Hallde RG-100 380В [5/33] Check every week
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Hallde RG-100 380В [5/33] Check every week

Hallde RG-100 380В [5/33] Check every week
CHECK EVERY WEEK
That the machine stops as soon as the
pusher plate (1:A) has been moved up and
restarts when the pusher plate has been
lowered.
That the machine cannot be started with the
feeder/lid (1:C) removed and with the
pusher plate lowered.
Remove the plug from the power supply
socket and then check that the electric
cable is in good condition and is not
cracked on the outside.
If any of the two safety functions does not
perform as intended or if the electric cable
is cracked, get a specialist to attend to the
machine before connecting it back to the
power supply.
Check that the pusher plate shaft (1:I) has
been lubricated as necessary and runs
freely. If the shaft does not run freely, clean
it carefully and lubricate it with a few drops
of machine oil.
Check that the knives and shredder plates
are in good condition and are sharp.
TROUBLE -SHOOTING
FAULT: The machine cannot be started, or
stops while it is running and cannot be
restarted. REMEDY: Check that the plug is
securely fitted into the power supply socket.
Check that the feeder/lid (1:C) is locked in
the correct position. Move down the pusher
plate (1:A) into the feeder/lid. Check that
the fuses in the fuse box for the premises
have not blown and that they have the
correct rating. Wait for a few minutes and
try to restart the machine. If the machine still
fails to run, call a specialist.
FAULT: Low capacity or poor cutting
results. REMEDY: Make sure that you are
using the correct cutting tool or
combination of cuttings tools (3). Check
that the knives and shredder plates are in
good condition and are sharp. Press the
food down loosely.
FAULT: The cutting tool (3) cannot be
removed. REMEDY: Always use the ejector
plate (1:D). Use a thick leather glove or the
like that the knives of the cutting tool cannot
cut through, and turn the cutting tool
clockwise to release it.
TECHNICAL SPECIFICATION
MACHINE: Motor: 0.25 kW, 230 V, single-
phase, 50 Hz, with thermal motor
protection. Transmission: gears. Safety
system: Two safety switches. Degree of
protection: IP44. Power supply socket:
Earthed, single-phase, 10 A. Fuse in fuse
box for the premises: 10 A, slow-blow.
Sound level LpA (EN31201): 70 dBA.
TOOLS: Diameter: 185 mm. Speed: 350
rpm.
MATERIALS: Machine housing: Anodized
or polished aluminium alloy. Cutting tool
discs: Aluminium or polyurethane. Cutting
tool knives: Knife steel of the highest quality.
NET WEIGHTS: Machine: 16 kg. Cutting
tools: About 0.5 kg on average.
STANDARDS: NSF STANDARD 8, EU
Machine Directive 89/392EEC.

Содержание

Похожие устройства

CHECK EVERY WEEK Thal the machine stops as soon as the pusher plale 1 A has been moved up and restarts when the pusher plate has been lowered Thal the machine cannot be started with the feeder lid 1 C removed and with the pusher plate lowered Remove the plug from the power supply socket and then check that the electric cable is in good condition and is not cracked on the outside If any of the two safety functions does not perform as intended or if the electric cable is cracked gel a specialist Io allend Io the machine before connecting it back to the power supply Check that the pusher plate shaft 1 l has been lubricated as necessary and runs freely If the shaft does not run freely clean it carefully and lubricate it with a few drops of machine oil Check that the knives and shredder plates are in good condition and are sharp TROUBLE SHOOTING FAULT The machine cannot be started or stops while it is running and cannot be restarted REMEDY Check that the plug is securely fitted into the power supply socket Check that the feeder lid 1 C is locked in the correct position Move down the pusher plate 1 A into the feeder lid Check that the fuses in the fuse box for the premises have not blown and that they have the correct rating Wail for a few minutes and try to restart the machine If the machine still fails Io run call a specialist FAULT Low capacity or poor culling results REMEDY Make sure that you are using the correct cutting tool or combination of cullings tools 3 Check that the knives and shredder plates are in good condition and are sharp Press the food down loosely FAULT The culling tool 3 cannot be removed REMEDY Always use the ejector plate 1 D Use a thick leather glove or the like that the knives of the culling tool cannol cut through and turn the cutting tool clockwise Io release it TECHNICAL SPECIFICATION MACHINE Motor 0 25 kW 230 V single phase 50 Hz with thermal motor protection Transmission gears Safety system Two safety switches Degree of protection IP44 Power supply socket Earthed single phase 10 A Fuse in fuse box for the premises 10 A slow blow Sound level LpA EN 31201 70 dBA TOOLS Diameter 185 mm Speed 350 rpm MATERIALS Machine housing Anodized or polished aluminium alloy Culling tool discs Aluminium or polyurethane Culling tool knives Knife steel of the highest quality NETWEIGHTS Machine 16 kg Cutting tools About 0 5 kg on average STANDARDS NSF STANDARD 8 EU Machine Directive 89 392EEC

Скачать