Home
Главная
Maxwell
Утюг
MW-3010
Инструкция по эксплуатации Страница: 9

Maxwell MW-3010 [9/44] English

Maxwell MW-3010 [9/44] English

9

ENGLISH

CHOICE OF WATER

• To fill the water tank use regular tap wa-

ter. If the water is hard then it is recom-

mended to mix it with distilled water at a

ratio of 1:1, if the water is very hard, mix it

with distilled water at a ratio of 1:2 or use

only distilled water.

Note:

Do not fill the water tank (10) with

scented liquids, vinegar, starch solu-

tions, descaling reagents, chemical

substances etc.

FILLING THE WATER TANK

Make sure that the iron is disconnected

from electrical power before filling it with

water.

• Set the steam release regulator (3) to the

position of steam vapor OFF.

• Open the water tank lid (2).

• Fill it with water using the water tank (10).

Close the lid (2).

Note:

• Do not fill it with water above MAX. in-

dication.

• If you need to refill the water tank dur-

ing ironing, turn off the iron and un-

plug the power cord from the outlet.

• After you finish ironing, open the wa-

ter tank lid (2) and drain the remain-

ing water.

IRONING TEMPERATURE

Before operating test the heated iron on

the old cloth to be sure that the iron sole

(13) and the water tank (10) are clean.

• Always check the recommended iron

temperature indicated on the tag before

ironing.

• If the tag does not list the recommended

ironing temperature, but you know the

type of fabric, then use the following

table to determine the proper tempera-

ture.

Signs Fabric type/temperature

•

Synthetics, nylon, acryl, polyester

(low temperature)

••

Silk/wool (medium temperature)

•••

Cotton/flax (high temperature)

• This table is only for smooth materials.

Fabrics of other types (crimped, raised

etc.) are best ironed at low temperature.

• First sort items by ironing temperature:

wool with wool, cotton with cotton etc.

• The iron heats up faster than is cools

down. For this reason it is recommended

to begin ironing at low temperature (for

instance synthetic fabrics). After that,

move to higher temperature ironing.

Cotton and linens should be ironed last.

• If an item is made from a mix of fabrics,

then the iron should be set for the fab-

ric with the lowest ironing (for instance if

an item is made from 60% polyester and

40% cotton, it should be ironed at the

temperature used for ironing polyester

“•”).

• If you cannot define the fabric the item is

made from, find a place on it that is hid-

den while wearing and, on practice select

the ironing temperature (always start at

the lowest and gradually raise it until you

get the desired result.)

• Corduroy and other fabrics that start

glossy quickly should be ironed strictly in

one direction (along the lines) with slight

pressure.

• To avoid appearance of glossy spots on

the synthetic and silk fabrics, iron them

back-side.

SETTING THE IRONING TEMPERATURE

• Place the iron on the base (8).

• Insert the power plug into the outlet.

• Set the temperature regulator (11) to the

required ironing temperature: “•”, “••”,

“•••” or “max” (depending on the type

of fabric), the (9) indicator will light up.

• When the sole temperature (13) reaches

MW-3010.indd 9MW-3010.indd 9 03.12.2009 14:50:1403.12.2009 14:50:14

Содержание

Похожие устройства

Случайные обсуждения

Ответы 1

Здравствуйте! МНЕ нужно знать до какой температуры утюг нагревается на функции wool,cotton,linen?

11 лет назад

Ответы 1

Длина шнура?

3 года назад

Ответы 1

разборка утюга масквел 3010.

8 лет назад