect it in the correct orientation the black connector wire is the ground wire the speed control function requires the use of a fan with fan speed control design for optimum heat dissipation it is recommended that a system fan be installed inside the chassis the header also provides speed control for a water cooling pump refer to chapter 2 bios setup m i t for more information 17
- The headers can be used to connect a standard 5050 rgb rgbw led strip 12v g r b w with maximum power rating of 2a 12v and maximum length of 2m 17
- Voltage speed control 17
- Before installing the devices be sure to turn off the devices and your computer unplug the power cord from the power outlet to prevent damage to the devices 18
- Chipset supports raid 0 raid 1 raid 5 and raid 10 refer to chapter 3 configuring a raid set for instructions on configuring a raid array 18
- Connect your digital led strip to the header there are 12v and 5v digital led strips be sure to verify the voltage requirements of your digital led strip and set the dled_v_sw1 and dled_v_sw2 jumpers accordingly the power pin marked with a triangle on the plug of the led strip must be connected to pin 1 of the digital led strip header incorrect connection may lead to the damage of the led strip 18
- D_led1 d_led2 digital led strip headers 18
- Dled_v_sw1 dled_v_sw2 digital led strip power select jumpers 18
- For how to turn on off the lights of the led strip refer to the instructions on in chapter 2 bios setup peripherals 18
- Sata3 0 1 2 3 4 5 sata 6gb s connectors 18
- The headers can be used to connect a standard 5050 digital led strip with maximum power rating of 2a 12v or 5v and maximum length of 5m or maximum number of 300 leds 18
- The jumpers allow you to select the supply voltage of the d_led1 and d_led2 headers be sure to verify the voltage requirements of your digital led strip and set the correct voltage with this jumper before connection incorrect connection may lead to the damage of the led strip 18
- The sata connectors conform to sata 6gb s standard and are compatible with sata 3gb s and sata 1 gb s standard each sata connector supports a single sata device the inte 18
- To enable hot plugging for the sata ports refer to chapter 2 bios setup peripherals sata and rst configuration for more information 18
- Due to the limited number of lanes provided by the chipset the availability of the sata connectors may be affected by the type of device installed in the m2p_32g connector the m2p_32g connector shares bandwidth with the sata3 0 connector refer to the following table for details 19
- Follow the steps below to correctly install an m ssd in the m connector step 1 use a screw driver to unfasten the screw and nut from the motherboard locate the proper mounting hole for the m ssd to be installed and then screw the nut first step 2 slide the m ssd into the connector at an angle step 3 press the m ssd down and then secure it with the screw 19
- Installationnoticesforthepciex4 m andsataconnectors 19
- M2p_32g 19
- M2p_32g m2q_32g m socket 3 connectors 19
- M2q_32g 19
- Note the pciex4 slot shares bandwidth with the m2q_32g connector the pciex4 slot becomes unavailable when an ssd is installed in the m2q_32g connector 19
- Select the proper hole for the m ssd to be installed and refasten the screw and nut 19
- The m connectors support m sata ssds or m pcie ssds and support raid configuration please note that an m pcie ssd cannot be used to create a raid set either with an m sata ssd or a sata hard drive to create a raid array with an m pcie ssd you must set up the configuration in uefi bios mode refer to chapter 3 configuring a raid set for instructions on configuring a raid array 19
- Ci chassis intrusion header gray connects to the chassis intrusion switch sensor on the chassis that can detect if the chassis cover has been removed this function requires a chassis with a chassis intrusion switch sensor 20
- Connect the power switch reset switch speaker chassis intrusion switch sensor and system status indicator on the chassis to this header according to the pin assignments below note the positive and negative pins before connecting the cables 20
- Connects to the power status indicator on the chassis front panel the led is on when the system is operating the led is off when the system is in s3 s4 sleep state or powered off s5 20
- F_audio front panel audio header 20
- F_panel front panel header 20
- Gnd 7 gnd 20
- Hd hard drive activity led blue connects to the hard drive activity led on the chassis front panel the led is on when the hard drive is reading or writing data 20
- Line2_r 10 sense 20
- Mic2_l 6 sense 20
- Mic2_r 8 no pin 20
- Nc 9 line2_l 20
- Nc orange no connection 20
- Pin no definition pin no definition 20
- Pled pwr_led power led yellow purple 20
- Pw power switch red connects to the power switch on the chassis front panel you may configure the way to turn off your system using the power switch refer to chapter 2 bios setup power for more information 20
- Res reset switch green connects to the reset switch on the chassis front panel press the reset switch to restart the computer if the computer freezes and fails to perform a normal restart 20
- S3 s4 s5 off 20
- Some chassis provide a front panel audio module that has separated connectors on each wire instead of a single plug for information about connecting the front panel audio module that has different wire assignments please contact the chassis manufacturer 20
- Speak speaker orange connects to the speaker on the chassis front panel the system reports system startup status by issuing a beep code one single short beep will be heard if no problem is detected at system startup 20
- System status led 20
- The front panel audio header supports high definition audio hd you may connect your chassis front panel audio module to this header make sure the wire assignments of the module connector match the pin assignments of the motherboard header incorrect connection between the module connector and the motherboard header will make the device unable to work or even damage it 20
- The front panel design may differ by chassis a front panel module mainly consists of power switch reset switch power led hard drive activity led speaker and etc when connecting your chassis front panel module to this header make sure the wire assignments and the pin assignments are matched correctly 20
- Do not plug the ieee 1394 bracket 2x5 pin cable into the usb 2 1 header prior to installing the usb bracket be sure to turn off your computer and unplug the power cord 21
- F_usb1 f_usb2 usb 2 1 headers 21
- F_usb30_1 f_usb30_2 usb 3 gen 1 headers 21
- From the power outlet to prevent damage to the usb bracket 21
- The headers conform to usb 2 1 specification each usb header can provide two usb ports via an optional usb bracket for purchasing the optional usb bracket please contact the local dealer 21
- The headers conform to usb 3 gen 1 and usb 2 specification and each header can provide two usb ports for purchasing the optional 3 front panel that provides two usb 3 gen 1 ports please contact the local dealer 21
- Tpm trusted platform module header 21
- You may connect a tpm trusted platform module to this header 21
- Add in card 22
- Add in card connector 22
- After system restart go to bios setup to load factory defaults select load optimized defaults or 22
- Always turn off your computer and unplug the power cord before replacing the battery replace the battery with an equivalent one damage to your devices may occur if the battery is 22
- Always turn off your computer and unplug the power cord from the power outlet before clearing 22
- B s_ b 22
- B_ f_usb3 f_usb30 3 22
- Bat battery 22
- Clr_cmos clear cmos jumper 22
- Contact the place of purchase or local dealer if you are not able to replace the battery by yourself 22
- Cpu cpu status led vga graphics card status led dram memory status led boot operating system status led 22
- Cpu vga dram boot status leds 22
- F_usb3 f 22
- F_usb30 f_ u 22
- Manually configure the bios settings refer to chapter 2 bios setup for bios configurations 22
- Object like a screwdriver to touch the positive and negative terminals of the battery holder making them short for 5 seconds 22
- Of the battery the positive side should face up 22
- Open normal 22
- Or uncertain about the battery model 22
- Replace the battery 4 plug in the power cord and restart your computer 22
- Replaced with an incorrect model 22
- S 3 b s s s 22
- S b_ b 22
- Short clear cmos values 22
- Supports a thunderbol 22
- Thb_c thunderbol 22
- The battery provides power to keep the values such as bios configurations date and time information in the cmos when the computer is turned off replace the battery when the battery voltage drops to a low level or the cmos values may not be accurate or may be lost 22
- The cmos values 22
- The status leds show whether the cpu graphics card memory and operating system are working properly after system power on if the cpu vga dram led is on that means the corresponding device is not working normally if the boot led is on that means you haven t entered the operating system yet 22
- This connector is for a gigabyte thunderbol 22
- Usb 0_ b 22
- Use this jumper to clear the bios configuration and reset the cmos values to factory defaults to clear the cmos values use a metal object like a screwdriver to touch the two pins for a few seconds 22
- Used batteries must be handled in accordance with local environmental regulations 22
- When installing the battery note the orientation of the positive side and the negative side 22
- You may clear the cmos values by removing the battery 1 turn off your computer and unplug the power cord 2 gently remove the battery from the battery holder and wait for one minute or use a metal 22
- _ s f_ 22
- _ s s_ _ b 22
- _ u _ b 22
- 1 startup screen 23
- Chapter 2 bios setup 23
- 2 m i t 24
- Advanced frequency settings 24
- Cpu base clock 24
- Cpu clock ratio 24
- Cpu frequency 24
- Cpu upgrad 24
- Fclk frequency for early power on 24
- Graphics slice rati 24
- Graphics unslice rati 24
- Host clock value 24
- Advanced cpu core settings 25
- Avx offset 25
- Core current limit amps 25
- Cpu flex ratio override 25
- Cpu flex ratio settings 25
- Cpuclockratio cpufrequency fclkfrequencyforearlypoweron 25
- Enhanced multi core performance 25
- Hyper threading technology 25
- Intel r speed shift technology inte 25
- Intel r turbo boost technology 25
- No of cpu cores enabled 25
- Power limit tdp watts power limit time 25
- Speed shift technology 25
- Turbo per core limit contro 25
- Turbo rati 25
- Uncore frequency 25
- Uncore ratio 25
- C10 state support 26
- C3 state support 26
- C6 c7 state support 26
- C8 state support 26
- Cpu eist function 26
- Cpu enhanced halt c1e 26
- Cpu thermal monitor 26
- Energyefficientturb 26
- Hardware prefetcher 26
- Package c state limit 26
- Race to halt rth 26
- Ring to core offset down bin 26
- Voltage optimization 26
- Adjacent cache line prefetch 27
- Advanced memory settings 27
- Extremememoryprofile x m p 27
- Memory boot mod 27
- Memory enhancement settings 27
- Memory frequency mhz 27
- Memory odd ratio 100 133 or 200 266 27
- Memory ref clock 27
- Memory timing mode 27
- Memoryoddratio 100 133or200 266 memoryfrequency mhz 27
- Realtime memory timing 27
- System memory multiplier 27
- Systemmemorymultiplier memoryrefclock 27
- Advanced power settings 28
- Advanced voltage settings 28
- Channel a b memory sub timings 28
- Channel interleaving 28
- Chipset voltage control 28
- Cpu core voltage control 28
- Cpu vcore loadline calibration 28
- Dram voltage control 28
- Internal vr control 28
- Memory multiplier tweaker 28
- Pc health status 28
- Profileddrvoltage 28
- Rank interleaving 28
- Reset case open status 28
- Vaxg loadline calibration 28
- 3dmark01 enhancement 29
- Case open 29
- Cpu vcore cpu vccsa dram channel a b voltage 3 v 5v 12v cpu vaxg 29
- Fan control use temperature input 29
- Fan pump control mode 29
- Fan pump fail warning 29
- Fan pump stop 29
- Fan speed 29
- Fan speed control 29
- Flow rate 29
- Max link speed 29
- Miscellaneous settings 29
- Monitor 29
- Smart fan 5 settings 29
- Temperature 29
- Temperature interval 29
- Temperature warning control 29
- 3 system 30
- Access level 30
- System date 30
- System language 30
- System time 30
- 4 bios 31
- Boot option priorities 31
- Bootup numlock state 31
- Fast boot 31
- Full screen logo show 31
- Hard drive cd dvd rom drive floppy drive network device bbs priorities 31
- Security option 31
- Csm support 32
- Lan pxe boot option rom 32
- Mouse speed 32
- Network stack driver support 32
- Next boot after ac power loss 32
- Ps2 devices support 32
- Sata support 32
- Storage boot option control 32
- Usb support 32
- Vga support 32
- Administrator password 33
- Other pci devices 33
- User password 33
- 5 peripherals 34
- Above 4g decoding 34
- Ez raid 34
- Initial display output 34
- Ledsinsleep hibernation andsoftoffstates 34
- Rgb fusion 34
- Intel platform trust technology ptt 35
- Intel r bios guard technology 35
- Intel r ethernet connection 35
- Ip6configurationpolicy 35
- Ipv4 http support 35
- Ipv4 pxe support 35
- Ipv6 http support 35
- Ipv6 pxe support 35
- Legacy usb support 35
- Media detect count 35
- Network stack 35
- Networkstackconfiguration 35
- Nvmeconfiguration 35
- Offboardsatacontrollerconfiguration 35
- Pxe boot wait time 35
- Sw guard extensions sgx 35
- Trusted computing 35
- Usbconfiguration 35
- Aggressive lpm support 36
- Configuredasesata 36
- Hot plug 36
- Mass storage devices 36
- Mechanical presence switch 36
- Port 0 1 2 3 4 5 36
- Port 60 64 emulation 36
- Sata controller s 36
- Sata mode selection 36
- Sataandrstconfiguration 36
- Usb mass storage driver support 36
- Xhci hand off 36
- 6 chipset 37
- Audio controller 37
- Dvmt pre allocated 37
- Dvmt total gfx mem 37
- High precision timer 37
- Internal graphics 37
- Ioapic 24 119 entries 37
- Pch lan controller 37
- Wake on lan enable 37
- 7 power 38
- Ac back 38
- Dmi aspm 38
- Pch aspm 38
- Peg aspm 38
- Platform power management 38
- Power on by keyboard 38
- Cec 2019 ready 39
- Power on by mouse 39
- Power on password 39
- Rc6 render standby 39
- Resume by alarm 39
- Soft off by pwr bttn 39
- 8 save exit 40
- Boot override 40
- Exit without saving 40
- Load optimized defaults 40
- Loadprofiles 40
- Save exit setup 40
- Saveprofiles 40
- 1 configuring a raid set 41
- 1 configuringaraidset 41
- A installing sata hard drive s in your computer 41
- B configuringsatacontrollermodeinbiossetup 41
- Beforeyoubegin pleasepreparethefollowingitems 41
- C 1 using ez raid 41
- Chapter 3 appendix 41
- Configuringtheonboardsatacontroller 41
- Raid levels 41
- C 2 uefiraidconfiguration 42
- C 3 configuringlegacyraidrom 42
- 2 installing an inte 43
- 2 installing an intel optane memory 43
- Installation guidelines a 1 installation in ahci mode 43
- Installing the operating system 43
- Installing the sata raid ahci driver and operating system 43
- Memory 43
- System requirements 43
- A 2 installation in intel rst premium with intel optane system acceleration mode 44
- 3 drivers installation 45
- Caution 46
- Fcc notice u s a only 46
- Canada industry canada ic 47
- European community directive red directive compliance statement 48
- Japan wireless statement 48
- Korea kcc ncc wireless statement 48
- Taiwan ncc wireless statements 無線設備警告聲明 48
- Our commitment to preserving the environment 49
- Regulatory notices 49
- Regulatory statements 49
- Restriction of hazardous substances rohs directive statement 49
- Waste electrical electronic equipment weee directive statement 49
- Weee symbol statement 49
- Contact us 52
- Gigabyte esupport 52
- To submit a technical or non technical sales marketing question please link to http esupport gigabyte com 52
Похожие устройства
- Gigabyte Z370 AORUS ULTRA GAMING 2.0 Инструкция по эксплуатации
- Gigabyte Z370 AORUS ULTRA GAMING WIFI Инструкция по эксплуатации
- Gigabyte Z370 HD3 Инструкция по эксплуатации
- Gigabyte Z370 HD3P Инструкция по эксплуатации
- Gigabyte Z370 UD3H Инструкция по эксплуатации
- Gigabyte Z370M D3H Инструкция по эксплуатации
- Gigabyte Z370M DS3H Инструкция по эксплуатации
- Gigabyte Z370N WIFI Инструкция по эксплуатации
- Gigabyte Z370P D3 Инструкция по эксплуатации
- Gigabyte Z370XP SLI Инструкция по эксплуатации
- Horstek TC 215 v5 Инструкция по эксплуатации
- Horstek TC 415 Инструкция по эксплуатации
- Horstek TC 715 Инструкция по эксплуатации
- Horstek TC 515 Инструкция по эксплуатации
- Horstek TC 015 Инструкция по эксплуатации
- Horstek TC 325 Инструкция по эксплуатации
- Horstek TC 315 Инструкция по эксплуатации
- Etari ET-111S Инструкция по эксплуатации
- Etari MD-666 Инструкция по эксплуатации
- Etari MD-07 Инструкция по эксплуатации